Home › Steering › STEERING COLUMN › STEERING SYSTEM
RM37H0E _55 Steering _095770 STEERING COLUMN _0449634 STEERING SYSTEM N

STEERING COLUMN  STEERING SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1. STEERING WHEEL OFF CENTER ADJUSTMENT PROCEDURE

a.

Inspect steering wheel off center.

i.

Turn the steering wheel assembly to the center position.


ii.
C447784C01
0.854,0.792 0.302,0.313 0.302,0.313 0.698,0.979 true 1.438,0.604 2.156,0.5 true 0.969,1.146 1.854,1.51 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.25,0.406 2.563,0.604 0.313,0.198 10 false *1 1.938,1.469 2.25,1.667 0.313,0.198 10 true *2
*1 Steering Wheel Assembly
*2 Upper Steering Column Cover
*a Masking Tape


Apply masking tape to the top center of the steering wheel assembly and upper steering column cover.


iii.

Drive the vehicle in a straight line for 100 m (328 ft.) at a constant speed of 56 km/h (35 mph), while holding the steering wheel assembly to maintain the course.


iv.
C447785C01
1.625,0.604 0.833,0.25 0.833,0.25 1.615,0.385 true 2.229,0.188 2.646,0.188 true 0.615,0.885 0.802,1.052 true 1.729,0.615 2.74,0.781 2.74,0.781 1.719,0.396 true 0.625,0.177 0.938,0.375 0.313,0.198 10 false *a 2.625,0.156 2.938,0.354 0.313,0.198 10 false *1 0.469,0.719 0.781,0.917 0.313,0.198 10 false *2 2.781,0.719 3.094,0.917 0.313,0.198 10 false *b
*1 Upper Steering Column Cover
*2 Steering Wheel Assembly
*a Masking Tape
*b Marked Line


Draw a line on the masking tape as shown in the illustration.


v.

Turn the steering wheel assembly to the center position.

HINT:

Look at the upper surface of the steering wheel assembly, steering spoke and SRS airbag line to find the center position.



vi.
C447786C01
0.615,0.885 0.781,1.021 true 2.198,0.198 2.604,0.198 true 1.74,0.594 2.698,0.813 true 1.552,0.365 0.865,0.26 0.865,0.26 1.427,0.625 true 0.458,0.75 0.729,0.927 0.271,0.177 10 false *1 2.656,0.125 2.969,0.323 0.313,0.198 10 false *1 2.74,0.74 3.052,0.938 0.313,0.198 10 false *b 0.667,0.125 0.979,0.323 0.313,0.198 10 false *a
*1 Upper Steering Column Cover
*2 Steering Wheel Assembly
*a Masking Tape
*b Marked Line


Draw a new line on the masking tape on the steering wheel assembly as shown in the illustration.


vii.

Measure the distance between the 2 lines on the masking tape on the steering wheel assembly.


viii.

Convert the measured distance to the steering angle.

HINT:
·

Measured distance of 1 mm (0.0394 in.) = Steering angle of approximately 1 degree

·

Make a note of the steering angle.





b.

Adjust the steering angle.

i.
C446707C01
0.823,1.24 0.938,1.708 0.938,1.708 1,1.25 true 0.875,1.729 1.188,1.885 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the tie rod assemblies LH and RH and steering rack end sub-assembly respectively.


ii.

Using a paper gauge, measure the thread length of the steering rack end sub-assemblies.

HINT:
·

Measure both RH and LH sides.

·

Make a note of the measured values.




iii.
C449428C01
2.667,1.917 2.833,1.917 2.833,1.917 2.833,2.167 true 2.385,1.865 2.698,2.063 0.313,0.198 10 false SST 1.604,2.76 1.917,2.958 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Remove the steering rack boot clips from the RH and LH No. 1 steering rack boots.


iv.

Loosen the RH and LH lock nuts.


v.

Turn the RH and LH steering rack end sub-assemblies by the same amount (but in different directions) according to the measured steering angle.

HINT:

One 360 degree turn of a steering rack end (1.5 mm (0.0591 in.) horizontal movement) equals 9 degrees of steering angle.



vi.

Using SST, tighten the RH and LH lock nuts to the specified torque.

SST
09612-24014  (09617-24011)

Torque:
Specified tightening torque : 88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Make sure that the difference in thread length between the RH and LH steering rack end sub-assemblies is within 1.5 mm (0.0591 in.).


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using SST (fulcrum length of 52 mm (2.0472 in.)) + torque wrench (fulcrum length of 380 mm (14.9606 in.)): 77.4 N*m (789 kgf*cm, 57 ft.*lbf)




vii.

Install the RH and LH steering rack boot clips.

HINT:
C447783C03
0.896,0.979 1.208,1.135 0.313,0.156 10 false *a 1.063,0.76 1.375,0.917 0.313,0.156 10 false *b 1.781,0.594 2.094,0.75 0.313,0.156 10 false *c 2.344,0.927 2.656,1.083 0.313,0.156 10 false *d
*a Clip Tab Positioning Area
*b 90°
*c 45°
*d 58°
V100135

Top of Vehicle
V100136

Rear of Vehicle


Make sure that the tabs of the clip are within the area shown in the illustration.