Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B427558E41
3.25,0.542 3.656,0.781 0.406,0.24 4.531,0.542 4.938,0.781 0.406,0.24 4.604,0.552 4.917,0.75 0.313,0.198 10 false D86 3.313,0.563 3.625,0.76 0.313,0.198 10 false G37

a.

Disconnect the D86 and G37 certification ECU (smart key ECU assembly) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item
G37-25 (STP1) - Body ground Input Stop light switch signal Brake pedal depressed → Brake pedal released 9 V or higher → 1 V or less Power Source Control

Stop Light Switch1


D86-4 (+B) - D86-18 (E) Input Power source Ignition switch off 11 to 14 V -
D86-15 (CUTB) - Body ground Input Dark current cut pin* Ignition switch off 11 to 14 V -
D86-18 (E) - Body ground - Ground Always Below 1 Ω -
D86-21 (SSW2) - Body ground Input SSW2 contact signal
HINT:

Backup for SSW1. Behaves the same way as SSW1.


Power switch pushed → power switch not pushed Below 15 Ω → 10 kΩ or higher Power Source Control

Start Switch2


D86-23 (SSW1) - Body ground Input SSW1 contact signal Power switch pushed → power switch not pushed Below 15 Ω → 10 kΩ or higher Power Source Control

Start Switch1


D86-19 (SPD) - Body ground Input Vehicle speed signal Always 30 kΩ or higher Power Source Control

Vehicle Speed Signal



*: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).



c.

Reconnect the D86 and G37 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item
G37-25 (STP1) - D86-18 (E) Input Stop light switch signal Brake pedal released → Brake pedal depressed 1 V or less → 9 V or higher Power Source Control

Stop Light Switch1


D86-14 (SLP) - D86-18 (E) Input Steering lock position signal Steering locked → Steering unlocked 11 to 14 V → 1.5 V or less Power Source Control

Steering Unlock Switch


D86-25 (SLR+) - D86-18 (E) Output Steering lock motor operation command signal
(Steering lock motor operation permission signal sent from the certification ECU (smart key ECU assembly))
When a door is opened, the steering lock motor will be operated if all of the following conditions are met:
·

The steering is unlocked.

·

The ignition switch is off.

·

The shift state park (P).


Pulse generation
(See waveform 1)
-
D86-13 (LIN) - D86-18 (E) Input/Output LIN communication line Ignition switch ON Pulse generation Entry&Start

Steering Lock Start Cond


D86-3 (IGB) - D86-18 (E) Output IGB signal Ignition switch off → Ignition switch ON 1 V or less → 8.5 V or higher -
D86-22 (P) - D86-18 (E) Input P position signal Procedure:
1.

Ignition switch ON

2.

Shift state park (P)


Pulse generation
(See waveform 7)
Power Source Control

Shift P Signal


D86-21 (SSW2) - D86-18 (E) Input SSW2 contact signal
HINT:

Backup for SSW1. Behaves the same way as SSW1.


Power switch not pushed → power switch pushed 9 V or higher → 1 V or less Power Source Control

Start Switch2


D86-23 (SSW1) - D86-18 (E) Input SSW1 contact signal Power switch not pushed → power switch pushed 9 V or higher → 1 V or less Power Source Control

Start Switch1


D86-16 (ACCD) - D86-18 (E) Output ACC signal Ignition switch off → Ignition switch ACC 1 V or less → 8.5 V or higher Power Source Control

ACC Relay Monitor


D86-17 (IG1D) - D86-18 (E) Output IG1 signal Ignition switch ACC → Ignition switch ON 1 V or less → 9 V or higher Power Source Control

IG Relay Monitor (Outside)


D86-19 (SPD) - D86-18 (E) Input Vehicle speed signal Vehicle being driven at approximately 5 km/h (3 mph) Pulse generation
(See waveform 2)
Power Source Control

Vehicle Speed Signal


D86-27 (ST2) - D86-18 (E) Output Starter request signal With the brake pedal depressed, the power switch is pressed and held → After approximately 3 sec. has elapsed, the power switch is released 8.5 V or higher → 1 V or less -
D86-8 (CLG5) - D86-18 (E) Output Output to No. 1 indoor electrical key antenna assembly (front floor) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
D86-9 (CG5B) - D86-18 (E) Output Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
G37-5 (CLG6) - D86-18 (E) Output Output to No. 1 indoor electrical key antenna assembly (rear floor) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
G37-6 (CG6B) - D86-18 (E) Output Output to No. 1 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG6 output terminal) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
D86-5 (TXCT) - D86-11 (AGND) Output Signal output to transponder key amplifier Ignition switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V Entry&Start
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


