AUTOMATIC LIGHT CONTROL SYSTEM OPERATION CHECK
Make sure that the customize settings are set to default when performing the automatic light control system operation check.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS
Turn the ignition switch to ON.
Turn the light control switch to the AUTO position.
Cover the automatic light control sensor.
Check that the taillights and low beam headlights turn on.
Uncover the automatic light control sensor.
Check that the low beam headlights and taillights turn off.
LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK (except Driver Door-linked Auto Light Turn-off System)
When the light control switch is in the tail or head position
Turn the ignition switch to ON.
Turn the low beam headlights or high beam headlights on.
Turn the ignition switch off.
Check that the low beam headlights and high beam headlights turn off immediately.
The taillights and rear fog light remain on.
When the light control switch is in the AUTO position
Turn the ignition switch to ON.
Turn the taillights, low beam headlights, high beam headlights or rear fog light on.
Turn the ignition switch off.
Check that all of the lights turn off immediately.
LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK (for Driver Door-linked Auto Light Turn-off System)
Close all of the doors.
Turn the ignition switch to ON.
Turn the taillights, low beam headlights, high beam headlights and rear fog lights on.
Turn the ignition switch off.
Open the driver door.
Check that all of the lights turn off immediately.
LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK (w/ Delay Function)
When the taillights are on (low beam headlights are not on)
Close all of the doors.
Turn the ignition switch to ON.
Turn the taillights on.
Turn the ignition switch off.
Open the driver door.
Check that all of the lights turn off immediately.
When the low beam headlights are on
Close all of the doors.
Turn the ignition switch to ON.
Turn the low beam headlights on.
Turn the ignition switch off.
Open any of the doors.
Close the door.
Check that all of the lights turn off after 30 seconds (delay function).
Before the lights turn off, if the lock button on the key is pushed after all of the doors are locked, all of the lights will turn off immediately.
DAYTIME RUNNING LIGHT SYSTEM OPERATION CHECK
Make sure that the customize settings are set to default when performing the daytime running light system operation check.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS
Start the hybrid system.
Turn the light control switch to the AUTO position (with the low beam headlights not turned on via the automatic light control system).
Release the parking brake.
Check that the daytime running lights come on.
DOOR MIRROR FOOT LIGHT CONTROL OPERATION CHECK (w/ Door Mirror Footwell Light)
The operation and condition of this control are described below.
| Operation | Condition |
|---|---|
| Fade in and illuminate constantly | When any of the following conditions is met, the lights fade in and illuminate constantly:
·
A key is detected in the actuation area. ·
Any door is unlocked when the ignition switch is off and all of the doors are closed. |
| Illuminate for 15 seconds, and then fade out | When any of the following conditions is met, the lights illuminate for 15 seconds, and then fade out:
·
An actuation area-linked function is used.* ·
Any door is unlocked when the ignition switch is off and all of the doors are closed. |
| Fade out immediately | When the following condition is met, the lights fade out immediately:
·
The ignition switch is turned from off to ON. ·
A key is not detected in the actuation area. ·
All doors are locked when all doors are closed and any door is unlocked. |
*: When the lights are on, the lights fade out after approximately 3 seconds the key leaves the actuation areas around the doors.
EXTENDED HEADLIGHT LIGHTING OPERATION CHECK (w/ Extended Headlight Lighting)
Make sure that the customize settings are set to default when performing the extended headlight lighting system operation check.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS
Turn the ignition switch off.
Turn the light control switch to the AUTO position.
Pull the light control switch to flash the headlights once.
Check that the low beam headlights come on for approximately 30 seconds.