Home › Vehicle Interior › LIGHTING (INT) › PERSONAL LIGHT
RM37H0E _58 Vehicle Interior _095306 LIGHTING (INT) _0448207 PERSONAL LIGHT G

LIGHTING (INT)  PERSONAL LIGHT  INSPECTION  


PROCEDURE

Hide 81260A 1.INSPECT MAP LIGHT ASSEMBLY

a.

Inspect the front map light.

i.
E394607C03
1.552,2.635 1.927,2.865 0.375,0.229 1.563,0.385 1.885,0.615 0.323,0.229 2.115,1.271 2.531,0.771 true 1.031,3.708 0.688,4.115 true 1.344,1.292 1.052,0.792 true 1.344,3.729 1.135,4.188 true 1.49,1.302 1.292,0.76 true 2.104,1.583 2.302,2.073 true 1.646,0.427 1.958,0.625 0.313,0.198 10 false H8 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 1.625,2.677 1.938,2.875 0.313,0.198 10 false H10 0.354,4.115 0.969,4.313 0.615,0.198 10 false GND9 2.552,0.625 3.167,0.823 0.615,0.198 10 false +B1 0.802,0.646 1.417,0.844 0.615,0.198 10 false CTY 0.948,4.229 1.563,4.427 0.615,0.198 10 false DOOR 1.156,0.594 1.771,0.792 0.615,0.198 10 false LILL 2.229,2.094 2.844,2.292 0.615,0.198 10 false ILLB
*a Component without harness connected
(Map Light Assembly)


Apply battery voltage to the connector and check the light illumination condition.

OK:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H8,H10)Location & Routing

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

Click Connector(H10)Body>No. 1 Roof Wire>Map Light Assembly

H8-4 (+B1) - Auxiliary battery positive (+)
H10-20 (GND9) - Auxiliary battery negative (-)
Map light switch LH ON Map light LH illuminates
Map light switch RH ON Map light RH illuminates


HINT:

The map light switch is a capacitive touch switch. Therefore, the illumination turns on or off each time the lens around the light emitting area is touched.


If the result is not as specified, replace the map light assembly.


ii.

Inspect the front dome light.

Apply battery voltage to the connector and check the light illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(H8)Location & Routing

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

H8-4 (+B1) - Auxiliary battery positive (+)
H8-9 (CTY) - Auxiliary battery negative (-)
Front dome light illuminates


If the result is not as specified, replace the map light assembly.


iii.

Inspect the door switch.

Apply battery voltage to the connector and check the light illumination condition.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H10)Location & Routing

Click Connector(H10)Body>No. 1 Roof Wire>Map Light Assembly

H10-18 (DOOR) - H10-20 (GND9) DOOR switch ON Below 1 Ω
H10-18 (DOOR) - H10-20 (GND9) DOOR switch OFF 10 kΩ or higher


If the result is not as specified, replace the map light assembly.


iv.

Inspect the night illumination.

Apply battery voltage to the connector and check the light illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(H8)Location & Routing

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

H8-16 (ILLB) - Auxiliary battery positive (+)
H8-8 (LILL) - Auxiliary battery negative (-)
Night Illumination illuminates


If the result is not as specified, replace the map light assembly.