Home › Audio / Visual / Telematics › AUDIO / VIDEO › NOISE FILTER
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0448062 NOISE FILTER G

AUDIO / VIDEO  NOISE FILTER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 86011R 1.INSPECT RADIO SETTING CONDENSER (for High Mounted Stop Light)

a.

With the radio setting condenser installed, check that there is no looseness or other abnormalities.


b.
E386542C12
1.594,0.417 2.073,0.333 true 2.125,0.229 2.281,0.427 0.156,0.198 10 false 1 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a
*a Radio Setting Condenser


Measure the resistance of the radio setting condenser according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground
·

Power switch off

·

High mounted stop light off

·

Luggage compartment room light off

·

Front door courtesy light assembly LH off

·

Rear door courtesy light assembly LH off


Below 1 Ω


If the result is not as specified, replace the radio setting condenser.


c.

Remove the bolt.


d.

Detach the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.


e.
E211797C38
1.948,0.625 2.604,0.438 true 1.896,0.885 2.51,1.281 true 1.906,1.656 2.552,1.792 true 2.635,0.323 2.771,0.521 0.135,0.198 10 false 1 2.542,1.188 2.677,1.385 0.135,0.198 10 false 2 2.563,1.698 2.698,1.896 0.135,0.198 10 false 3 0.073,0 0.281,0.198 0.208,0.198 10 false *a
*a Radio Setting Condenser


Measure the resistance of the radio setting condenser according to the value(s) in the table below.

NOTICE:

Before measuring the resistance, be sure to use insulated probes to avoid a short circuit between the tester terminal and bracket.


Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2
·

Power switch off

·

High mounted stop light off

·

Luggage compartment room light off

·

Front door courtesy light assembly LH off

·

Rear door courtesy light assembly LH off


10 kΩ or higher
1 - 3 10 kΩ or higher


If the result is not as specified, replace the radio setting condenser.


f.
E211797C37
2.406,1.729 1.927,1.729 true 1.917,0.917 2.448,1.177 true 2.5,1.115 2.635,1.281 0.135,0.167 10 false 2 2.5,1.667 2.625,1.823 0.125,0.156 10 false 3 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a
*a Radio Setting Condenser


Measure the voltage of the radio setting condenser according to the value(s) in the table below.

NOTICE:

Before measuring the voltage, be sure to use insulated probes to avoid a short circuit between the tester terminal and bracket.


Standard Voltage:
Tester Connection Condition Specified Condition
2 - Body ground
·

Power switch on

·

High mounted stop light off

·

Luggage compartment room light off

·

Front door courtesy light assembly LH off

·

Rear door courtesy light assembly LH off


Below 1 V
3 - Body ground Below 1 V
2 - Body ground
·

Power switch on

·

High mounted stop light on

·

Luggage compartment room light on

·

Front door courtesy light assembly LH on

·

Rear door courtesy light assembly LH on


11 to 14 V
3 - Body ground 11 to 14 V


If the result is not as specified, replace the radio setting condenser.


Hide 86011V 2.INSPECT RADIO SETTING CONDENSER (for Window Defogger)

a.

With the radio setting condenser installed, check that there is no looseness or other abnormalities.


b.
E386541C20
1.01,0.479 1.594,0.479 false 0.875,0.385 1.031,0.583 0.156,0.198 10 false 1 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a
*a Radio Setting Condenser


Measure the resistance of the radio setting condenser according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground
·

Power switch off

·

Window Defogger turned off


Below 1 Ω


If the result is not as specified, replace the radio setting condenser.


c.

Remove the bolt.


d.

Detach the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.


e.
E230106C48
2.083,1.583 2.542,1.427 true 1.344,1.594 0.813,1.427 true 2.594,1.333 2.708,1.49 0.115,0.156 10 false 3 0.667,1.323 0.781,1.479 0.115,0.156 10 false 2 0.063,0.073 0.271,0.229 0.208,0.156 10 false *a
*a Radio Setting Condenser


Measure the resistance of the radio setting condenser according to the value(s) in the table below.

NOTICE:

Before measuring the resistance, be sure to use insulated probes to avoid a short circuit between the tester terminal and bracket.


Standard Resistance:
Tester Connection Condition Specified Condition
2 - 3
·

Power switch off

·

Window Defogger turned off


10 kΩ or higher


If the result is not as specified, replace the radio setting condenser.


f.

Measure the voltage of the radio setting condenser according to the value(s) in the table below.

NOTICE:

Before measuring the voltage, be sure to use insulated probes to avoid a short circuit between the tester terminal and bracket.


Standard Voltage:
Tester Connection Condition Specified Condition
2 - Body ground
·

Power switch on

·

Window Defogger turned off


Below 1 V
2 - Body ground
·

Power switch on

·

Window Defogger turned on


11 to 14 V


If the result is not as specified, replace the radio setting condenser.