Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448240 HEADLIGHT ASSEMBLY N

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·
E457431C01
2.26,1.281 2.823,1.49 true 0,0 0.313,0.198 0.313,0.198 10 false *a 2.885,1.448 3.198,1.646 0.313,0.198 10 true *a
*a Center Mark


If it is not possible to correctly adjust the headlight aim, check the headlight assembly and headlight unit installation.



PROCEDURE

Hide 1.PREPARE VEHICLE FOR HEADLIGHT AIMING ADJUSTMENT

a.

Prepare the vehicle:

·

Make sure that there is no damage to the body around the headlights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the trunk and vehicle, ensuring that the spare tire, tools, and jack are in their original positions.

·

Sit a person of average weight (75 kg, 165 lb) in the driver seat.

·

Make sure that the vehicle is on a level surface.



Hide 2. PREPARE FOR HEADLIGHT AIMING (Using a headlight aim test machine)

a.

Adjust the headlight aim in accordance with the headlight aim test machine instructions.


Hide 3. PREPARE FOR HEADLIGHT AIMING (Using a screen)

a.
E382735C01
0.719,1.177 1.031,1.333 0.313,0.156 10 false *a 1.177,1.792 1.49,1.948 0.313,0.156 10 false *b
*a 90°
*b 25 m or 3 m (82 ft. to 9.84 ft.)


except China:

Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below the light from the headlights can be observed and those that cannot be observed.

·

Place the vehicle at a 90° angle to the wall.

·
E457431C01
2.26,1.281 2.823,1.49 true 0,0 0.313,0.198 0.313,0.198 10 false *a 2.885,1.448 3.198,1.646 0.313,0.198 10 true *a
*a Center Mark


Create a 25 m (82 ft.) distance between the vehicle (center marks of headlight) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.


NOTICE:

A distance of 25 m (82 ft.) between the vehicle (center marks of headlight) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft.) to allow for checking and adjustment of headlight aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration).



b.
E382735C01
0.719,1.177 1.031,1.333 0.313,0.156 10 false *a 1.177,1.792 1.49,1.948 0.313,0.156 10 false *b
*a 90°
*b 10 m or 3 m (32.8 ft. to 9.84 ft.)


for China:

Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below the light from the headlights can be observed and those that cannot be observed.

·

Place the vehicle at a 90° angle to the wall.

·
E457431C01
2.26,1.281 2.823,1.49 true 0,0 0.313,0.198 0.313,0.198 10 false *a 2.885,1.448 3.198,1.646 0.313,0.198 10 true *a
*a Center Mark


Create a 10 m (32.8 ft.) distance between the vehicle (center marks of headlight) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.


NOTICE:

A distance of 10 m (32.8 ft.) between the vehicle (center marks of headlight) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft.) to allow for checking and adjustment of headlight aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration).



c.

Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.


d.

Draw a vertical line down the center of the screen (V line).


e.

except China:

Set the screen as shown in the illustration.

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.



E382736E02
0.896,0.885 0.896,0.583 0.896,0.583 1.146,0.583 true 0.896,1.49 0.896,1.792 0.896,1.792 1.146,1.792 true 4.333,0.885 4.333,0.583 4.333,0.583 4.583,0.583 true 4.333,1.5 4.333,1.802 4.333,1.802 4.583,1.802 true 0.958,0.052 3.177,0.271 2.219,0.219 12 false Alignment distance is 25 m: 4.385,0.052 6.604,0.271 2.219,0.219 12 false Alignment distance is 3 m: 1.208,0.49 1.99,0.698 0.781,0.208 10 false V RH Line 4.646,0.49 5.427,0.698 0.781,0.208 10 false V RH Line 1.208,1.698 1.99,1.906 0.781,0.208 10 false V LH Line 4.656,1.719 5.438,1.927 0.781,0.208 10 false V LH Line 1.219,0.927 1.677,1.125 0.458,0.198 10 false 90° 4.646,0.927 5.104,1.125 0.458,0.198 10 false 90° 1.229,3.01 1.688,3.208 0.458,0.198 10 false 90° 4.667,3.01 5.125,3.208 0.458,0.198 10 false 90° 0.26,2.833 1.177,3.031 0.917,0.198 10 false H Line 3.708,2.833 4.625,3.031 0.917,0.198 10 false H Line 3.208,1.104 4.125,1.302 0.917,0.198 10 false V Line 6.646,1.104 7.094,1.323 0.448,0.219 10 false V Line 1.417,3.448 2.031,3.646 0.615,0.198 10 false 25 m 4.917,3.438 5.531,3.635 0.615,0.198 10 false 3 m


f.

for China:

Set the screen as shown in the illustration.

