Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT DIMMER SWITCH
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448247 HEADLIGHT DIMMER SWITCH G

LIGHTING (EXT)  HEADLIGHT DIMMER SWITCH  INSPECTION  


PROCEDURE

Hide 84329 1.INSPECT TURN SIGNAL SWITCH (for Headlight Dimmer Switch LH Side Type)

a.

Inspect the light control switch.

i.
E450695C47
1.625,0.125 1.979,0.354 0.354,0.229 1.417,1.438 1.302,1.865 true 2.208,1.438 2.333,1.865 true 1.333,0.344 1.594,1.021 true 2.479,0.344 2.208,1.021 true 1.802,1.438 1.729,1.875 true 2.531,0.229 3.01,0.406 0.479,0.177 10 false L_OFF 1.635,1.906 1.948,2.104 0.313,0.198 10 false EL 1.208,0.24 1.438,0.427 0.229,0.188 10 false H 2.323,1.896 2.531,2.073 0.208,0.177 10 false A 1.24,1.885 1.406,2.063 0.167,0.177 10 false T 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a 1.708,0.156 2.021,0.354 0.313,0.198 10 false z3
*a Component without harness connected
(Turn Signal Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

*1: w/ OFF Switch

Click Location & Routing(z3)Location & Routing

Click Connector(z3)Instrument Panel>other>Steering Wheel Switch Housing , Turn Signal Switch

z3-2 (L_OFF) - z3-12 (EL) Light control switch OFF*1 Below 1 Ω
z3-10 (A) - z3-12 (EL) Light control switch AUTO position Below 1 Ω
z3-14 (T) - z3-12 (EL) Light control switch TAIL position Below 1 Ω
z3-5 (H) - z3-12 (EL) Light control switch HEAD position Below 1 Ω


HINT:

If the result is not as specified, replace the turn signal switch.




b.
E450695C48
1.563,0.167 1.896,0.385 0.333,0.219 2.708,0.406 2.438,1.031 true 1.167,0.344 1.427,1.021 true 1.823,1.427 1.979,1.938 true 1.958,1.969 2.271,2.146 0.313,0.177 10 false EL 0.948,0.25 1.208,0.406 0.26,0.156 10 false HF 2.76,0.313 3.031,0.479 0.271,0.167 10 false HU 0.115,0.135 0.427,0.292 0.313,0.156 10 false *a 1.646,0.188 1.958,0.385 0.313,0.198 10 false z3
*a Component without harness connected
(Turn Signal Switch)


Inspect the headlight dimmer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(z3)Location & Routing

Click Connector(z3)Instrument Panel>other>Steering Wheel Switch Housing , Turn Signal Switch

z3-6 (HF) - z3-12 (EL) Headlight dimmer switch flash position Below 1 Ω
z3-1 (HU) - z3-12 (EL) Headlight dimmer switch high position Below 1 Ω


HINT:

If the result is not as specified, replace the turn signal switch.




c.
E450695C49
1.49,0.167 1.844,0.427 0.354,0.26 2.25,0.354 2.01,1.01 true 1.802,1.427 1.708,1.844 true 2.021,1.427 2.177,1.865 true 2.656,1.854 2.438,1.427 true 2.313,0.26 2.563,0.406 0.25,0.146 10 false TL 1.615,1.885 1.927,2.083 0.313,0.198 10 false EL 2.104,1.896 2.417,2.073 0.313,0.177 10 false CR 2.615,1.906 2.875,2.083 0.26,0.177 10 false TR 0.094,0.104 0.406,0.26 0.313,0.156 10 false *a 1.573,0.219 1.885,0.417 0.313,0.198 10 false z3
*a Component without harness connected
(Turn Signal Switch)


Inspect the turn signal light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(z3)Location & Routing

