Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door)
RM37H0E _59 Vehicle Exterior _095305 WINDOW / GLASS _0448199 POWER WINDOW REGULATOR MOTOR(for Rear Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  INSPECTION  


PROCEDURE

Hide 85720D 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NOTICE:
·

Do not apply positive (+) auxiliary battery voltage to any terminals, except terminal F12-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION



a.

Check that the motor gear rotates smoothly as follows.

E444324C04
4.313,0.635 4.677,0.823 0.365,0.188 2.323,1.792 2.99,1.792 true 3.917,1.333 4.333,1.333 true 4.656,1.333 5.073,1.333 true 4.677,1.667 4.896,1.948 true 4.083,1.948 4.292,1.677 true 3.51,0.479 3.823,0.635 0.313,0.156 10 false *a 3.021,1.729 3.333,1.885 0.313,0.156 10 false *b 4.76,1.969 5.448,2.271 0.688,0.302 10 false DOWN 3.99,1.958 4.604,2.229 0.615,0.271 10 false UP 5.104,1.271 5.719,1.521 0.615,0.25 10 false GND 3.823,1.271 4.177,1.542 0.354,0.271 10 false B 4.385,0.656 5,0.854 0.615,0.198 10 false F12
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


OK:
Tester Connection Specified Condition

Click Location & Routing(F12)Location & Routing

Click Connector(F12)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

1.

Connect the positive (+) lead of the auxiliary battery to terminal F12-2 (B) and the negative (-) lead to terminal F12-1 (GND), and hold for 3 seconds or more.

2.

While terminals F12-2 (B) and F12-1 (GND) are connected, connect the negative (-) lead of the auxiliary battery to terminal F12-10 (UP).

3.

After disconnecting the negative (-) lead of the auxiliary battery from terminal F12-10 (UP), connect terminal F12-10 (UP) to the negative (-) lead of the auxiliary battery again within 1 second.


Motor gear rotates counterclockwise (UP)
1.

Connect the positive (+) lead of the auxiliary battery to terminal F12-2 (B) and the negative (-) lead to terminal F12-1 (GND), and hold for 3 seconds or more.

2.

While terminals F12-2 (B) and F12-1 (GND) are connected, connect the negative (-) lead of the auxiliary battery to terminal F12-7 (DOWN).

3.

After disconnecting the negative (-) lead of the auxiliary battery from terminal F12-7 (DOWN), connect terminal F12-7 (DOWN) to the negative (-) lead of the auxiliary battery again within 1 second.


Motor gear rotates clockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly LH.


Hide 85710E 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NOTICE:
·

Do not apply positive (+) auxiliary battery voltage to any terminals, except terminal F1-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION



a.

Check that the motor gear rotates smoothly as follows.

E444323C04
2.406,0.677 2.719,0.854 0.313,0.177 4.052,1.813 4.719,1.813 true 2.74,1.333 3.156,1.333 true 2.01,1.333 2.427,1.333 true 2.073,1.99 2.375,1.667 true 2.771,1.656 3.063,1.99 true 1.615,0.531 1.927,0.688 0.313,0.156 10 false *a 3.896,1.74 4.208,1.896 0.313,0.156 10 false *b 3.198,1.271 3.51,1.427 0.313,0.156 10 false GND 1.906,1.271 2.219,1.427 0.313,0.156 10 false B 2.927,2.021 3.365,2.219 0.438,0.198 10 false DOWN 1.979,2.01 2.417,2.208 0.438,0.198 10 false UP 2.479,0.698 2.792,0.896 0.313,0.198 10 false F1
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


OK:
Tester Connection Specified Condition

Click Location & Routing(F1)Location & Routing

Click Connector(F1)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

1.

Connect the positive (+) lead of the auxiliary battery to terminal F1-2 (B) and the negative (-) lead to terminal F1-1 (GND), and hold for 3 seconds or more.

2.

While terminals F1-2 (B) and F1-1 (GND) are connected, connect the negative (-) lead of the auxiliary battery to terminal F1-10 (UP).

3.

After disconnecting the negative (-) lead of the auxiliary battery from terminal F1-10 (UP), connect terminal F1-10 (UP) to the negative (-) lead of the auxiliary battery again within 1 second.


Motor gear rotates clockwise (UP)
1.

Connect the positive (+) lead of the auxiliary battery to terminal F1-2 (B) and the negative (-) lead to terminal F1-1 (GND), and hold for 3 seconds or more.

2.

While terminals F1-2 (B) and F1-1 (GND) are connected, connect the negative (-) lead of the auxiliary battery to terminal F1-7 (DOWN).

3.

After disconnecting the negative (-) lead of the auxiliary battery from terminal F1-7 (DOWN), connect terminal F1-7 (DOWN) to the negative (-) lead of the auxiliary battery again within 1 second.


Motor gear rotates counterclockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly RH.