Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Front Door)
RM37H0E _59 Vehicle Exterior _095305 WINDOW / GLASS _0448198 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


PROCEDURE

Hide 85720D 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NOTICE:
·

Do not apply positive (+) auxiliary battery voltage to any terminals, except terminal E20-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION



a.

Check that the motor gear rotates smoothly as follows.

E444318C02
2.385,0.667 2.729,0.854 0.344,0.188 4.031,1.896 4.698,1.896 true 2.74,1.333 3.156,1.333 true 2,1.333 2.417,1.333 true 2.781,1.667 3.042,2.031 true 2.063,2.042 2.385,1.677 true 1.563,0.438 1.875,0.594 0.313,0.156 10 false *a 3.885,1.823 4.198,1.979 0.313,0.156 10 false *b 3.198,1.271 3.656,1.469 0.458,0.198 10 false GND 1.896,1.271 2.354,1.469 0.458,0.198 10 false B 2.896,2.063 3.354,2.26 0.458,0.198 10 false DOWN 1.979,2.063 2.438,2.26 0.458,0.198 10 false UP 2.438,0.688 2.896,0.885 0.458,0.198 10 false E20
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


OK:
Tester Connection Specified Condition

Click Location & Routing(E20)Location & Routing

Click Connector(E20)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly LH

1.

Connect the positive (+) lead of the auxiliary battery to terminal E20-2 (B) and the negative (-) lead to terminal E20-1 (GND), and hold for 3 seconds or more.

2.

While terminals E20-2 (B) and E20-1 (GND) are connected, connect the negative (-) lead of the auxiliary battery to terminal E20-10 (UP).

3.

After disconnecting the negative (-) lead of the auxiliary battery from terminal E20-10 (UP), connect terminal E20-10 (UP) to the negative (-) lead of the auxiliary battery again within 1 second.


Motor gear rotates counterclockwise (UP)
1.

Connect the positive (+) lead of the auxiliary battery to terminal E20-2 (B) and the negative (-) lead to terminal E20-1 (GND), and hold for 3 seconds or more.

2.

While terminals E20-2 (B) and E20-1 (GND) are connected, connect the negative (-) lead of the auxiliary battery to terminal 20-7 (DOWN).

3.

After disconnecting the negative (-) lead of the auxiliary battery from terminal E20-7 (DOWN), connect terminal E20-7 (DOWN) to the negative (-) lead of the auxiliary battery again within 1 second.


Motor gear rotates clockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly LH.


Hide 85710E 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NOTICE:
·

Do not apply positive (+) auxiliary battery voltage to any terminals, except terminal E2-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION



a.

Check that the motor gear rotates smoothly as follows.

E444317C02
4.656,0.646 5.01,0.833 0.354,0.188 2.677,1.885 3.344,1.885 true 4.229,1.333 4.646,1.333 true 4.969,1.333 5.385,1.333 true 5.021,1.667 5.292,1.948 true 4.24,1.938 4.625,1.667 true 3.792,0.458 4.042,0.635 0.25,0.177 10 false *a 3.385,1.823 3.698,1.979 0.313,0.156 10 false *b 4.135,1.271 4.292,1.469 0.156,0.198 10 false B 5.417,1.271 5.833,1.521 0.417,0.25 10 false GND 5.167,1.969 5.667,2.219 0.5,0.25 10 false DOWN 4.167,1.958 4.5,2.208 0.333,0.25 10 false UP 4.75,0.667 5,0.844 0.25,0.177 10 false E2
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


OK:
Tester Connection Specified Condition

Click Location & Routing(E2)Location & Routing

Click Connector(E2)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

1.

Connect the positive (+) lead of the auxiliary battery to terminal E2-2 (B) and the negative (-) lead to terminal E2-1 (GND), and hold for 3 seconds or more.

2.

While terminals E2-2 (B) and E2-1 (GND) are connected, connect the negative (-) lead of the auxiliary battery to terminal E2-10 (UP).

3.

After disconnecting the negative (-) lead of the auxiliary battery from terminal E2-10 (UP), connect terminal E2-10 (UP) to the negative (-) lead of the auxiliary battery again within 1 second.


Motor gear rotates clockwise (UP)
1.

Connect the positive (+) lead of the auxiliary battery to terminal E2-2 (B) and the negative (-) lead to terminal E2-1 (GND), and hold for 3 seconds or more.

2.

While terminals E2-2 (B) and E2-1 (GND) are connected, connect the negative (-) lead of the auxiliary battery to terminal E2-7 (DOWN).

3.

After disconnecting the negative (-) lead of the auxiliary battery from terminal E2-7 (DOWN), connect terminal E2-7 (DOWN) to the negative (-) lead of the auxiliary battery again within 1 second.


Motor gear rotates counterclockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly RH.