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.



E382736E03
0.896,0.885 0.896,0.583 0.896,0.583 1.146,0.583 true 0.896,1.49 0.896,1.792 0.896,1.792 1.146,1.792 true 4.333,0.885 4.333,0.583 4.333,0.583 4.583,0.583 true 4.333,1.5 4.333,1.802 4.333,1.802 4.583,1.802 true 0.958,0.052 3.177,0.271 2.219,0.219 12 false Alignment distance is 10 m: 4.385,0.052 6.604,0.271 2.219,0.219 12 false Alignment distance is 3 m: 1.208,0.49 1.99,0.698 0.781,0.208 10 false V RH Line 4.646,0.49 5.427,0.698 0.781,0.208 10 false V RH Line 1.208,1.698 1.99,1.906 0.781,0.208 10 false V LH Line 4.656,1.719 5.438,1.927 0.781,0.208 10 false V LH Line 1.219,0.927 1.677,1.125 0.458,0.198 10 false 90° 4.646,0.927 5.104,1.125 0.458,0.198 10 false 90° 1.229,3.01 1.688,3.208 0.458,0.198 10 false 90° 4.667,3.01 5.125,3.208 0.458,0.198 10 false 90° 0.26,2.833 1.177,3.031 0.917,0.198 10 false H Line 3.708,2.833 4.625,3.031 0.917,0.198 10 false H Line 3.208,1.104 4.125,1.302 0.917,0.198 10 false V Line 6.646,1.104 7.094,1.323 0.448,0.219 10 false V Line 1.417,3.448 2.031,3.646 0.615,0.198 10 false 25 m 4.917,3.438 5.531,3.635 0.615,0.198 10 false 3 m


g.
E257183C18
1.17,0.275 1.331,0.419 0.161,0.143 10 *a 1.823,0.275 1.984,0.419 0.161,0.143 10 *b 2.446,0.275 2.607,0.419 0.161,0.143 10 *c 2.936,0.851 3.097,0.994 0.161,0.143 10 *d 0.547,1.698 0.708,1.841 0.161,0.143 10 *e
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground


Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

HINT:
E457431C01
2.26,1.281 2.823,1.49 true 0,0 0.313,0.198 0.313,0.198 10 false *a 2.885,1.448 3.198,1.646 0.313,0.198 10 true *a
*a Center Mark


·

The base lines differ for "low beam inspection" and "high beam inspection".

·

Mark the headlight assembly center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight unit as the center mark.



i.

H Line (Headlight height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight center marks.


ii.

V LH Line and V RH Line (Center mark position of left-hand (LH) and right-hand (RH) headlights):

Draw 2 vertical lines so that they intersect the H line at each center mark (aligned with the center mark of the headlight).



Hide 4.INSPECT HEADLIGHT AIMING

a.

Cover the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming.

NOTICE:

Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.



b.

Start the engine.


c.

Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

The illustration is for LHD vehicles. RHD vehicles are the opposite of the illustration.

·

If the alignment distance is 25 m (82 ft.):

The low beam cutoff line should be within 83 mm (3.27 in.) and 37.5 cm (1.23 ft.) below the H line as well as 249 mm (9.80 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The low beam cutoff line should be within 10 mm (0.394 in.) and 45 mm (1.77 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 25 m (82 ft.):

The horizontal line of the preferred low beam cutoff line is 249 mm (9.80 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