D86-6 (CODE) - D86-11 (AGND) Input Signal input from transponder key amplifier Ignition switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
D86-7 (VC5) - D86-11 (AGND) Output Transponder key amplifier power supply Ignition switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
D86-11 (AGND) - Body ground - Transponder key amplifier ground Always Below 1 Ω
D86-5 (TXCT) - D86-11 (AGND) Output Signal output to transponder key amplifier
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)
Ignition switch off, key not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 4)
Entry&Start
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above


D86-6 (CODE) - D86-11 (AGND) Input Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Ignition switch off, power switch pressed with key held near power switch* Pulse generation
(See waveform 5)
D86-7 (VC5) - D86-11 (AGND) Output Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)
Ignition switch off, key not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 6)
D86-20 (IND) - D86-18 (E) Output Security indicator output Ignition switch off → ignition switch ON Pulse generation → Below 2 V -

HINT:
·

The waveform of the steering lock actuator motor stopped can be checked without performing any particular operation.

·

The waveform of the steering lock actuator motor operating can be checked if either of the following operations is performed:

-

To unlock the steering, bring the electrical key transmitter sub-assembly into the cabin and turn the ignition switch to ACC or to ON.

-

To lock the steering, open a door with the ignition switch off and the shift state park (P).


·

*: Remove the transmitter battery before performing this inspection.




e.

Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C221561C22
0.229,0.406 1.635,0.573 1.406,0.167 1.469,1.573 2.438,1.698 0.969,0.125 2.281,0.469 2.708,0.625 0.427,0.156 1.938,1.698 2.021,1.979 2.021,1.979 2.073,1.979 false 1.646,0.438 2.76,0.198 2.76,0.198 2.833,0.198 false 2.75,0.208 2.552,0.458 false 2.906,1.583 3.281,1.729 0.375,0.146 10 GND 2.125,1.896 2.615,2.042 0.49,0.146 10 *b 2.865,0.125 3.229,0.354 0.365,0.229 10 *a
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1

Item Content
Tester Connection D86-25 (SLR+) - D86-18(E)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition When a door is opened, the steering lock motor will be operated if all of the following conditions are met:
·

The steering is unlocked.

·

The ignition switch is off.

·

The shift state park (P).




ii.
B220145N12
2.875,1.164 3.228,1.332 0.353,0.168 10 GND

Waveform 2

Item Content
Tester Connection D86-19 (SPD) - D86-18(E)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Vehicle being driven at approximately 5 km/h (3 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



iii.
B340874C02
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND 1.01,1.917 1.469,2.115 0.458,0.198 10 false *a 2.135,1.938 2.594,2.135 0.458,0.198 10 false *b
*a For 30 seconds after any door closed
*b After 30 seconds or more have elapsed since any door closed


Waveform 3

Item Content
Tester Connection D86-8 (CLG5) - D86-18 (E)
D86-9 (CG5B) - D86-18 (E)
G37-5 (CLG6) - D86-18 (E)
G37-6 (CG6B) - D86-18 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door




iv.
B051052N19
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 4

Item Content
Tester Connection D86-5 (TXCT) - D86-11 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch off, key not in cabin, within 30 seconds after power switch pressed


v.
B368716C01
0.104,0.135 0.417,0.292 0.313,0.156 10 false *a 0.094,1.896 0.406,2.052 0.313,0.156 10 false *b 3.031,1.219 3.427,1.49 0.396,0.271 10 false GND 3.031,2.948 3.427,3.219 0.396,0.271 10 false GND
*a Waveform
*b Waveform (detail)


Waveform 5

Item Content
Tester Connection D86-6 (CODE) - D86-11 (AGND)
Tool Setting
·

Waveform:

2 V/DIV., 20 ms./DIV.

·

Waveform (detail):

2 V/DIV., 100 μs./DIV.


Condition Ignition switch off, power switch pressed with key held near power switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



vi.
B216007N06
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 6

Item Content
Tester Connection D86-7 (VC5) - D86-11 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Ignition switch off, key not in cabin, within 30 seconds after power switch pressed


vii.
C372252E03
3.073,1.219 3.427,1.406 0.354,0.188 10 false GND

Waveform 7

Item Content
Tester Connection D86-22 (P) - D86-18 (E)
Tool Setting 10 V/DIV., 10 ms./DIV.
Condition Procedure:
1.

Ignition switch ON

2.

Shift state park (P)



HINT:

The waveform will vary depending on the shift state.





CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)


C195844E26
1.927,0.646 2.323,0.885 0.396,0.24 2.01,0.667 2.448,0.927 0.438,0.26 10 false D24

a.

Disconnect the D24 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item
D24-1 (GND) - Body ground - Ground Always Below 1 Ω -
D24-6 (IG2) - D24-1 (GND) Input Power source mode signal Ignition switch off → Ignition switch ON Below 1 V → 11 to 14 V -
D24-7 (B) - Body ground Input Power source Ignition switch off 11 to 14 V -


c.

Reconnect the D24 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


d.

Measure the voltage and puless according to the value(s) in the table below.

Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item
D24-4 (SLP1) - D24-1 (GND) Output Steering lock bar position signal (output signal from steering unlock sensor) Steering locked → unlocked 11 to 14 V → Below 1.5 V Entry&Start
·

Sensor Value


D24-5 (LIN) - D24-1 (GND) Input/Output LIN communication line Ignition switch ON Pulse generation Entry&Start
·

Steering Lock Start Cond




e.

Check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition Related Data List Item
D24-3 (IGE) - D24-1 (GND) Input Steering lock motor activation command signal Any door opened when conditions below met, and then steering lock motor activated:
·

Shift state park (P)

·

Steering lock unlocked in advance by carrying key and turning ignition switch to ON

·

After above conditions met, ignition switch turned off


Pulse generation
(see waveform 1)
Entry&Start
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive



HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the ignition switch to ACC or to ON.

-

To lock the steering, turn the ignition switch off with the shift state park (P), and then open a door.





f.

Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C221561C19
0.292,0.396 1.698,0.563 1.406,0.167 1.521,1.583 2.49,1.708 0.969,0.125 2.292,0.448 2.719,0.604 0.427,0.156 2.083,1.708 2.167,1.99 2.167,1.99 2.219,1.99 false 1.698,0.438 2.813,0.198 2.813,0.198 2.885,0.198 false 2.802,0.198 2.604,0.448 false 2.917,1.583 3.385,1.958 0.469,0.375 10 GND 2.271,1.906 2.76,2.052 0.49,0.146 10 *b 2.948,0.104 3.313,0.333 0.365,0.229 10 *a
*a Steering Lock Motor not Operating
*b Steering Lock Motor Operating


Waveform 1

Item Content
Tester Connection D24-3 (IGE) - D24-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Any door opened when conditions below met, and then steering lock motor activated:
·

Shift state park (P)

·

Steering lock unlocked in advance by carrying key and turning ignition switch to ON

·

After above conditions met, ignition switch turned off






CHECK ID CODE BOX (IMMOBILISER CODE ECU)


B278917E45
3.396,0.156 3.792,0.385 0.396,0.229 3.479,0.177 3.802,0.354 0.323,0.177 10 false D73

a.

Disconnect the D73 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item
D73-1 (+B) - Body ground Input Power source Ignition switch off 11 to 14 V -
D73-5 (GND) - Body ground - Ground Always Below 1 Ω


c.

Reconnect the D73 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item
D73-3 (EFII) - D73-5 (GND) Input EFI communication input
(Signal input from EV control ECU to ID code box (immobiliser code ECU))
Ignition switch off 11 to 14 V Entry&Start
·

EFI/EV Code Receive

·

Engine/System Start Request


D73-3 (EFII) - D73-5 (GND) Input EFI communication input
(Signal input from EV control ECU to ID code box (immobiliser code ECU))
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
D73-4 (EFIO) - D73-5 (GND) Output EFI communication output
(Signal output from ID code box (immobiliser code ECU) to EV control ECU)
Ignition switch off Below 1 V
D73-4 (EFIO) - D73-5 (GND) Output EFI communication output
(Signal output from ID code box (immobiliser code ECU) to EV control ECU)
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 2)
D73-2 (LIN1) - D73-5 (GND) Input/Output LIN communication line Ignition switch ON Pulse generation Entry&Start
·

Steering Lock Start Cond




e.

Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Item Content
Tester Connection D73-3 (EFII) - D73-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery


ii.

Waveform 2

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Item Content
Tester Connection D73-4 (EFIO) - D73-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery




CHECK EV CONTROL ECU


A352214C17
0.646,0.052 1.115,0.406 0.469,0.354 1.958,0.271 2.427,0.625 0.469,0.354 3.365,0.271 3.833,0.625 0.469,0.354 4.729,0.271 5.198,0.625 0.469,0.354 6.021,0.469 6.49,0.823 0.469,0.354 0.646,0.479 1.115,0.833 0.469,0.354 6.021,0.052 6.49,0.406 0.469,0.354 0.76,0.135 1.219,0.333 0.458,0.198 10 false G14 2.083,0.375 2.542,0.573 0.458,0.198 10 false A15 3.49,0.385 3.948,0.583 0.458,0.198 10 false A16 4.833,0.385 5.292,0.583 0.458,0.198 10 false A17 6.177,0.146 6.635,0.344 0.458,0.198 10 false A8 0.771,0.583 1.229,0.781 0.458,0.198 10 false A14 1.156,0.063 1.469,0.26 0.313,0.198 10 false *A 1.156,0.51 1.469,0.708 0.313,0.198 10 false *B 6.156,0.573 6.615,0.771 0.458,0.198 10 false D15 6.542,0.073 6.854,0.271 0.313,0.198 10 false *A 6.552,0.5 6.865,0.698 0.313,0.198 10 false *B
*A for LHD *B for RHD


a.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Terminal Description Condition Specified Condition Related Data List Item

*1: for RHD

*2: for LHD

A16-7 (IG2) - A17-4 (E1) Input Power source Ignition switch ON 11 to 14 V -
A17-4 (E1) - Body ground - Ground Always Below 1 Ω -
D15-29 (IMO) - A17-4 (E1)*1 Output EFI communication output
(Signal output from EV control ECU to ID code box (immobiliser code ECU))
Ignition switch off 11 to 14 V Entry&Start
·

EFI/EV Code Receive

·

Engine/System Start Request


D15-29 (IMO) - A17-4 (E1)*1 Output EFI communication output
(Signal output from EV control ECU to ID code box (immobiliser code ECU))
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
A8-29 (IMO) - A17-4 (E1)*2 Output EFI communication output
(Signal output from EV control ECU to ID code box (immobiliser code ECU))
Ignition switch off 11 to 14 V
A8-29 (IMO) - A17-4 (E1)*2 Output EFI communication output
(Signal output from EV control ECU to ID code box (immobiliser code ECU))
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
D15-26 (IMI) - A17-4 (E1)*1 Input EFI communication input
(Signal input from ID code box (immobiliser code ECU) to EV control ECU)
Ignition switch off Below 1 V
D15-26 (IMI) - A17-4 (E1)*1 Input EFI communication input
(Signal input from ID code box (immobiliser code ECU) to EV control ECU)
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 2)
A8-26 (IMI) - A17-4 (E1)*2 Input EFI communication input
(Signal input from ID code box (immobiliser code ECU) to EV control ECU)
Ignition switch off Below 1 V
A8-26 (IMI) - A17-4 (E1)*2 Input EFI communication input
(Signal input from ID code box (immobiliser code ECU) to EV control ECU)
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 2)


b.

Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Item Content

*1: for RHD

*2: for LHD

Tester Connection D15-29 (IMO) - A17-4 (E1)*1
A8-29 (IMO) - A17-4 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery


ii.

Waveform 2

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Item Content

*1: for RHD

*2: for LHD

Tester Connection D15-26 (IMI) - A17-4 (E1)*1
A8-26 (IMI) - A17-4 (E1)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery




CHECK POWER SWITCH


B271001E54
3.354,0.229 3.729,0.458 0.375,0.229 3.427,0.25 3.74,0.427 0.313,0.177 10 false D98

a.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
D98-6 (AGND) - Body ground - - Transponder key amplifier ground Always Below 1 Ω -
D98-7 (TXCT) - D98-6 (AGND) - Input Immobiliser communication input Ignition switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -
D98-8 (CODE) - D98-6 (AGND) - Output Immobiliser communication output Ignition switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -
D98-10 (VC5) - D98-6 (AGND) - Input Transponder key amplifier power supply Ignition switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -


b.

Check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
D98-7 (TXCT) - D98-6 (AGND) - Input Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)
Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 1)
Entry&Start
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above


D98-8 (CODE) - D98-6 (AGND) - Output Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Ignition switch off, ignition switch pressed with electrical key transmitter sub-assembly held near power switch* Pulse generation
(See waveform 2)
D98-10 (VC5) - D98-6 (AGND) - Input Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)
Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed Pulse generation
(See waveform 3)

HINT:

*: Remove the transmitter battery before performing this inspection.



c.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N18
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1

Item Content
Tester Connection D98-7 (TXCT) - D98-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed


ii.
B368716C01
0.104,0.135 0.417,0.292 0.313,0.156 10 false *a 0.094,1.896 0.406,2.052 0.313,0.156 10 false *b 3.031,1.219 3.427,1.49 0.396,0.271 10 false GND 3.031,2.948 3.427,3.219 0.396,0.271 10 false GND
*a Waveform
*b Waveform (detail)


Waveform 2

Item Content
Tester Connection D98-8 (CODE) - D98-6 (AGND)
Tool Setting Procedure:
·

Waveform

2 V/DIV., 20 ms./DIV.

·

Waveform (detail)

2 V/DIV., 100 μs./DIV.


Condition Ignition switch off, ignition switch pressed with electrical key transmitter sub-assembly held near power switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



iii.
B216007N05
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3

Item Content
Tester Connection D98-10 (VC5) - D98-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed