Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY
RM37H0E _58 Vehicle Interior _095297 SEAT BELT _0448140 FRONT SEAT OUTER BELT ASSEMBLY G

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  INSPECTION  


PROCEDURE

Hide 73220 1.INSPECT FRONT SEAT OUTER BELT ASSEMBLY LH

CAUTION:
B395346

·

The front seat outer belt assembly LH contains an internal pretensioner, so when performing component inspection, make sure not to accidentally connect the auxiliary battery to the pretensioner connector terminal.

·

If the auxiliary battery is connected to the pretensioner connector terminal, the pretensioner will activate, which could result in serious injury.



a.

Check the seat belt tension reducer operation.

i.
B475625C11
0.583,2.104 0.979,2.323 0.396,0.219 0.927,2.698 1.188,2.24 true 0.646,2.708 0.354,2.531 true 0.229,2.021 0.542,2.177 0.313,0.156 10 false *a 1.177,2.073 1.49,2.271 0.313,0.198 10 false IG 0.229,2.406 0.542,2.604 0.313,0.198 10 false L 0.656,2.135 1.115,2.333 0.458,0.198 10 false G61
*a Component without harness connected
(Front Seat Outer Belt Assembly LH)


Check the operating sound.

OK:
Tester Connection Specified Condition

Click Location & Routing(G61)Location & Routing

Click Connector(G61)Body>Floor Wire / No. 3 Floor Wire>Front Seat Outer Belt Assembly LH

G61-1 (IG) - Auxiliary battery positive (+)
G61-2 (L) - Auxiliary battery negative (-)
Operating sound is heard when the magnetized solenoid is attracting the plunger



ii.

Pull out the seat belt again, disconnect the negative (-) lead of the auxiliary battery and allow the seat belt to retract. Listen to the operating sound again and check that the operating sound volume has increased.

If the result is not as specified, replace the front seat outer belt assembly LH.



b.
B491912C02
2.458,0.042 2.771,0.198 0.313,0.156 10 false *a 0.396,1.667 0.708,1.823 0.313,0.156 10 false *b 1.271,0.594 1.583,0.75 0.313,0.156 10 false *c
*a Unlock
*b Lock
*c 45°


Before installing the front seat outer belt assembly LH, check the ELR function.

NOTICE:

Do not disassemble the retractor.


i.

When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

If the result is not as specified, replace the front seat outer belt assembly LH.



Hide 73210 2.INSPECT FRONT SEAT OUTER BELT ASSEMBLY RH

CAUTION:
B395346

·

The front seat outer belt assembly RH contains an internal pretensioner, so when performing component inspection, make sure not to accidentally connect the auxiliary battery to the pretensioner connector terminal.

·

If the auxiliary battery is connected to the pretensioner connector terminal, the pretensioner will activate, which could result in serious injury.



a.

Check the seat belt tension reducer operation.

i.
B475625C12
0.583,2.104 0.979,2.323 0.396,0.219 0.927,2.698 1.188,2.24 true 0.646,2.708 0.354,2.531 true 0.229,2.021 0.542,2.177 0.313,0.156 10 false *a 1.177,2.073 1.49,2.271 0.313,0.198 10 false IG 0.229,2.406 0.542,2.604 0.313,0.198 10 false L 0.656,2.135 1.115,2.333 0.458,0.198 10 false G42
*a Component without harness connected
(Front Seat Outer Belt Assembly RH)


Check the operating sound.

OK:
Tester Connection Specified Condition

Click Location & Routing(G42)Location & Routing

Click Connector(G42)Body>Floor Wire / No. 3 Floor Wire>Front Seat Outer Belt Assembly RH

G42-1 (IG) - Auxiliary battery positive (+)
G42-2 (L) - Auxiliary battery negative (-)
Operating sound is heard when the magnetized solenoid is attracting the plunger



ii.

Pull out the seat belt again, disconnect the negative (-) lead of the auxiliary battery and allow the seat belt to retract. Listen to the operating sound again and check that the operating sound volume has increased.

If the result is not as specified, replace the front seat outer belt assembly RH.



b.
B491912C03
2.458,0.042 2.771,0.198 0.313,0.156 10 false *a 0.396,1.667 0.708,1.823 0.313,0.156 10 false *b 1.271,0.594 1.583,0.75 0.313,0.156 10 false *c
*a Unlock
*b Lock
*c 45°


Before installing the front seat outer belt assembly RH, check the ELR function.

NOTICE:

Do not disassemble the retractor.


i.

When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

If the result is not as specified, replace the front seat outer belt assembly RH.