E231280E20
1.031,1.458 0.552,1.938 false 1.781,1.427 2.083,0.615 true 2.083,0.615 2.198,0.615 false 4.031,1.865 4.531,1.448 false 5.24,1.396 5.542,0.583 true 5.542,0.583 5.656,0.583 false 4.271,0.063 6.396,0.406 2.125,0.344 12 false Alignment distance is 3 m: 0.771,0.063 2.958,0.406 2.188,0.344 12 false Alignment distance is 25 m: 1.042,2.344 2.542,2.677 1.5,0.333 10 false V LH Line or V RH Line 4.521,2.292 6.021,2.625 1.5,0.333 10 false V LH Line or V RH Line 0.198,1.969 0.938,2.406 0.74,0.438 10 false Preferred Cutoff Line 0.167,1.063 0.635,1.375 0.469,0.313 10 false H Line 3.646,1.042 4.115,1.354 0.469,0.313 10 false H Line 0.125,1.51 0.719,1.844 0.594,0.333 10 false 249 mm 1.146,0.875 1.677,1.208 0.531,0.333 10 false 83 mm 1.135,1.802 1.688,2.135 0.552,0.333 10 false 249 mm 2.938,1.323 3.469,1.656 0.531,0.333 10 false 375 mm 3.656,1.5 4.229,1.833 0.573,0.333 10 false 30 mm 4.635,0.875 5.125,1.208 0.49,0.333 10 false 10 mm 5.323,1.792 5.813,2.125 0.49,0.333 10 false 30 mm 4.719,1.771 5.208,2.104 0.49,0.333 10 false 30 mm 6.417,1.281 6.885,1.615 0.469,0.333 10 false 45 mm 3.625,1.875 4.365,2.51 0.74,0.635 10 false Preferred Cutoff Line 1.875,1.813 2.427,2.146 0.552,0.333 10 false 249 mm 2.229,0.531 2.76,0.823 0.531,0.292 10 false Point A 5.708,0.49 6.24,0.781 0.531,0.292 10 false Point A




d.

Turn on the high beams and check if the center of intensity for each high beam matches the preferred center of the intensity in the illustration.

HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If the alignment distance is 25 m (82 ft.):

The high beam center of intensity should be within 175 mm (6.88 in.) above and 249 mm (9.80 in.) below the H line as well as 497 mm (1.63 ft.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The high beam center of intensity should be within 21 mm (0.82 in.) above and 30 mm (1.18 in.) below the H line as well as 60 mm (2.36 in.) left or right of the V LH or V RH line.

E261529E01
5.052,1.354 5.51,0.615 5.51,0.615 5.729,0.615 true 1.656,1.354 2.115,0.615 2.115,0.615 2.333,0.615 true 0.75,0.115 2.906,0.448 2.156,0.333 12 Alignment distance is 25 m: 4.135,0.104 6.292,0.438 2.156,0.333 12 Alignment distance is 3 m: 4.365,2.375 5.854,2.688 1.49,0.313 10 V LH Line or V RH Line 0.969,2.385 2.458,2.698 1.49,0.313 10 V LH Line or V RH Line 5.76,0.531 7.052,0.927 1.292,0.396 10 Center of Intensity 2.375,0.531 3.667,0.927 1.292,0.396 10 Center of Intensity 3.573,1.271 4.052,1.615 0.479,0.344 10 H Line 0.188,1.281 0.667,1.625 0.479,0.344 10 H Line 1.75,2.01 2.344,2.271 0.594,0.26 10 497 mm 1.031,2.01 1.625,2.271 0.594,0.26 10 497 mm 2.802,1.813 3.396,2.073 0.594,0.26 10 249 mm 2.792,0.917 3.385,1.177 0.594,0.26 10 175 mm 4.448,2 5.042,2.26 0.594,0.26 10 60 mm 5.177,1.99 5.771,2.25 0.594,0.26 10 60 mm 6.177,1.823 6.771,2.083 0.594,0.26 10 30 mm 6.177,0.917 6.771,1.177 0.594,0.26 10 21 mm




Hide 5.ADJUST HEADLIGHT AIMING

a.
E457432C03
0.948,2.688 0.625,3.146 true 1.438,3.188 1.542,2.729 true 0.552,3.167 0.771,3.354 0.219,0.188 10 false *b 1.281,3.177 1.5,3.365 0.219,0.188 10 false *a
*a Vertical Aiming Screw
*b Horizontal Aiming Screw


Using a screwdriver, adjust the aim.

Adjust the aim of each headlight so that it is within the specified range by turning each aiming screw with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it, and then retighten it so that the final turn of the screw is in the clockwise direction.


HINT:
·

The low beam and high beam headlight are a unit. Adjusting the aim on the low beam to the correct position should also result in the high beam adjustment being correct.

·
E457431C01
2.26,1.281 2.823,1.49 true 0,0 0.313,0.198 0.313,0.198 10 false *a 2.885,1.448 3.198,1.646 0.313,0.198 10 true *a
*a Center Mark


If it is not possible to correctly adjust the headlight aim, check the headlight assembly and headlight unit installation.

·

The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise. The headlight aim moves right when turning the horizontal aiming screw clockwise, and moves left when turning the horizontal aiming screw counterclockwise.