The steering lock ECU (steering lock actuator or upper bracket assembly) communicates with the GTS through the certification ECU (smart key ECU assembly) which uses CAN communication. If the CAN communication system or certification ECU (smart key ECU assembly) is malfunctioning, Data List items may not be normal.
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
DATA LIST
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock ECU (steering lock actuator or upper bracket assembly) | OFF or ON | OFF: Steering locked
ON: Steering unlocked |
·
When the shift state park (P) and the ignition switch is off, if any door is opened, the steering is locked. ·
When the electrical key transmitter sub-assembly is in the cabin and the ignition switch is turned to ACC or to ON, the steering unlocks. ·
The hybrid control system cannot be started when the steering unlock signal is off. |
| Stop Light Switch1 | State of brake pedal | OFF or ON | OFF: Brake pedal released
ON: Brake pedal depressed |
·
Use this item to determine if the stop light switch assembly is malfunctioning. ·
The hybrid control system cannot be started when this item is OFF. ·
If the stop light switch assembly is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time. |
| Start Switch1 | Power switch 1 status | OFF or ON | OFF: Power switch not pressed
ON: Power switch pressed |
·
If the power switch is pressed for a short time, the display may not change. ·
Use this item to determine if the power switch input signal is malfunctioning. |
| Start Switch2 | Power switch 2 status | OFF or ON | OFF: Power switch not pressed
ON: Power switch pressed |
·
Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal. ·
Behaves the same way as power switch 1. |
| Latch Circuit | Status of IG related backup circuits | OFF or ON | OFF: Ignition switch off
ON: Ignition switch ON |
·
Operates in almost the same manner as the IG relay. ·
When the ignition switch is ACC, OFF is displayed. |
| Starter Request Signal | Hybrid control system start request signal status | OFF or ON | OFF: The power switch is not pressed
ON: With the shift state park (P) and the brake pedal depressed, the power switch is pressed and held |
·
When the hybrid control system cannot be started due to a start request signal malfunction, OFF is displayed. ·
When the power switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the power switch needs to be pressed and held for a certain period of time. |
| ACC Relay Monitor | ACC relay activation | OFF or ON | OFF: Ignition switch off
ON: Ignition switch ACC |
When the ignition switch is ON, ON is displayed. |
| Vehicle Speed Signal | Vehicle being driven or stopped | Stop or Run | Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more |
- |
| Shift P Signal Pulse | P position signal status | Normal2, Normal3, Normal4, Normal5 or Unknown | Normal2: Signal normal and park (P) selected
Normal3: Signal normal and shift state other than (P) Normal4: Signal normal and park (N) selected Normal5: Signal normal and park other than (P) or (N) selected Unknown: - |
Use this item to determine if the P position signal is malfunctioning. |
| Power Supply Condition | Power supply state | All OFF, ACC ON, IG ON or ST ON | All OFF: Ignition switch off (ACC and IG)
ACC ON: Ignition switch ACC IG ON: Ignition switch ON ST ON: Sending hybrid control system start request signal |
- |
| Powertrain Type | Vehicle identification | HV-AT, Cnv-MT, Cnv-AT, Cnv-MMT, S&S-MT, S&S-AT, S&S-MMT or PHV-AT | Cnv-AT: Conventional A/T model (w/o Hybrid System) | - |
| Park Signal Mismatch | P position signal malfunction | No or Yes | No: Signal normal
Yes: Signal malfunction (signals via CAN communication and direct line do not match) |
Even when Yes is displayed, it is still possible to turn the ignition switch off (the power source mode will not be stuck in ACC or ON). |
| Str Lock/Unlock Wait T-Out | Steering lock or unlock malfunction | No or Yes | No: Lock and unlock normal
Yes: Lock or unlock malfunction (e.g. steering lock is stuck etc.) |
When the hybrid control system cannot be started due to a steering lock or unlock malfunction, Yes is displayed. |
| Key Certif Wait T-Out | Key verification malfunction | No or Yes | No: Verification normal
Yes: Verification error (Detected due to the electrical key transmitter sub-assembly ID code and the ID code stored in the certification ECU (smart key ECU assembly) not matching) |
When the hybrid control system cannot be started due to a key verification error, Yes is displayed. |
| IG Circuit | IG relay coil circuit malfunction | OK or NG | OK: Circuit normal
NG: Circuit malfunctioning |
·
Use this item to determine if the IG relay is malfunctioning. ·
When the hybrid control system cannot be started due to an IG relay malfunction, NG is displayed. |
| IG Relay Monitor (Outside) | IG relay coil voltage monitor status | OFF or ON | OFF: Ignition switch off
ON: Ignition switch ON |
·
Use this item to determine if the IG relay is malfunctioning. ·
When the ignition switch is ACC, OFF is displayed. |
| IG Relay Monitor (Inside) | IG relay activation | OFF or ON | OFF: Ignition switch off
ON: Ignition switch ON |
·
Use this item to determine if the IG relay is malfunctioning. ·
When the ignition switch is ACC, OFF is displayed. |
| Number of Diagnosis Code | Number of DTCs | 0 to 255 | 0 | - |
*1: Press the power switch with the brake pedal released and check that the ignition switch turns to ACC.