Click Connector(z3)Instrument Panel>other>Steering Wheel Switch Housing , Turn Signal Switch

z3-9 (TR) - z3-12 (EL) Turn signal switch neutral position 10 kΩ or higher
z3-3 (TL) - z3-12 (EL) Turn signal switch neutral position 10 kΩ or higher
z3-9 (TR) - z3-12 (EL) Turn signal switch right turn position
(self cancel condition)
Below 1 Ω
z3-9 (TR) - z3-12 (EL) Turn signal switch right turn position
(cancel ratchet operation condition)
Below 1 Ω
z3-9 (TR) - z3-11 (CR) Turn signal switch right turn position
(cancel ratchet operation condition)
Below 1 Ω
z3-11 (CR) - z3-12 (EL) Turn signal switch right turn position
(cancel ratchet operation condition)
Below 1 Ω
z3-3 (TL) - z3-12 (EL) Turn signal switch left turn position
(self cancel condition)
Below 1 Ω
z3-3 (TL) - z3-12 (EL) Turn signal switch left turn position
(cancel ratchet operation condition)
Below 1 Ω
z3-3 (TL) - z3-11 (CR) Turn signal switch left turn position
(cancel ratchet operation condition)
Below 1 Ω
z3-11 (CR) - z3-12 (EL) Turn signal switch left turn position
(cancel ratchet operation condition)
Below 1 Ω


HINT:
·

If the result is not as specified, replace the turn signal switch.

·

The self cancel condition indicates when the turn signal switch returns to the neutral position after releasing your hand from the switch (switch is operated within 6.3°).

·

The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even after releasing your hand (switch operation is 10.5°).





d.
E450695C50
1.521,0.156 1.875,0.365 0.354,0.208 1.823,1.438 1.906,1.885 true 1.49,1.917 1.615,1.448 true 1.417,1.958 1.635,2.177 0.219,0.219 10 false B 1.844,1.927 2.104,2.146 0.26,0.219 10 false EL 0.125,0.115 0.438,0.271 0.313,0.156 10 false *a 1.615,0.188 1.927,0.385 0.313,0.198 10 false z3
*a Component without harness connected
(Turn Signal Switch)


Inspect the rear fog light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(z3)Location & Routing

Click Connector(z3)Instrument Panel>other>Steering Wheel Switch Housing , Turn Signal Switch

z3-13 (B) - z3-12 (EL) Rear fog light switch off 10 kΩ or higher
z3-13 (B) - z3-12 (EL) Rear fog light switch on Below 1 Ω


If the result is not as specified, replace the turn signal switch.



Hide 84329 2.INSTALL TURN SIGNAL SWITCH (for Headlight Dimmer Switch RH Side Type)

a.

Inspect the light control switch.

i.
E450695C51
1.552,0.104 1.896,0.323 0.344,0.219 1.375,0.344 1.635,1.021 true 0.969,0.333 1.229,1.01 true 2.104,0.375 2.01,1.01 true 1.813,1.438 1.99,1.948 true 1.281,0.198 1.594,0.396 0.313,0.198 10 false EL 1.979,1.99 2.208,2.177 0.229,0.188 10 false H 0.917,0.188 1.125,0.365 0.208,0.177 10 false A 2.073,0.229 2.24,0.406 0.167,0.177 10 false T 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a 1.635,0.125 1.948,0.323 0.313,0.198 10 false z3
*a Component without harness connected
(Turn Signal Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(z3)Location & Routing

Click Connector(z3)Instrument Panel>other>Steering Wheel Switch Housing , Turn Signal Switch

z3-7(A) - z3-5(EL) Light control switch AUTO position Below 1 Ω
z3-3(T) - z3-5(EL) Light control switch TAIL position Below 1 Ω
z3-12(H) - z3-5(EL) Light control switch HEAD position Below 1 Ω


HINT:

If the result is not as specified, replace the turn signal switch.




b.

Inspect the headlight dimmer switch.

i.
E450695C52
1.583,0.104 1.927,0.302 0.344,0.198 1.042,1.427 0.958,1.938 true 1.354,0.354 1.615,1.031 true 2.021,1.427 2.177,1.938 true 1.25,0.198 1.563,0.396 0.313,0.198 10 false EL 2.156,1.979 2.417,2.135 0.26,0.156 10 false HF 0.865,1.979 1.135,2.146 0.271,0.167 10 false HU 0.115,0.135 0.427,0.292 0.313,0.156 10 false *a 1.677,0.125 1.99,0.323 0.313,0.198 10 false z3
*a Component without harness connected
(Turn Signal Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(z3)Location & Routing

Click Connector(z3)Instrument Panel>other>Steering Wheel Switch Housing , Turn Signal Switch

z3-11(HF) - z3-5(EL) Headlight dimmer switch flash position Below 1 Ω
z3-16(HU) - z3-5(EL) Headlight dimmer switch high position Below 1 Ω


HINT:

If the result is not as specified, replace the turn signal switch.




c.

Inspect the turn signal light switch.

i.
E450695C53
1.521,0.125 1.854,0.365 0.333,0.24 1.219,0.354 1.406,1.021 true 2.125,0.354 1.604,1.021 true 1.427,1.427 1.323,1.938 true 1.031,1.021 0.729,0.365 true 1.229,1.979 1.479,2.125 0.25,0.146 10 false TL 2.167,0.177 2.479,0.375 0.313,0.198 10 false EL 1.094,0.208 1.406,0.385 0.313,0.177 10 false CR 0.625,0.219 0.885,0.396 0.26,0.177 10 false TR 0.094,0.104 0.406,0.26 0.313,0.156 10 false *a 1.594,0.156 1.906,0.354 0.313,0.198 10 false z3
*a Component without harness connected
(Turn Signal Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(z3)Location & Routing

Click Connector(z3)Instrument Panel>other>Steering Wheel Switch Housing , Turn Signal Switch

z3-8(TR) - z3-5(EL) Turn signal switch neutral position 10 kΩ or higher
z3-14(TL) - z3-5(EL) Turn signal switch neutral position 10 kΩ or higher
z3-8(TR) - z3-5(EL) Turn signal switch right turn position
(self cancel condition)
Below 1 Ω
z3-8(TR) - z3-5(EL) Turn signal switch right turn position
(cancel ratchet operation condition)
Below 1 Ω
z3-8(TR) - z3-6(CR) Turn signal switch right turn position
(cancel ratchet operation condition)
Below 1 Ω
z3-6(CR) - z3-5(EL) Turn signal switch right turn position
(cancel ratchet operation condition)
Below 1 Ω
z3-14(TL) - z3-5(EL) Turn signal switch left turn position
(self cancel condition)
Below 1 Ω
z3-14(TL) - z3-5(EL) Turn signal switch left turn position
(cancel ratchet operation condition)
Below 1 Ω
z3-14(TL) - z3-6(CR) Turn signal switch left turn position
(cancel ratchet operation condition)
Below 1 Ω
z3-6(CR) - z3-5(EL) Turn signal switch left turn position
(cancel ratchet operation condition)
Below 1 Ω


HINT:
·

If the result is not as specified, replace the turn signal switch.

·

The self cancel condition indicates when the turn signal switch returns to the neutral position after releasing your hand from the switch (switch is operated within 6.3°).

·

The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even after releasing your hand (switch operation is 10.5°).





d.

Inspect the rear fog light switch.

i.
E450695C54
1.531,0.073 1.854,0.271 0.323,0.198 1.969,0.344 1.792,1.031 true 1.583,1.021 1.396,0.406 true 1.313,0.25 1.625,0.448 0.313,0.198 10 false EL 1.958,0.177 2.219,0.396 0.26,0.219 10 false B 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.615,0.094 1.927,0.292 0.313,0.198 10 false z3
*a Component without harness connected
(Turn Signal Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(z3)Location & Routing

Click Connector(z3)Instrument Panel>other>Steering Wheel Switch Housing , Turn Signal Switch

z3-4(B) - z3-5(EL) Rear fog light switch off 10 kΩ or higher
z3-4(B) - z3-5(EL) Rear fog light switch on Below 1 Ω


HINT:

If the result is not as specified, replace the turn signal switch.