Home › Vehicle Interior › METER / GAUGE / DISPLAY › HEADUP DISPLAY SWITCH
RM37H0E _58 Vehicle Interior _095316 METER / GAUGE / DISPLAY _0448314 HEADUP DISPLAY SWITCH G

METER / GAUGE / DISPLAY  HEADUP DISPLAY SWITCH  INSPECTION  


PROCEDURE

Hide 84975 1.INSPECT HEADUP DISPLAY SWITCH (TRIP SWITCH) (for LHD)

a.
E457198C01
1.521,1.615 1.927,1.833 0.406,0.219 2.49,0.938 2.698,0.24 2.698,0.24 2.948,0.24 true 0.917,2.208 1.052,2.208 1.052,2.208 1.458,2.552 true 2.552,2.208 2.396,2.208 2.396,2.208 1.896,2.552 true 2.99,0.135 3.302,0.292 0.313,0.156 10 false *1 0.583,1.708 0.896,1.865 0.313,0.156 10 false *a 0.688,2.146 1,2.302 0.313,0.156 10 false ILU 1.625,1.646 1.938,1.802 0.313,0.156 10 false D7 2.604,2.156 2.917,2.313 0.313,0.156 10 false CH
*1 HUD Switch
*a Component without harness connected
(Headup Display Switch (Trip Switch))


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D7)Location & Routing

Click Connector(D7)Instrument Panel>Instrument Panel Wire>Trip Switch

D7-4 (ILU) - D7-2 (CH) HUD switch pushed Below 1 Ω
D7-4 (ILU) - D7-2 (CH) HUD switch not pushed 10 kΩ or higher


If the result is not as specified, replace the headup display switch (trip switch) assembly.



b.
E457198C02
1.51,1.625 1.896,1.854 0.385,0.229 0.958,2.865 1.26,2.865 true 2.156,2.875 2.458,2.875 true 0.521,1.823 0.833,1.979 0.313,0.156 10 false *a 0.667,2.813 1.281,3.01 0.615,0.198 10 false ILL+ 2.51,2.823 3.125,3.021 0.615,0.198 10 false ILL- 1.604,1.656 2.219,1.854 0.615,0.198 10 false D7
*a Component without harness connected
(Headup Display Switch (Trip Switch))


Check illumination.

i.

Apply auxiliary battery voltage to the connector and check the light illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(D7)Location & Routing

Click Connector(D7)Instrument Panel>Instrument Panel Wire>Trip Switch

Auxiliary battery positive (+) - D7-10 (ILL+)
Auxiliary battery negative (-) - D7-6 (ILL-)
Illuminates


If the result is not as specified, replace the headup display switch (trip switch) assembly.



Hide 84975 2.INSPECT HEADUP DISPLAY SWITCH (TRIP SWITCH) (for RHD)

a.
E457193C09
1.521,1.615 1.927,1.833 0.406,0.219 0.885,0.948 1.094,0.25 1.094,0.25 1.344,0.25 true 0.917,2.208 1.052,2.208 1.052,2.208 1.458,2.552 true 2.552,2.208 2.396,2.208 2.396,2.208 1.896,2.552 true 1.406,0.188 1.719,0.344 0.313,0.156 10 false *1 0.583,1.708 0.896,1.865 0.313,0.156 10 false *a 0.688,2.146 1,2.302 0.313,0.156 10 false ILU 1.635,1.646 1.948,1.802 0.313,0.156 10 false D7 2.604,2.156 2.917,2.313 0.313,0.156 10 false CH
*1 HUD Switch
*a Component without harness connected
(Headup Display Switch (Trip Switch))


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D7)Location & Routing

Click Connector(D7)Instrument Panel>Instrument Panel Wire>Trip Switch

D7-4 (ILU) - D7-2 (CH) HUD switch pushed Below 1 Ω
HUD switch not pushed 10 kΩ or higher


If the result is not as specified, replace the headup display switch (trip switch) assembly.



b.
E457193C10
1.51,1.625 1.896,1.854 0.385,0.229 0.958,2.865 1.26,2.865 true 2.156,2.875 2.458,2.875 true 0.521,1.823 0.833,1.979 0.313,0.156 10 false *a 0.667,2.813 1.281,3.01 0.615,0.198 10 false ILL+ 2.51,2.823 3.125,3.021 0.615,0.198 10 false ILL- 1.615,1.656 2.229,1.854 0.615,0.198 10 false D7
*a Component without harness connected
(Headup Display Switch (Trip Switch))


Check illumination.

i.

Apply auxiliary battery voltage to the connector and check the light illumination condition.

OK:
Tester Connection Specified Condition

Click Location & Routing(D7)Location & Routing

Click Connector(D7)Instrument Panel>Instrument Panel Wire>Trip Switch

Auxiliary battery positive (+) - D7-10 (ILL+)
Auxiliary battery negative (-) - D7-6 (ILL-)
Illuminates


If the result is not as specified, replace the headup display switch (trip switch) assembly.