Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)
RM37H0E _55 Steering _095770 STEERING COLUMN _0449635 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) G

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  INSPECTION  


PROCEDURE

Hide 1.INSPECT TILT MOTOR

a.
C197978C86
2.396,1.083 2.802,1.365 0.406,0.281 2.042,1.115 2.354,0.667 true 1.354,1.115 1.042,0.667 true 0.302,0.229 0.51,0.417 0.208,0.188 10 false *a 2.385,0.573 2.729,0.76 0.344,0.188 10 false TIM+ 0.719,0.563 1.063,0.75 0.344,0.188 10 false TIM- 2.458,1.146 2.917,1.344 0.458,0.198 10 false D39
*a Component without harness connected
(Tilt Motor)


Apply 12 V battery voltage to the tilt motor connector. Then check the steering wheel tilt operation.

OK:
Tester Connection Specified Condition

Click Location & Routing(D39)Location & Routing

Click Connector(D39)Instrument Panel>Instrument Panel Wire>Steering Column Assembly

·

12 V battery positive (+) lead → Terminal D39-2 (TIM-)

·

12 V battery negative (-) lead → Terminal D39-1 (TIM+)


The steering wheel tilts down.
·

12 V battery positive (+) lead → Terminal D39-1 (TIM+)

·

12 V battery negative (-) lead → Terminal D39-2 (TIM-)


The steering wheel tilts up.



Hide 2.INSPECT TELESCOPIC MOTOR

a.
C376770C05
2.438,0.969 2.833,1.281 0.396,0.313 2.042,1.031 2.438,0.615 true 1.385,1.031 0.865,0.604 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 2.51,0.521 2.917,0.698 0.406,0.177 10 false TEM- 0.458,0.5 0.906,0.698 0.448,0.198 10 false TEM+ 2.5,1.042 2.958,1.24 0.458,0.198 10 false D25
*a Component without harness connected
(Telescopic Motor)


Apply 12 V battery voltage to the telescopic motor connector. Then check the steering column telescopic operation.

OK:
Tester Connection Specified Condition

Click Location & Routing(D25)Location & Routing

Click Connector(D25)Instrument Panel>Instrument Panel Wire>Steering Column Assembly

·

12 V battery positive (+) lead → Terminal D25-4 (TEM+)

·

12 V battery negative (-) lead → Terminal D25-1 (TEM-)


The steering column contracts.
·

12 V battery positive (+) lead → Terminal D25-1 (TEM-)

·

12 V battery negative (-) lead → Terminal D25-4 (TEM+)


The steering column extends.



Hide 45250 3.INSPECT STEERING COLUMN ASSEMBLY

a.
C449484N01
1.625,0.198 1.833,0.375 0.208,0.177 10 false A

Measure the length of the steering main shaft.

Standard length (A):
Specified Condition
423.7 to 483.7 mm
1.39 to 1.58 ft.



b.
C449485

Check that the 2 bushings are securely installed to the steering column assembly.

HINT:

If the bushings are deformed, missing or damaged, replace the steering column assembly with a new one.