Home › Vehicle Exterior › LIGHTING (EXT) › REAR LIGHT ASSEMBLY
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448244 REAR LIGHT ASSEMBLY G

LIGHTING (EXT)  REAR LIGHT ASSEMBLY  INSPECTION  


PROCEDURE

Hide 81595 1.INSPECT REAR LIGHT SOCKET AND WIRE LH

a.

Inspect the rear light socket and wire LH.

i.

Measure the resistance according to the value(s) in the table below.

E457669C01
4.896,0.146 5.219,0.323 0.323,0.177 2.063,0.375 2.385,0.563 0.323,0.188 5.208,1.198 5.802,1.458 true 5.167,1.01 5.76,0.844 true 4.406,0.885 4.927,1.021 true 5.833,0.771 6.146,0.969 0.313,0.198 10 false B 2.188,0.396 2.344,0.594 0.156,0.198 10 false A 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 5.833,1.406 6.146,1.604 0.313,0.198 10 false E 4.271,0.802 4.583,1 0.313,0.198 10 false B 4.99,0.177 5.302,0.375 0.313,0.198 10 false K6
*a Component without harness connected
(Rear Light Socket and Wire LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K6)Location & Routing

Click Connector(K6)Body>No. 1 Back Door Wire>Rear Light Assembly LH

A2 - K6-1(B) Always Below 1 Ω
A4 - K6-2(B) Always Below 1 Ω
A1 - K6-4(E) Always Below 1 Ω


HINT:

If the result is not as specified, replace the rear light socket and wire LH.




Hide 81585C 2.INSPECT REAR LIGHT SOCKET AND WIRE RH

a.

Inspect the rear light socket and wire RH.

i.

Measure the resistance according to the value(s) in the table below.

E457669C02
4.896,0.146 5.219,0.323 0.323,0.177 2.063,0.375 2.385,0.563 0.323,0.188 5.208,1.198 5.802,1.458 true 5.167,1.01 5.76,0.844 true 4.406,0.885 4.927,1.021 true 5.833,0.771 6.146,0.969 0.313,0.198 10 false B 2.188,0.396 2.344,0.594 0.156,0.198 10 false A 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 5.833,1.406 6.146,1.604 0.313,0.198 10 false E 4.271,0.802 4.583,1 0.313,0.198 10 false B 4.948,0.177 5.385,0.375 0.438,0.198 10 false K10
*a Component without harness connected
(Rear Light Socket and Wire RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K10)Location & Routing

Click Connector(K10)Body>No. 1 Back Door Wire>Rear Light Assembly RH

A2 - K10-1(B) Always Below 1 Ω
A4 - K10-2(B) Always Below 1 Ω
A1 - K10-4(E) Always Below 1 Ω


HINT:

If the result is not as specified, replace the rear light socket and wire RH.




Hide 81590A 3.INSPECT REAR LIGHT ASSEMBLY LH

a.

Check the illumination.

i.
E457670C01
0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component without harness connected
(Rear Light Assembly LH)


Apply auxiliary battery voltage to the rear light assembly LH and check that the lights illuminate.

OK:
Tester Connection Specified Condition
Auxiliary battery positive (+) - 2
Auxiliary battery positive (+) - 1
Tail light (rear light assembly LH) illuminates
Auxiliary battery positive (+) - 4
Auxiliary battery positive (+) - 1
Back up light (rear light assembly LH) illuminates


HINT:

If the result is not as specified, replace the rear light assembly LH.




Hide 81580D 4.INSPECT REAR LIGHT ASSEMBLY RH

a.

Check the illumination.

i.
E457670C01
0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component without harness connected
(Rear Light Assembly RH)


Apply auxiliary battery voltage to the rear light assembly RH and check that the lights illuminate.

OK:
Tester Connection Specified Condition
Auxiliary battery positive (+) - 2
Auxiliary battery positive (+) - 1
Tail light (rear light assembly RH) illuminates
Auxiliary battery positive (+) - 4
Auxiliary battery positive (+) - 1
Back up light (rear light assembly RH) illuminates


HINT:

If the result is not as specified, replace the rear light assembly RH.