Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR DOOR SPEAKER
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0448057 REAR DOOR SPEAKER G

AUDIO / VIDEO  REAR DOOR SPEAKER  INSPECTION  


PROCEDURE

Hide 86160B 1.INSPECT REAR SPEAKER ASSEMBLY (for LH Side)

a.

With the speaker in the installed condition, check there are no abnormalities such looseness or rattling.


b.

Check that there is no foreign matter inside the speaker.


c.

Check that the speaker cone is not damaged.


d.
E364209C68
1.552,0.354 1.896,0.563 0.344,0.208 0.948,1.26 1.552,1.26 true 1.906,1.25 2.5,1.25 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.604,0.385 1.896,0.563 0.292,0.177 10 false F18 0.771,1.167 0.927,1.365 0.156,0.198 10 false + 2.552,1.146 2.708,1.344 0.156,0.198 10 false -
*a Component without harness connected
(Rear Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

i.

for 6 Speakers:

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F18)Location & Routing

Click Connector(F18)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Speaker Assembly LH

F18-1(-) - F18-2(+) Always 4 Ω


If the result is not as specified, replace the rear speaker assembly.


ii.

for 14 Speakers:

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F18)Location & Routing

Click Connector(F18)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Speaker Assembly LH

F18-1(-) - F18-2(+) Always 3.3 to 4.9 Ω


If the result is not as specified, replace the rear speaker assembly.



Hide 86160B 2.INSPECT REAR SPEAKER ASSEMBLY (for RH Side)

a.

With the speaker in the installed condition, check there are no abnormalities such looseness or rattling.


b.

Check that there is no foreign matter inside the speaker.


c.

Check that the speaker cone is not damaged.


d.
E364209C69
1.594,0.354 1.896,0.563 0.302,0.208 0.948,1.26 1.563,1.26 true 1.906,1.25 2.5,1.25 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.646,0.385 1.865,0.563 0.219,0.177 10 false F7 0.771,1.167 0.927,1.365 0.156,0.198 10 false + 2.552,1.146 2.708,1.344 0.156,0.198 10 false -
*a Component without harness connected
(Rear Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

i.

for 6 Speakers:

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F7)Location & Routing

Click Connector(F7)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Speaker Assembly RH

F7-1(-) - F7-2(+) Always 4 Ω


If the result is not as specified, replace the rear speaker assembly.


ii.

for 14 Speakers:

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F7)Location & Routing

Click Connector(F7)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Speaker Assembly RH

F7-1(-) - F7-2(+) Always 3.3 to 4.9 Ω


If the result is not as specified, replace the rear speaker assembly.



Hide 86160Y 3.INSPECT REAR NO. 2 SPEAKER ASSEMBLY (for 14 Speakers)

a.

With the speaker in the installed condition, check there are no abnormalities such looseness or rattling.


b.

Check that there is no foreign matter inside the speaker.


c.

Check that the speaker cone is not damaged.


d.

When there is a malfunction such as noise from a speaker or no sound at all, replace the speaker with a new one and check that the malfunction disappears.

OK:

Malfunction disappears.


HINT:
·

When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

·

Perform the inspection above on both the LH and RH sides.