Home › Vehicle Exterior › LIGHTING (EXT) › REAR COMBINATION LIGHT ASSEMBLY
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448243 REAR COMBINATION LIGHT ASSEMBLY G

LIGHTING (EXT)  REAR COMBINATION LIGHT ASSEMBLY  INSPECTION  


PROCEDURE

Hide 81565D 1.INSPECT REAR COMBINATION LIGHT CORD LH

a.

Inspect the rear combination light cord LH.

i.

Measure the resistance according to the value(s) in the table below.

E457649C01
5.781,0.479 6.177,0.75 0.396,0.271 3.521,0.469 3.917,0.74 0.396,0.271 1.24,0.417 1.635,0.688 0.396,0.271 5.354,2.01 5.802,1.75 false 6.156,1.448 6.531,1.25 false 6.146,1.708 6.5,2 false 5.323,1.25 5.802,1.458 false 5.854,0.542 6.313,0.74 0.458,0.198 10 false G73 1.385,0.51 1.844,0.708 0.458,0.198 10 false A 3.656,0.542 4.115,0.74 0.458,0.198 10 false B 5.198,1.167 5.354,1.365 0.156,0.198 10 false B 6.583,1.167 7.083,1.396 0.5,0.229 10 false STP 5.052,1.969 5.552,2.198 0.5,0.229 10 false TRN 6.594,1.979 6.75,2.177 0.156,0.198 10 false E 0.156,0.094 0.615,0.292 0.458,0.198 10 false *a
*a Component without harness connected
(Rear Combination Light Cord LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G73)Location & Routing

Click Connector(G73)Body>Floor Wire / No. 3 Floor Wire>Rear Combination Light LH

A1 - G73-1(B) Always Below 1 Ω
A2 - G73-2(STP) Always Below 1 Ω
B2 - G73-3(TRN) Always Below 1 Ω
A3 - G73-4(E)
B1 - G73-4(E)
Always Below 1 Ω


HINT:

If the result is not as specified, replace the rear combination light cord LH.




Hide 81555G 2.INSPECT REAR COMBINATION LIGHT CORD RH

a.

Inspect the rear combination light cord RH.

i.

Measure the resistance according to the value(s) in the table below.

E457649C03
5.781,0.479 6.177,0.75 0.396,0.271 3.521,0.469 3.917,0.74 0.396,0.271 1.24,0.417 1.635,0.688 0.396,0.271 5.354,2.01 5.802,1.75 false 6.156,1.448 6.531,1.25 false 6.146,1.708 6.5,2 false 5.323,1.25 5.802,1.458 false 5.854,0.542 6.313,0.74 0.458,0.198 10 false G72 1.385,0.51 1.844,0.708 0.458,0.198 10 false A 3.656,0.542 4.115,0.74 0.458,0.198 10 false B 5.198,1.167 5.354,1.365 0.156,0.198 10 false B 6.583,1.167 7.083,1.396 0.5,0.229 10 false STP 5.052,1.969 5.552,2.198 0.5,0.229 10 false TRN 6.594,1.979 6.75,2.177 0.156,0.198 10 false E 0.156,0.094 0.615,0.292 0.458,0.198 10 false *a
*a Component without harness connected
(Rear Combination Light Cord RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G72)Location & Routing

Click Connector(G72)Body>Floor Wire / No. 3 Floor Wire>Rear Combination Light RH

A1 - G72-1(B) Always Below 1 Ω
A2 - G72-2(STP) Always Below 1 Ω
B2 - G72-3(TRN) Always Below 1 Ω
A3 - G72-4(E)
B1 - G72-4(E)
Always Below 1 Ω


HINT:

If the result is not as specified, replace the rear combination light cord RH.




Hide 81536B 3.INSPECT REAR TURN SIGNAL LIGHT LED (for LH Side)

a.

Check the illumination.

i.
E457648C01
0.083,0.094 0.396,0.25 0.313,0.156 10 false *a
*a Component without harness connected
(Rear Turn Signal Light LED)


Apply auxiliary battery voltage to the rear turn signal light LED and check that the lights illuminate.

OK:
Connection Specified Condition
Auxiliary battery positive (+) → Terminal 2
Auxiliary battery negative (-) → Terminal 1
Rear turn signal light LED illuminates


HINT:

If the result is not as specified, replace the rear turn signal light LED.




Hide 81536B 4.INSPECT REAR TURN SIGNAL LIGHT LED (for RH Side)

a.

Check the illumination.

i.
E457648C01
0.083,0.094 0.396,0.25 0.313,0.156 10 false *a
*a Component without harness connected
(Rear Turn Signal Light LED)


Apply auxiliary battery voltage to the rear turn signal light LED and check that the lights illuminate.

OK:
Connection Specified Condition
Auxiliary battery positive (+) → Terminal 2
Auxiliary battery negative (-) → Terminal 1
Rear turn signal light LED illuminates


HINT:

If the result is not as specified, replace the rear turn signal light LED.




Hide 81561D 5.INSPECT REAR COMBINATION LIGHT LENS AND BODY LH

a.

Check the illumination.

i.
E457647C01
0.083,0.094 0.396,0.25 0.313,0.156 10 false *a
*a Component without harness connected
(Rear Combination Light Lens and Body LH)


Apply auxiliary battery voltage to the rear combination light lens and body LH and check that the lights illuminate.

OK:
Connection Specified Condition
Auxiliary battery positive (+) → Terminal 1
Auxiliary battery positive (+) → Terminal 2
Auxiliary battery negative (-) → Terminal 3
Rear combination light lens and body LH illuminates


HINT:

If the result is not as specified, replace the rear combination light lens and body LH.




Hide 81551D 6.INSPECT REAR COMBINATION LIGHT LENS AND BODY RH

a.

Check the illumination.

i.
E457647C01
0.083,0.094 0.396,0.25 0.313,0.156 10 false *a
*a Component without harness connected
(Rear Combination Light Lens and Body RH)


Apply auxiliary battery voltage to the rear combination light lens and body RH and check that the lights illuminate.

OK:
Connection Specified Condition
Auxiliary battery positive (+) → Terminal 1
Auxiliary battery positive (+) → Terminal 2
Auxiliary battery negative (-) → Terminal 3
Rear combination light lens and body RH illuminates


HINT:

If the result is not as specified, replace the rear combination light lens and body RH.