Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2284  Brake Signal Malfunction  


DESCRIPTION

This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B2284 Brake Signal Malfunction The brake signal sent via direct line and the brake signal sent via CAN communication do not match. (1-trip detection logic*)
·

Electronically controlled brake system

·

Stop light switch assembly

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Power Source Control A
DTC Output Confirmation Operation:

Connect the cable to the negative (-) auxiliary battery terminal, release the brake pedal and wait at least 20 seconds. Then depress the brake pedal for 20 seconds or more.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
With the electrical key transmitter sub-assembly in the cabin, even if a hybrid control system start operation is performed, the hybrid control system does not start (the key indicator display is not displayed on the multi-information display). However, the hybrid control system can be started by turning the ignition switch to ACC and then pressing and holding it.
·

If there is a malfunction when the brake signal sent via direct line is on, the hybrid control system can be started by pressing the power switch with the brake pedal released.

·

If there is a malfunction when the brake signal sent via direct line is off, the hybrid control system cannot be started by pressing the power switch with the brake pedal depressed.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2284
Power Source Control
·

Stop Light Switch1



WIRING DIAGRAM

C450542E09
4.813,0.49 5.427,0.688 0.615,0.198 10 false STP1 5.302,0.729 5.552,0.938 0.25,0.208 10 false IC 5.875,2.302 6.49,2.5 0.615,0.198 10 false STP 4.781,3.542 5.396,3.74 0.615,0.198 10 false STP 4.771,4.771 5.385,4.969 0.615,0.198 10 false STP 1.719,3.542 2.333,3.74 0.615,0.198 10 false STP 1.729,2.302 2.344,2.5 0.615,0.198 10 false STP 1.719,0.708 1.969,0.917 0.25,0.208 10 false IC 4.521,0.49 4.833,0.688 0.313,0.198 10 false 25 2.26,0.49 2.573,0.688 0.313,0.198 10 false 2 2.031,0.479 2.344,0.677 0.313,0.198 10 false L 2.115,2.188 2.427,2.385 0.313,0.198 10 false 18 2.115,3.417 2.427,3.615 0.313,0.198 10 false 37 4.521,4.635 4.833,4.833 0.313,0.198 10 false 11 4.5,3.417 4.813,3.615 0.313,0.198 10 false 10 5.646,2.188 5.958,2.385 0.313,0.198 10 false 7 0.844,5.24 4.51,5.438 3.667,0.198 10 false : CAN Communication Line 0.833,1.219 1.146,1.417 0.313,0.198 10 false A3 1.094,2.688 1.406,2.885 0.313,0.198 10 false D93 0.563,3.781 0.99,3.979 0.427,0.198 10 false A5 4.177,1.583 4.49,1.781 0.313,0.198 10 false G37 5.75,2.74 6.385,2.969 0.635,0.229 10 false A17 4.26,3.771 4.792,3.979 0.531,0.208 10 false G102 4.281,5.021 4.75,5.219 0.469,0.198 10 false A6 0.823,1.396 2.688,1.635 1.865,0.24 10 false Stop Light Switch Assembly 1.083,2.865 2.302,3.094 1.219,0.229 10 false Shift Control ECU 0.563,3.969 2.979,4.385 2.417,0.417 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.271,5.198 6.198,5.604 1.927,0.406 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 4.271,3.948 6.021,4.344 1.75,0.396 10 false No. 3 Semiconductor Power Integration ECU 5.75,2.927 6.896,3.24 1.146,0.313 10 false EV Control ECU 4.177,1.75 5.708,2.167 1.531,0.417 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

NOTICE:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)

Pre-procedure1

a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A17 EV control ECU connector.


c.

Disconnect the D93 shift control ECU connector.


d.

Disconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


e.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.


g.

Disconnect the G102 No. 3 semiconductor power integration ECU connector.


h.

Reconnect the cable from the negative (-) auxiliary battery terminal.


i.

Disconnect the A3 stop light switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G37,A3)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

G37-25 (STP1) - A3-2 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the certification ECU (smart key ECU assembly) connector.


b.

Reconnect the A3 stop light switch assembly connector.


Procedure1

a.
B424431C46
1.479,0.177 1.896,0.427 0.417,0.25 1.083,2 1.333,2 1.333,2 1.344,1.167 false 0.167,0.25 0.479,0.448 0.313,0.198 10 false *a 1.573,0.208 1.885,0.406 0.313,0.198 10 false G37 0.708,1.927 1.271,2.177 0.563,0.25 10 false STP1
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G37)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

G37-25 (STP1) - Body ground Brake pedal released 1 V or less
G37-25 (STP1) - Body ground Brake pedal depressed 9 V or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY