Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › ADAPTIVE HIGH BEAM SYSTEM
RM37H0E _95 ADAS / AD _095317 ADVANCED DRIVER ASSISTANCE SYSTEM _0448417 ADAPTIVE HIGH BEAM SYSTEM D

ADVANCED DRIVER ASSISTANCE SYSTEM  ADAPTIVE HIGH BEAM SYSTEM  OPERATION CHECK  


ADAPTIVE HIGH BEAM SYSTEM OPERATION CHECK


NOTICE:

Make sure that the customize settings are set to default when performing the adaptive high beam system operation check.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>ADAPTIVE HIGH BEAM SYSTEM>CUSTOMIZE PARAMETERS


a.
E364130C01
0.125,0.104 0.438,0.26 0.313,0.156 10 false *a
*a Adaptive High Beam Indicator


When all of the following conditions are met, the adaptive high beam indicator illuminates (green) indicating the adaptive high beam system is on.

·

The ignition switch is ON.

·

The light control switch is in the head or AUTO position.

·

Turn the headlight dimmer switch to the low position.

·

Turn the adaptive high beam switch on.


NOTICE:
·

When the forward recognition camera cannot correctly detect objects in front of the vehicle due to inclement weather such as thick fog or other visual obstructions, the adaptive high beam system may not operate even if the adaptive high beam system indicator in the combination meter assembly is illuminated.

·

When the temperature of the forward recognition camera is excessively high, or forward recognition camera axis calibration is being performed due a change in the vehicle posture, such as when fully loaded, the adaptive high beam system may not operate even if the adaptive high beam indicator is illuminated.

·

When the cable is disconnected from the negative (-) auxiliary battery terminal, the adaptive high beam system may not operate until the vehicle steering sensor zero point calibration has been performed. After reconnecting the cable, drive the vehicle to initialize the steering sensor zero point value.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>INITIALIZATION




b.

When the following conditions are met while the adaptive high beam system is on, after a short period of time the high beam headlights will turn on.

·

Vehicle speed is more than approximately 15 km/h (9 mph).

·

There are no illuminated headlights or taillights of other vehicles in front of the vehicle.

·

The area in front of the vehicle has few street lights and is sufficiently dark.


i.

The high beam control mode changes in accordance with vehicle speed.

Illumination Mode Description Vehicle Speed
Except Europe Europe
Residential Area Mode At low speeds, in consideration of the drivers field of vision, the illuminated area is widened. The brightness of the headlights is adjusted to ensure that pedestrians are visible while not being dazzled. Reduces illumination of the side of the road. 15 to 30 km/h
(9 to 25 mph)
-
Normal Mode At medium speeds, the illuminated area in front of the vehicle is extended and necessary areas to the left and right of the vehicle are illuminated. 30 to 80 km/h
(25 to 50 mph)
60 to 100 km/h
(37 to 62 mph)
High Speed Mode At high speeds, the illuminated area in front of the vehicle is extended and increased in brightness and the additional high beams are used. 80 km/h or more
(50 mph or more)
100 km/h or more
(62 mph or more)



c.

When the following conditions are met while the adaptive high beam system is on, cut-off line tilt control (function that adjusts the upper illumination area of the low beam headlights) will operate.

·

Vehicle speed is more than approximately 30 km/h (19 mph).

·

The area in front of the vehicle is dark.

·

The headlights of oncoming vehicles or taillights of preceding vehicles are detected.

·

The area in front of the vehicle has few street lights and is sufficiently dark.



d.

When the following conditions are met while the adaptive high beam function is operating, after a short period of time the brightness and illumination area of the high beams will change according to the detected conditions.

·

Vehicle speed is more than approximately 15 km/h (9 mph).

·

The headlights of oncoming vehicles or taillights of preceding vehicles are detected.

·

The area in front of the vehicle has few street lights and is sufficiently dark.



e.

When the following conditions are met while the adaptive high beam function is operating, headlight swivel control will operate.

·

The vehicle speed is more than approximately 30 km/h (19 mph).

·

The environment is dark and there is no oncoming vehicle with its headlights illuminated and no preceding vehicle with its taillights illuminated.

·

The steering angle is a certain amount or more.



f.

When the following conditions are met while the adaptive high beam function is operating, the high beam headlights will turn off.

·

Vehicle speed is less than approximately 12 km/h (7 mph).

·

The headlights of oncoming vehicles or taillights of preceding vehicles are detected.

·

The area in front of the vehicle is light.

·

Multiple vehicles are detected in front of the vehicle.

·

The movement of a vehicle in front is rapid and causing glare.



g.

When the following conditions are met, operation of the adaptive high beam system is canceled and the adaptive high beam indicator in the combination meter assembly is turned off.

·

The ignition switch is turned off.

·

The light control switch is turned to any position except the AUTO or head position.

·

The low beams are not operating.

·

The dimmer switch is moved to the high position.

·

Turn the adaptive high beam switch off.