Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR GLASS
RM37H0E _59 Vehicle Exterior _095308 MIRROR (EXT) _0448221 OUTER REAR VIEW MIRROR GLASS G

MIRROR (EXT)  OUTER REAR VIEW MIRROR GLASS  INSPECTION  


PROCEDURE

Hide 87961 1.INSPECT OUTER MIRROR LH

a.
B512430C02
0.75,1.25 1.75,1.25 true 0.74,0.771 1.74,0.771 true 0.646,0.708 0.802,0.906 0.156,0.198 10 true 1 0.635,1.167 0.792,1.365 0.156,0.198 10 true 2 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror LH)


Check the outer mirror heater operation.

i.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C (77°F) 8.5 to 11.5 Ω



ii.

If the result is not as specified, replace the outer mirror LH.



b.

Check the operation of the outer rear view mirror indicator.

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
B512432C05
1.854,0.604 2.271,0.604 true 1.167,0.583 1.583,0.583 true 2.323,0.542 2.938,0.74 0.615,0.198 10 false BSM+ 0.792,0.542 1.406,0.74 0.615,0.198 10 false BSM- 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror LH)


Apply 6 V dry-cell batteries to the terminals of the connector, and check the blind spot monitor indicator condition.

NOTICE:
·

Do not use rechargeable batteries as they may not output a voltage of 1.5 V.

·

Do not apply a voltage of more than 6 V.



OK:
Tester Connection Specified Condition
Positive (+) end of the 6 V dry-cell battery - 1(BSM+)
Negative (-) end of the 6 V dry-cell battery - 2(BSM-)
Outer rear view mirror indicator comes on



iii.

If the result is not as specified, replace the outer mirror LH.



Hide 87931 2.INSPECT OUTER MIRROR RH

a.
B512431C02
1.667,0.792 2.417,0.792 false 1.667,1.229 2.417,1.229 false 2.438,0.729 2.635,0.875 0.198,0.146 10 true 1 2.448,1.167 2.646,1.313 0.198,0.146 10 true 2 0.115,0.063 0.427,0.26 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror RH)


Check the outer mirror heater operation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C (77°F) 8.5 to 11.5 Ω



ii.

If the result is not as specified, replace the outer mirror RH.



b.

Check the operation of the outer rear view mirror indicator.

i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
B512433C04
1.885,0.615 2.385,0.615 true 1.052,0.604 1.552,0.604 true 2.427,0.563 3.042,0.76 0.615,0.198 10 false BSM+ 0.667,0.563 1.281,0.76 0.615,0.198 10 false BSM- 0.094,0.125 0.406,0.323 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror RH)


Apply 6 V dry-cell batteries to the terminals of the connector, and check the blind spot monitor indicator condition.

NOTICE:
·

Do not use rechargeable batteries as they may not output a voltage of 1.5 V.

·

Do not apply a voltage of more than 6 V.



OK:
Tester Connection Specified Condition
Positive (+) end of the 6 V dry-cell battery - 1(BSM+)
Negative (-) end of the 6 V dry-cell battery - 2(BSM-)
Outer rear view mirror indicator comes on



iii.

If the result is not as specified, replace the outer mirror RH.