The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during headlight ECU sub-assembly LH removal/installation are shown below.
w/ Adaptive High Beam System:
If the steering sensor zero point calibration is not performed, the adaptive high beam system may not operate correctly.
A new headlight ECU sub-assembly LH cannot operate until the vehicle information is synchronized.
After replacing the headlight ECU sub-assembly LH, it is necessary to synchronize the vehicle information and performing initialization.
Even if the headlight ECU sub-assembly RH is replaced with a new one, synchronizing the vehicle information and performing initialization are not necessary.
Adjust the headlight aim after initializing the headlight ECU sub-assembly LH.
Vehicle information registration must be performed with the main body ECU (multiplex network body ECU) and EV control ECU connected via CAN communication.
1. SYNCHRONIZE VEHICLE INFORMATION
When using the GTS:
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check that the "Headlight System Unavailable Visit Your Dealer" warning message is displayed on the multi-information display.
w/ Adaptive High Beam System:
Enter the following menus: Body Electrical / AFS / Utility / ECU Information Sync.
| Tester Display |
|---|
| ECU Information Sync |
w/o Adaptive High Beam System:
Enter the following menus: Body Electrical / HL AutoLeveling / Utility / ECU Information Sync.
| Tester Display |
|---|
| ECU Information Sync |
Check the display on the GTS and press "Next".
Check that the "Headlight System Uninitialized Visit Your Dealer" warning message on the multi-information display continuously blinks 6 times at 2 Hz.
If the "Headlight System Unavailable Visit Your Dealer" warning message does not start blinking on the multi-information display after perform the procedure again.
If the "Headlight System Unavailable Visit Your Dealer" warning message changes from blinking to displayed on the multi-information display, the headlight ECU sub-assembly LH may be malfunctioning.
Press "Exit" and turn the ignition switch off.
After synchronizing the vehicle information, initialize the headlight ECU sub-assembly LH.
When not using the GTS:
Turn the ignition switch to ON.
Check that the "Headlight System Unavailable Visit Your Dealer" warning message is displayed on the multi-information display.
Using the headlight dimmer switch, turn the low beam headlights on and off 8 times within 20 seconds after turning the ignition switch to ON.
If the low beam headlights illuminate when the ignition switch is ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.
If this step cannot be completed within 20 seconds, turn the ignition switch off. Then, turn the ignition switch to ON and restart the procedure.
Check that the "Headlight System Unavailable Visit Your Dealer" warning message continuously blinks 6 times at 2 Hz on the multi-information display.
If the "Headlight System Unavailable Visit Your Dealer" warning message does not start blinking on the multi-information display after perform the procedure again.
If the "Headlight System Unavailable Visit Your Dealer" warning message changes from blinking to displayed on the multi-information display, turn the ignition switch off and then to ON. If "Headlight System Unavailable Visit Your Dealer" is displayed immediately after the ignition switch is turned to ON, the headlight ECU sub-assembly LH may be malfunctioning.
Turn the ignition switch off.
After synchronizing the vehicle information, initialize the headlight ECU sub-assembly LH.
81056A
2. HEADLIGHT ECU SUB-ASSEMBLY LH INITIALIZATION
Prepare vehicle for initialization
Unload the vehicle, ensuring that the spare tire, tools and jack are in their original positions.
Check that there are no occupants in the vehicle.
Stop the vehicle on a level surface and keep the vehicle height unchanged.
Check that rear height control sensor sub-assembly LH is connected correctly.
Check the "Headlight System Uninitialized Visit Your Dealer" on the multi-information display.
Turn the ignition switch to ON, and check the condition of the warning message on the multi-information display.
| Condition | Specified Condition |
|---|---|
| The headlight ECU sub-assembly LH has been replaced with a new one. | "Headlight System Uninitialized Visit Your Dealer" on the multi-information display continuously blinks 6 times at 2 Hz. |
| Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed. | "Headlight System Uninitialized Visit Your Dealer" is not displayed on the multi-information display. |
If the condition of the warning message is different than listed in the table above, the headlight ECU sub-assembly LH or combination meter assembly may be malfunctioning.
Initialization (When using the GTS):
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
w/ Adaptive High Beam System:
Enter the following menus: Body Electrical / AFS / Utility / Height Sensor Initialization.
| Tester Display |
|---|
| Height Sensor Initialization |
w/o Adaptive High Beam System:
Enter the following menus: Body Electrical / HL AutoLeveling / Utility / Height Sensor Initialization.
| Tester Display |
|---|
| Height Sensor Initialization |
Check the display on the GTS and press "Next".
Press "Exit".
Check the condition of the "Headlight System Uninitialized Visit Your Dealer" on the multi-information display.
| Condition | Specified Condition |
|---|---|
| The headlight ECU sub-assembly LH has been replaced with a new one. | Blinks 6 times at 2 Hz → Continuously blinks 3 times at 2 Hz. |
| Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed. | Off → Continuously blinks 3 times at 2 Hz. |
If initialization does not finish normally, restart the initialization procedure from step (i).
Check that initialization finishes normally and turn the ignition switch off.
The warning message will blink in the pattern indicating that initialization has completed successfully continuously until the ignition switch is turned off.
Initialization (When not using the GTS):
Turn the ignition switch off.
Turn the light control switch to the AUTO position.
Shine a light on the automatic light control sensor.
If troubleshooting is being performed in a bright area, such as outside on a sunny day, it will not be necessary to perform this step.
Perform the following steps within 5 seconds.
Turn the ignition switch to ON.
With the dimmer switch in high flash position, turn it from AUTO to TAIL to AUTO again 3 times or more.
Check that the parking lights turn from off to on and back off again.
Turn the light control switch to the AUTO position and move the dimmer switch in low position.
Perform the above operation within 5 seconds.
When initialization mode has been entered, "Headlight Leveling System Uninisialized" warning message on the multi-information display starts blinking at 1 Hz.
Check the condition of the "Headlight System Uninitialized Visit Your Dealer" on the multi-information display.
| Condition | Specified Condition |
|---|---|
| The headlight ECU sub-assembly LH has been replaced with a new one. | Blinks 6 times at 2 Hz → Continuously blinks 3 times at 2 Hz. |
| Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed. | Off → Continuously blinks 3 times at 2 Hz. |
If initialization does not finish normally, restart the initialization procedure from step (i).
Check that initialization finishes normally and turn the ignition switch off.
The warning message will blink in the pattern indicating that initialization has completed successfully continuously until the ignition switch is turned off.