*2: Press the power switch with the brake pedal released and check that the ignition switch turns to ON.
*3: Depress the brake pedal (stop light switch assembly is on).
*4: Press the power switch with the brake pedal depressed and check that the hybrid control system starts.
*5: Press the power switch with the brake pedal depressed and check that the ignition switch turns off.
*6: Release the brake pedal.
*7: Open a door.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Unmatched Vehicle-ID | Key No. (incorrect or correct) | Yes or No | Yes: Communication malfunction
No: Communication normal |
The vehicle ID registered in the vehicle and the vehicle ID registered in the electrical key transmitter sub-assembly are different (if a key from another vehicle is brought into the vehicle exterior detection area while the doors are locked, "Yes" is displayed for "Unmatched Vehicle-ID" in the Data List).
Other potential causes: ·
An electrical key transmitter sub-assembly from a different vehicle is being used. ·
A communication error due to wave interference. ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning. |
| No Response | Communication response | Yes or No | Yes: Communication malfunction
No: Communication normal |
The vehicle IDs registered in the vehicle and electrical key transmitter sub-assembly match, but there is no response from the electrical key transmitter sub-assembly. (If the electrical key transmitter sub-assembly is not in the detection area or the transmitter battery is depleted resulting in a matching code not being detected when a lock switch or the power switch is pressed, etc., "Yes" is displayed for "No Response" in the Data List. If there is wave interference in the LF band that the vehicle uses for transmission or the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "No Response" in the Data List.)
Other potential causes: ·
An electrical key transmitter sub-assembly from a different vehicle is being used. ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning. |
| Key Low Battery | Transmitter battery depleted | No or Yes | No: Transmitter battery not depleted
Yes: Transmitter battery depleted |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.
|
| # Codes | Number of DTCs | 0 to 255 | 0 | - |
| Immobilizer when IG=ON | Immobiliser function status when ignition switch ON | SET or UNSET | SET: Immobiliser function set (driver door opened and closed with ignition switch ON)
UNSET: Immobiliser function not set with ignition switch ON or immobiliser function unset 40 times after immobiliser function set |
- |
| Immobiliser | Immobiliser function status determined by certification ECU (smart key ECU assembly)*9 | Set or Unset | Set: Immobiliser set (hybrid control system start prohibited) (ignition switch off)
Unset: Immobiliser unset (hybrid control system start permitted) (ignition switch ACC or ON) |
The hybrid control system cannot be started when Set is displayed.
