Home › Vehicle Interior › METER / GAUGE / DISPLAY › TRIP SWITCH
RM37H0E _58 Vehicle Interior _095316 METER / GAUGE / DISPLAY _0448308 TRIP SWITCH G

METER / GAUGE / DISPLAY  TRIP SWITCH  INSPECTION  


PROCEDURE

Hide 84975 1.INSPECT TRIP SWITCH (for LHD)

a.
E457198C03
1.521,1.615 1.927,1.833 0.406,0.219 0.833,0.927 0.99,0.313 0.99,0.313 1.156,0.313 true 2.135,2.646 2.5,2.646 true 1.031,3.26 1.208,3.26 1.208,3.26 1.469,2.906 true 1.198,0.219 1.51,0.375 0.313,0.156 10 false *1 0.583,1.708 0.896,1.865 0.313,0.156 10 false *a 0.719,3.167 1.115,3.365 0.396,0.198 10 false A/B 1.625,1.646 1.938,1.802 0.313,0.156 10 false D7 2.563,2.583 2.875,2.74 0.313,0.156 10 false E
*1 ODO TRIP Switch
*a Component without harness connected
(Trip Switch)


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D7)Location & Routing

Click Connector(D7)Instrument Panel>Instrument Panel Wire>Trip Switch

D7-9 (A/B) - D7-1 (E) ODO/TRIP switch pressed Below 1 Ω
D7-9 (A/B) - D7-1 (E) ODO/TRIP switch not pressed 10 kΩ or higher


If the result is not as specified, replace the trip switch.



b.
E457198C04
1.51,1.625 1.896,1.854 0.385,0.229 0.958,2.865 1.26,2.865 true 2.156,2.875 2.458,2.875 true 0.521,1.823 0.833,1.979 0.313,0.156 10 false *a 0.667,2.813 1.281,3.01 0.615,0.198 10 false ILL+ 2.51,2.823 3.125,3.021 0.615,0.198 10 false ILL- 1.604,1.656 2.219,1.854 0.615,0.198 10 false D7
*a Component without harness connected
(Trip Switch)


Check illumination.

i.

Apply auxiliary battery voltage to the connector and check the light illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(D7)Location & Routing

Click Connector(D7)Instrument Panel>Instrument Panel Wire>Trip Switch

Auxiliary battery positive (+) → D7-10 (ILL+)
Auxiliary battery negative (-) → D7-6 (ILL-)
Illuminates


If the result is not as specified, replace the trip switch.



Hide 84975 2.INSPECT TRIP SWITCH (for RHD)

a.
E457193C07
1.521,1.615 1.927,1.833 0.406,0.219 2.583,0.927 2.74,0.313 2.74,0.313 2.906,0.313 true 2.135,2.646 2.5,2.646 true 1.031,3.26 1.208,3.26 1.208,3.26 1.469,2.906 true 2.979,0.24 3.292,0.396 0.313,0.156 10 false *1 0.583,1.708 0.896,1.865 0.313,0.156 10 false *a 0.719,3.167 1.115,3.365 0.396,0.198 10 false A/B 1.656,1.667 1.969,1.823 0.313,0.156 10 false D7 2.563,2.583 2.875,2.74 0.313,0.156 10 false E
*1 ODO TRIP Switch
*a Component without harness connected
(Trip Switch)


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D7)Location & Routing

Click Connector(D7)Instrument Panel>Instrument Panel Wire>Trip Switch

D7-9 (A/B) - D7-1 (E) ODO/TRIP switch pressed Below 1 Ω
D7-9 (A/B) - D7-1 (E) ODO/TRIP switch not pressed 10 kΩ or higher


If the result is not as specified, replace the trip switch.



b.
E457193C08
1.51,1.625 1.896,1.854 0.385,0.229 0.958,2.865 1.26,2.865 true 2.156,2.875 2.458,2.875 true 0.521,1.823 0.833,1.979 0.313,0.156 10 false *a 0.667,2.813 1.281,3.01 0.615,0.198 10 false ILL+ 2.51,2.823 3.125,3.021 0.615,0.198 10 false ILL- 1.635,1.677 2.25,1.875 0.615,0.198 10 false D7
*a Component without harness connected
(Trip Switch)


Check illumination.

i.

Apply auxiliary battery voltage to the connector and check the light illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(D7)Location & Routing

Click Connector(D7)Instrument Panel>Instrument Panel Wire>Trip Switch

Auxiliary battery positive (+) → D7-10 (ILL+)
Auxiliary battery negative (-) → D7-6 (ILL-)
Illuminates


If the result is not as specified, replace the trip switch.