Home › Audio / Visual / Telematics › AUDIO / VIDEO › INSTRUMENT PANEL SPEAKER
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0448058 INSTRUMENT PANEL SPEAKER G

AUDIO / VIDEO  INSTRUMENT PANEL SPEAKER  INSPECTION  


PROCEDURE

Hide 86160P 1.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

a.

for 6 Speakers:

i.

With the speaker in the installed condition, check there are no abnormalities such looseness or rattling.


ii.

Check that there is no foreign matter inside the speaker.


iii.

Check that the speaker cone is not damaged.


iv.

Replace and check.

OK:

Malfunction disappears.


HINT:

Switch the right and left speakers and perform a check when either the right or left front No. 2 speaker assembly is suspected to be malfunctioning.




b.

for 14 Speakers:

i.

With the speaker in the installed condition, check there are no abnormalities such looseness or rattling.


ii.

Check that there is no foreign matter inside the speaker.


iii.

Check that the speaker cone is not damaged.


iv.
E364209C70
1.51,0.354 1.896,0.573 0.385,0.219 0.948,1.26 1.542,1.26 true 1.906,1.25 2.5,1.25 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.573,0.385 1.875,0.552 0.302,0.167 10 false D83 0.771,1.167 0.927,1.365 0.156,0.198 10 false + 2.552,1.146 2.708,1.344 0.156,0.198 10 false -
*a Component without harness connected
(Front No. 2 Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D83)Location & Routing

Click Connector(D83)Instrument Panel>Instrument Panel Wire>Front No .2 Speaker Assembly LH

D83-1(-) - D83-2(+) Always 2.8 to 3.8 Ω


If the result is not as specified, replace the front No. 2 speaker assembly.



Hide 86160P 2.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

a.

for 6 Speakers:

i.

With the speaker in the installed condition, check there are no abnormalities such looseness or rattling.


ii.

Check that there is no foreign matter inside the speaker.


iii.

Check that the speaker cone is not damaged.


iv.

Replace and check.

OK:

Malfunction disappears.


HINT:

Switch the right and left speakers and perform a check when either the right or left front No. 2 speaker assembly is suspected to be malfunctioning.




b.

for 14 Speakers:

i.

With the speaker in the installed condition, check there are no abnormalities such looseness or rattling.


ii.

Check that there is no foreign matter inside the speaker.


iii.

Check that the speaker cone is not damaged.


iv.
E364209C71
1.563,0.365 1.927,0.573 0.365,0.208 0.948,1.26 1.542,1.26 true 1.906,1.25 2.5,1.25 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.594,0.385 1.896,0.573 0.302,0.188 10 false D82 0.771,1.167 0.927,1.365 0.156,0.198 10 false + 2.552,1.146 2.708,1.344 0.156,0.198 10 false -
*a Component without harness connected
(Front No. 2 Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D82)Location & Routing

Click Connector(D82)Instrument Panel>Instrument Panel Wire>Front No. 2 Speaker Assembly RH

D82-1(-) - D82-2(+) Always 2.8 to 3.8 Ω


If the result is not as specified, replace the front No. 2 speaker assembly.



Hide 86160P 3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY (for Center)

a.

With the speaker in the installed condition, check there are no abnormalities such looseness or rattling.


b.

Check that there is no foreign matter inside the speaker.


c.

Check that the speaker cone is not damaged.


d.
E364209C72
1.49,0.344 1.896,0.552 0.406,0.208 0.948,1.26 1.542,1.26 true 1.906,1.25 2.5,1.25 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.563,0.385 1.833,0.552 0.271,0.167 10 false D59 0.771,1.167 0.927,1.365 0.156,0.198 10 false + 2.552,1.146 2.708,1.344 0.156,0.198 10 false -
*a Component without harness connected
(Front No. 2 Speaker Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D59)Location & Routing

Click Connector(D59)Instrument Panel>Instrument Panel Wire>Front No. 2 Speaker Assembly

D59-1(-) - D59-2(+) Always 2.8 to 3.8 Ω


If the result is not as specified, replace the front No. 2 speaker assembly.