|
| Master Key | Matching of master key ID code and ID code registered in certification ECU (smart key ECU assembly) | Match or No Match | Match: ID code of master key matches ID code registered in certification ECU (smart key ECU assembly)
No Match: ID code of master key does not match ID code registered in certification ECU (smart key ECU assembly) |
- |
| Sub Key | Matching of sub key ID code and ID code registered in certification ECU (smart key ECU assembly) | Match or No Match | Match: ID code of sub key matches ID code registered in certification ECU (smart key ECU assembly)
No Match: ID code of sub key does not match ID code registered in certification ECU (smart key ECU assembly) |
- |
| BCC Malfunction | BCC signal status of transponder chip*1 | OK or NG | OK: BCC signal normal
NG: BCC signal malfunction (malfunction in code computation in electrical key transmitter sub-assembly/certification ECU (smart key ECU assembly)) |
Problems may be caused by the following:
·
Communication errors due to wave interference (LF). ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) malfunctioning. |
| Abnormal Status | Transponder chip status signal*1 | OK or NG | OK: Transponder chip status signal normal
NG: Transponder chip status signal malfunction (malfunction in code computation in electrical key transmitter sub-assembly/certification ECU (smart key ECU assembly)) |
Problems may be caused by the following:
·
Communication errors due to wave interference (LF). ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) malfunctioning. |
| Different Encrypt Code | Matching of transponder chip code and certification ECU (smart key ECU assembly) code*1 | OK or NG | OK: Codes of transponder chip and certification ECU (smart key ECU assembly) match
NG: Codes of transponder chip and certification ECU (smart key ECU assembly) do not match |
Problems may be caused by the following:
·
An electrical key transmitter sub-assembly from a different vehicle is being used. ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) malfunctioning. |
| Different Serial Number | Vehicle serial number*1 | OK or NG | OK: Signal from transponder chip and vehicle serial number stored in the certification ECU (smart key ECU assembly) match
NG: Signal from transponder chip and vehicle serial number stored in the certification ECU (smart key ECU assembly) do not match |
Problems may be caused by the following:
·
An electrical key transmitter sub-assembly from a different vehicle is being used. ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) malfunctioning. |
| Frame Error | State of data sent from electrical key transmitter sub-assembly | OK or NG | OK: No problem with data sent from electrical key transmitter sub-assembly
NG: Problem with data sent from electrical key transmitter sub-assembly |
Problems may be caused by the following:
·
Communication errors due to wave interference. ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) malfunctioning. |
| Response | Electrical key transmitter sub-assembly response to signal from certification ECU (smart key ECU assembly) | OK or NG | OK: Electrical key transmitter sub-assembly responds to signal from certification ECU (smart key ECU assembly)
NG: Electrical key transmitter sub-assembly does not respond to signal from certification ECU (smart key ECU assembly) |
Problems may be caused by the following:
·
An electrical key transmitter sub-assembly from a different vehicle is being used. ·
The electrical key transmitter sub-assembly, certification ECU (smart key ECU assembly) or power switch malfunctioning. |
| Wireless Starter Com ID | Certification between remote engine start ECU and certification ECU (smart key ECU assembly) | No Regd or Regd | No Regd: Certification between remote engine start ECU and certification ECU (smart key ECU assembly) not complete
Regd: Certification between remote engine start ECU and certification ECU (smart key ECU assembly) complete |
- |
| Wireless C Code | Registration status between remote engine start ECU and certification ECU (smart key ECU assembly) | No Regd or Regd | No Regd: ID not registered between remote engine start ECU and certification ECU (smart key ECU assembly)
Regd: ID registered between remote engine start ECU and certification ECU (smart key ECU assembly) |
Problems may be caused by the following:
·
DTC B2779 is stored. ·
Remote engine start ECU registration has not been performed. ·
Malfunctions in the certification ECU (smart key ECU assembly) or remote engine start ECU. |
| Steering Lock Sleep Cond | Steering lock ECU sleep availability | No or Yes | No: Sleep not available
Yes: Sleep available |
- |
| Steering Lock Start Cond | Steering lock ECU wake up signal status | No or Yes | No: Wake up signal not sent
Yes: Wake up signal sent |
- |
| Engine/System Start Condition | Hybrid control system start permission from steering lock ECU (steering lock actuator or upper bracket assembly)*2 | NG or OK | NG: Hybrid control system start prohibited
OK: Hybrid control system start permitted |
·
When OK is displayed, the certification ECU (smart key ECU assembly) receives an unlock confirmation signal from the steering lock ECU (steering lock actuator or upper bracket assembly) and makes hybrid control system starting possible. ·
The hybrid control system cannot be started when NG is displayed. |
| Sensor Value | History of malfunction of position sensor in steering lock ECU (steering lock actuator or upper bracket assembly) (DTC B2781 is stored) | OK or NG(Past) | OK: History of malfunction for the lock or unlock sensor in the steering lock ECU (steering lock actuator or upper bracket assembly) does not exist.
