Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) D

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  OPERATION CHECK  


CHECK CUSTOMIZE PARAMETERS


NOTICE:

The operation check below is based on the non-customized initial condition of the vehicle.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CHECK FOR INTERMITTENT PROBLEMS



CHECK PUSH-BUTTON START FUNCTION


a.

Check the push-button start function:

i.

Get into the vehicle while carrying the electrical key transmitter sub-assembly with the ignition switch off. With the shift state park (P), check that the key indicator display is displayed when the brake pedal is depressed. Check that the hybrid control system starts when the power switch is pressed after the key indicator display is displayed on the multi-information display.


ii.

While carrying the electrical key transmitter sub-assembly, check that the power source mode changes in the following order when the power switch is pressed with the brake pedal released: off → ACC → ON → off.


iii.

With the shift state park (P), check that the steering lock operates when a door is opened.


iv.
B581609C01
0.646,1.146 2.667,0.406 2.667,0.406 3,0.406 false 2.073,1.167 2.656,0.417 false 3.042,0.333 3.271,0.583 0.229,0.25 10 false *a
*a Inspection Point

The illustrations shown are examples only.


Check the push-button start function operation range for the front side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box, in the door pocket, in the console or on the floor.


HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PARTS LOCATION

·

Perform this inspection for both inspection points.




v.
B581610C01
0.688,0.375 2.677,1.417 2.677,1.417 3.01,1.417 false 2.042,0.396 2.667,1.417 false 3.052,1.344 3.281,1.594 0.229,0.25 10 false *a
*a Inspection Point

The illustrations shown are examples only.


Check the push-button start function operation range for the rear side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box, in the door pocket, in the console or on the floor.


HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PARTS LOCATION

·

Perform this inspection for both inspection points.






CHECK POWER SOURCE MODE CHANGING FUNCTION


a.

Check the ignition switch.

i.

Check that the power source mode changes according to the chart below.

Shift Position Brake Pedal Power Source Mode when Power Switch Pressed
Park (P) selected Released Off → ACC → ON → off
Park (P) selected Depressed Off → hybrid control system starts
Park (P) selected Depressed ACC → hybrid control system starts
Park (P) selected Depressed ON → hybrid control system starts
Park (P) selected Released / Depressed ON (READY) → off
Park (P) not selected Released / Depressed ACC → ON
Park (P) not selected Released / Depressed ON (READY) → off
Park (P) not selected Released / Depressed ON → off




CHECK TRANSMITTER BATTERY SAVING MODE FUNCTION


a.

Check the transmitter battery saving mode function:

i.

Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.


ii.

Check that the entry and start system does not operate while in transmitter battery saving mode.

HINT:

To cancel transmitter battery saving mode, press a switch of the electrical key transmitter sub-assembly.





CHECK ENTRY CANCEL FUNCTION


a.

Cancel the entry and start system and check that all the functions of the entry and start system no longer operate.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS

HINT:

While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless function, and the hybrid control system can be started by holding the electrical key transmitter sub-assembly near the power switch.