Home › Audio / Visual / Telematics › TELEMATICS › MAYDAY SWITCH
RM37H0E _56 Audio / Visual / Telematics _095262 TELEMATICS _0448091 MAYDAY SWITCH G

TELEMATICS  MAYDAY SWITCH  INSPECTION  


PROCEDURE

Hide 1.INSPECT MAYDAY SWITCH (MAP LIGHT ASSEMBLY)

a.

Measure the resistance according to the value(s) in the table below.

E455410C05
3.396,0.115 3.813,0.344 0.417,0.229 4,1.146 4,1.656 4,1.656 4.99,1.656 true 2.177,1.646 3.063,1.646 3.063,1.646 3.063,0.979 true 3.469,0.156 3.781,0.344 0.313,0.188 10 false H10 5.063,1.573 5.406,1.74 0.344,0.167 10 false SIG1 1.719,1.563 2.156,1.74 0.438,0.177 10 false GND3 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a
*a Component without harness connected
(Mayday Switch (Map Light Assembly))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H10)Location & Routing

Click Connector(H10)Body>No. 1 Roof Wire>Map Light Assembly

H10-13(SIG1) - H10-9(GND3) Manual (SOS) switch not pressed 408 to 417 Ω
H10-13(SIG1) - H10-9(GND3) Manual (SOS) switch pressed 81 to 83 Ω


If the result is not as specified, replace the mayday switch (map light assembly).


b.

Inspect the operation (red indicator)

i.

Check that each indicator illuminates when 2 dry cell batteries are connected to the mayday switch (map light assembly) connector terminals.

E455410C06
3.396,0.115 3.813,0.344 0.417,0.229 3.521,0.969 3.521,1.646 3.521,1.646 4.698,1.646 true 2.177,1.646 3.063,1.646 3.063,1.646 3.063,0.979 true 3.469,0.156 3.792,0.333 0.323,0.177 10 false H10 4.771,1.573 5.115,1.74 0.344,0.167 10 false IND1 1.75,1.563 2.177,1.75 0.427,0.188 10 false GND3 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a
*a Component without harness connected
(Mayday Switch (Map Light Assembly))
- -


NOTICE:

Do not apply more than 3 V.


OK:
Tester Connection Condition Specified Condition

Click Location & Routing(H10)Location & Routing

Click Connector(H10)Body>No. 1 Roof Wire>Map Light Assembly

H10-6(IND1) - H10-9(GND3) H10-6(IND1) - Battery positive (+)
H10-9(GND3) - Battery negative (-)
Red indicator comes on.


If the result is not as specified, replace the mayday switch (map light assembly).



c.

Inspect the operation (green indicator)

i.

Check that each indicator illuminates when 2 dry cell batteries are connected to the mayday switch (map light assembly) connector terminals.

E455410C07
3.396,0.115 3.813,0.344 0.417,0.229 3.365,0.969 3.365,1.646 3.365,1.646 4.677,1.646 true 2.177,1.646 3.063,1.646 3.063,1.646 3.063,0.979 true 3.469,0.156 3.802,0.354 0.333,0.198 10 false H10 4.771,1.573 5.115,1.74 0.344,0.167 10 false IND2 1.74,1.563 2.156,1.75 0.417,0.188 10 false GND3 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a
*a Component without harness connected
(Mayday Switch (Map Light Assembly))
- -


NOTICE:

Do not apply more than 3 V.


OK:
Tester Connection Condition Specified Condition

Click Location & Routing(H10)Location & Routing

Click Connector(H10)Body>No. 1 Roof Wire>Map Light Assembly

H10-7(IND2) - H10-9(GND3) H10-7(IND2) - Battery positive (+)
H10-9(GND3) - Battery negative (-)
Green indicator comes on.


If the result is not as specified, replace the mayday switch (map light assembly).



d.

Inspect the operation (SOS indicator)

i.

Check that each indicator illuminates when auxiliary battery are connected to the mayday switch (map light assembly) connector terminals.

E455410C08
3.396,0.115 3.813,0.344 0.417,0.229 3.677,0.969 3.677,1.646 3.677,1.646 4.76,1.646 true 2.177,1.646 3.063,1.646 3.063,1.646 3.063,0.979 true 3.469,0.156 3.74,0.333 0.271,0.177 10 false H10 4.813,1.573 5.156,1.74 0.344,0.167 10 false RRID 1.75,1.542 2.167,1.729 0.417,0.188 10 false GND3 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a
*a Component without harness connected
(Mayday Switch (Map Light Assembly))
- -


OK:
Tester Connection Condition Specified Condition

Click Location & Routing(H10)Location & Routing

Click Connector(H10)Body>No. 1 Roof Wire>Map Light Assembly

H10-5(RRID) - H10-9(GND3) H10-5(RRID) - Auxiliary battery positive (+)
H10-9(GND3) - Auxiliary battery negative (-)
SOS indicator comes on.


If the result is not as specified, replace the mayday switch (map light assembly).