NG(Past): History of both the lock and unlock sensors in the steering lock ECU (steering lock actuator or upper bracket assembly) being on exists. (Under normal operation, neither sensor is on.) |
When NG(Past) is displayed, either the position sensor in the steering lock ECU (steering lock actuator or upper bracket assembly) or the assembly itself may be malfunctioning. |
| Power Supply Short | History of signal error (short) sent from certification ECU (smart key ECU assembly) to steering lock ECU (steering lock actuator or upper bracket assembly) (DTC B2782 is stored) | OK or NG(Past) | OK: History of motor power source short does not exist
NG(Past): History of motor power source short exists |
This item displays history of a malfunction in the circuit between the certification ECU (smart key ECU assembly) and the steering lock ECU (steering lock actuator or upper bracket assembly). |
| Motor Driver Short | History of malfunction (short) in steering lock ECU (steering lock actuator or upper bracket assembly) motor circuit (DTC B2781 is stored) | OK or NG(Past) | OK: History of short in the motor circuit does not exist
NG(Past): History of short in the motor circuit exists |
This item displays history of a malfunction in the steering lock motor circuit in the steering lock ECU (steering lock actuator or upper bracket assembly). |
| Lock/Unlock Receive | History of receiving an unlock request signal | No or Yes | No: History of receiving an unlock request signal does not exist
Yes: History of receiving an unlock request signal exists |
- |
| Lock Bar Stuck Error | History of steering not being able to unlock properly when steering lock operates for a certain period of time | OK or NG(Past) | OK: History of steering lock being stuck does not exist
NG(Past): History of steering lock being stuck exists |
- |
| ID-BOX Sleep Condition | ID code box (immobiliser code ECU) sleep mode status*9 | Yes or No | Yes: ID code box (immobiliser code ECU) sleep mode possible
No: ID code box (immobiliser code ECU) sleep mode not possible |
- |
| ID-BOX Start Condition | ID code box (immobiliser code ECU) status*3 | Yes or No | Yes: Wake-up signal sent by ID code box (immobiliser code ECU)
No: Wake-up signal not sent by ID code box (immobiliser code ECU) |
- |
| Engine/System Start Request | Request to certification ECU (smart key ECU assembly) to permit EV control ECU to start hybrid control system*9 | OK or NG | OK: Signal received
NG: Signal not received |
·
The ID code box (immobiliser code ECU) receives the immobiliser unset (hybrid control system start permitted) signal from the certification ECU (smart key ECU assembly) and permits fuel injection and ignition when OK is displayed. ·
The hybrid control system cannot be started when NG is displayed. |
| 3bit Code Request | 3-bit code request condition | OK or NG | OK: 3-bit code request condition signal received
NG: 3-bit code request condition signal not received |
- |
| S Code Check | S code verification result*5 | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed:
·
The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the hybrid control system cannot be started). |
| L Code Check | L code verification result*6 | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed:
·
The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the hybrid control system cannot be started). |
| Unlock Request Receive | Status of steering unlock command from certification ECU (smart key ECU assembly)*7,*9 | OK or NG | OK: Unlock request signal received within 10 seconds of ignition switch being turned to ON or to ACC or of a hybrid control system start operation being performed
NG: Ignition switch not turned to ON or to ACC and hybrid control system start operation not being performed |
·
The hybrid control system cannot be started when an unlock request signal cannot be received. ·
If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Lock Request Receive | Status of steering lock command from certification ECU (smart key ECU assembly)*8,*9 | OK or NG | OK: Lock request signal received within 10 seconds of any of the doors being opened with shift state park (P) and ignition switch off.
NG: Except above |
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| S Code Check(Past) | Verification result history between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) | OK or NG(Past) | OK: History of abnormal verification result does not exist
NG(Past): History of abnormal verification result exists |
- |
| L Code Check(Past) | Verification result history between the ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) | OK or NG(Past) | OK: History of abnormal verification result does not exist
NG(Past): History of abnormal verification result exists |
- |
| Steering Lock | Steering lock ECU (steering lock actuator or upper bracket assembly) lock confirmation status | Unset or Set | Unset: Lock not confirmed
Set: Lock confirmed |
When Unset is displayed, the steering is not locked. |
| Steering Unlock | Steering lock ECU (steering lock actuator or upper bracket assembly) unlock confirmation status | Unset or Set | Unset: Unlock not confirmed
Set: Unlock confirmed |
When Unset is displayed, the steering is not unlocked (the hybrid control system cannot be started). |
| EFI/EV Code Receive | Certification information sent to ID code box (immobiliser code ECU) from EV control ECU when EV control ECU receives hybrid control system start permission signal from ID code box (immobiliser code ECU)*4,*9 | OK or NG | OK: Signal from EV control ECU to unset immobiliser received by ID code box (immobiliser code ECU)
NG: Signal from EV control ECU to unset immobiliser not received by ID code box (immobiliser code ECU) |
- |
| EFI/EV ECU Communication | State of communication to unset immobiliser between certification ECU (smart key ECU assembly) and EV control ECU | OK or NG | OK: Communication to unset immobiliser has started between certification ECU (smart key ECU assembly) and EV control ECU
NG: Communication to unset immobiliser has not started between certification ECU (smart key ECU assembly) and EV control ECU |
If this item displays "NG" even though the conditions to unset the immobiliser have been met and the value of Data List item "Engine/System Start Request" is "OK", the EV control ECU may be malfunctioning. When the hybrid control system cannot be started, use this Data List item during troubleshooting. |
| R Code Check | Verification result between the DCM (telephone transceiver assembly) and ID code box (immobiliser code ECU) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
Not applicable |
| B Code Difference | B code mismatch | Yes or No | Yes: Communication malfunction
No: Communication normal |
- |
| B Code | B code registration status | Regd or No Regd | Regd: B code registered correctly
No Regd: B code not registered correctly |
- |
| Vehicle ID (Key Registration) | Status of vehicle ID (key registration) | OK or NG | OK: Vehicle ID normal (key registration)
NG: Vehicle ID malfunction (key registration) |
- |
| Key Registration Status | Status of key registration | OK or NG | OK: Key registration normal
NG: Key registration malfunction |
- |
| S/L Code Registration Status | Status of S/L code registration | OK or NG | OK: S/L code registration normal
NG: S/L code registration malfunction |
- |
| Ignition Available Area | Ignition available area | Front or All | Customize setting displayed | - |
| Key Low Battery Warning | Low transmitter battery warning | OFF or ON | Customize setting displayed | - |
| Key Left in Vehicle Buz | Key left in vehicle buzzer | OFF or ON | Customize setting displayed | - |
| Engine Start Indicator | Key indicator display | OFF or ON | Customize setting displayed | - |
| Number of Registered Key Codes | Number of registered electrical key transmitter sub-assemblies | 0 to 8 | Number of registered electrical key transmitter sub-assemblies | Up to 7 electrical key transmitter sub-assemblies can be registered. |
| Open in IG2 | History of IG2 input of the steering lock ECU (steering lock actuator or upper bracket assembly) | OK or NG(Past) | OK: History of open in IG2 terminal circuit exists
NG(Past): No history of open in IG2 terminal circuit exists |
When OK is displayed, the steering lock ECU (steering lock actuator or upper bracket assembly) has an IG2 input circuit malfunction. |
| EFI/EV ECU Communication Code Status | Status of EFI communication code | OK or NG | OK: EFI communication code normal
NG: EFI communication code malfunction |
- |
| EFI/EV ECU Communication Status | Status of EFI communication | OK or NG | OK: EFI communication normal
NG: EFI communication malfunction |
- |
| EFI/EV ECU Communication Speed | Status of EFI communication speed | OK or NG | OK: EFI communication speed normal
NG: EFI communication speed malfunction |
- |
| ID-Box Wait Status | Wait status of ID code box | OFF or ON | ON: ID code box waiting
OFF: ID code box not waiting |
- |
*1: This indicates that there is a problem with the communication format between the key and certification ECU (smart key ECU assembly). Wave interference, key or certification ECU (smart key ECU assembly) malfunctions, a key from different vehicle being used, etc. are possible causes.
*2: Hybrid control system start is permitted when it is confirmed that the steering is unlocked and there are no malfunctions in the steering lock system. If hybrid control system start is not permitted, a steering lock ECU (steering lock actuator assembly) malfunction (relay, driver, etc.), an IGE circuit malfunction (wire harness or connector, ID code box (immobiliser code ECU)), or a steering lock sensor malfunction are possible causes.
*3: This indicates that transmission of the wake-up signal is possible ("Yes" indicates that the signal to begin verification-related LIN communication is being sent). When the steering lock motor is operating and an IGE ON signal is received (there is a steering lock operation request), or when communication is being performed between the certification ECU (smart key ECU assembly) and EV control ECU, the display changes to "Yes".
*4: This indicates that the hybrid control system start permission request signal (EGST) output from the EV control ECU is being received by the ID code box (immobiliser code ECU).
*5: This indicates the certification results of the certification codes of the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU).
*6: This indicates the certification results of the certification codes of the ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly).
When the steering lock ECU (steering lock actuator assembly) receives an unlock request from the certification ECU (smart key ECU assembly), confirmation of the ID code box (immobiliser code ECU) L code is performed. If the L code matches, the steering lock ECU (steering lock actuator assembly) unlocks the steering. Also, if the S code verification result does not match, the steering lock will not be unlocked.
*7: The certification ECU (smart key ECU assembly) outputs a steering unlock request for 10 seconds after the ignition switch is turned to ACC or to ON, or a hybrid control system start operation is performed.
*8: The certification ECU (smart key ECU assembly) outputs a steering lock request for 10 seconds after the ignition switch is turned off and any door is opened with the shift lever in P.
*9: Please refer to the following Data List of the actual vehicle.
*1: Press the power switch with the brake pedal released and check that the ignition switch turns to ACC.
*2: Press the power switch with the brake pedal released and check that the ignition switch turns to ON.
*3: Press the power switch with the brake pedal released and check that the hybrid control system starts.
*4: Press the power switch and check that the ignition switch turns off.
*5: Open the driver side door and check that the steering locks.
When the following condition is met, the unlock operation is performed.
When the ignition switch is turned to ACC or to ON and the key and certification ECU (smart key ECU assembly) are verified, the steering is unlocked.
When any of the following conditions are met with ignition switch ACC or ON, key verification is performed.
The brake pedal is depressed so that the hybrid control system can be started.
30 seconds have elapsed after opening and closing a door.
The power switch is pressed.
When the following conditions are met and the certification ECU (smart key ECU assembly) has been verified, the lock operation is performed.
The ignition switch is off.
The shift state is park (P).
A door is opened or a door lock operation (door lock, wireless door lock or key-linked lock) is performed.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed Meter | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy SW | Courtesy light switch RH signal | OFF or ON | OFF: Front door RH closed
ON: Front door RH open |
- |
| FL Door Courtesy SW | Courtesy light switch LH signal | OFF or ON | OFF: Front door LH closed
ON: Front door LH open |
- |
Enter the following menus: Powertrain / EV/ Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Switch | Brake pedal signal | OFF or ON | OFF: Brake pedal released
ON: Brake pedal depressed |
- |
ACTIVE TEST
Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Perform Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| P Supply for Steering Lock | Power supply from certification ECU (smart key ECU assembly) to steering lock ECU (steering lock actuator or upper bracket assembly) | OFF/ON | Ignition switch ON |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Immobiliser Indicator | Security indicator light | OFF/ON | - |