Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM37H0E _58 Vehicle Interior _095303 THEFT DETERRENT / KEYLESS ENTRY _0449817 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the power switch, the certification ECU (smart key ECU assembly) stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B278A Short to GND in Immobiliser System Power Source Circuit Short to GND detected in the power supply of the transponder key amplifier of the power switch (VC5 - VC5) (1 trip detection logic*).
·

Harness or connector

·

Power switch

·

Certification ECU (smart key ECU assembly)


Entry&Start A
DTC Output Confirmation Operation:

With the shift state park (P) and the electrical key transmitter sub-assembly held near the power switch, a hybrid control system start operation is performed by pressing and holding the power switch when the transmitter battery is depleted.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started when transmitter battery is depleted by holding electrical key transmitter sub-assembly near power switch and pressing and holding power switch with shift state park (P). -

Related Data List and Active Test
DTC No. Data List and Active Test
B278A -

WIRING DIAGRAM

B463088E65
0.604,3.25 2.594,3.448 1.99,0.198 10 false Power Switch 0.604,3.104 2.594,3.302 1.99,0.198 10 false D98 5.271,3.25 6.792,3.698 1.521,0.448 10 false Certification ECU (Smart Key ECU Assembly) 5.281,3.094 6.625,3.417 1.344,0.323 10 false D86 5.24,2.323 5.854,2.583 0.615,0.26 10 false AGND 5.24,1.823 5.854,2.083 0.615,0.26 10 false CODE 5.25,1.188 5.865,1.448 0.615,0.26 10 false TXCT 5.25,0.677 5.865,0.938 0.615,0.26 10 false VC5 5.917,1.458 6.531,1.719 0.615,0.26 10 false 5 V 5.927,0.125 6.542,0.385 0.615,0.26 10 false 5 V 1.427,2.302 2.042,2.563 0.615,0.26 10 false AGND 1.427,1.813 2.042,2.073 0.615,0.26 10 false CODE 1.469,1.281 2.083,1.542 0.615,0.26 10 false TXCT 1.542,0.771 2.156,1.031 0.615,0.26 10 false VC5 1.906,2.302 2.198,2.552 0.292,0.25 10 false 6 1.917,1.802 2.208,2.052 0.292,0.25 10 false 8 1.917,1.188 2.208,1.438 0.292,0.25 10 false 7 1.906,0.656 2.198,0.906 0.292,0.25 10 false 10 4.99,2.323 5.281,2.573 0.292,0.25 10 false 11 5.052,1.813 5.344,2.063 0.292,0.25 10 false 6 5.063,1.188 5.354,1.438 0.292,0.25 10 false 5 5.073,0.667 5.365,0.917 0.292,0.25 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Using an oscilloscope, check the waveform.

HINT:

Perform this inspection on the push power switch side.


B602402C01
1.927,0.406 2.271,0.625 0.344,0.219 1.635,2.354 1.865,2.354 1.865,2.354 1.865,1.635 true 2.583,2.344 2.333,2.344 2.333,2.344 2.333,1.646 true 1.042,0.573 1.625,1.031 0.583,0.458 10 false *a 1.979,0.427 2.5,0.656 0.521,0.229 10 false D98 6.51,1.354 7.156,1.74 0.646,0.385 10 false GND 1.323,2.271 1.635,2.469 0.313,0.198 10 false VC5 2.625,2.26 3.188,2.5 0.563,0.24 10 false AGND 4.021,0.375 4.604,0.833 0.583,0.458 10 false *b
*a Component with harness connected
(Power Switch)
*b Waveform


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(D98)Location & Routing

Click Connector(D98)Instrument Panel>Instrument Panel Wire>Power Switch

D98-10 (VC5) - D98-6 (AGND) Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds after power switch pressed 2 V/DIV., 200 ms./DIV. Pulse generation
(See waveform)


OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)

Pre-procedure1

a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D98 power switch connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86,D98)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

Click Connector(D98)Instrument Panel>Instrument Panel Wire>Power Switch

D86-7 (VC5) - D98-10 (VC5) Always Below 1 Ω
D86-7 (VC5) or D98-10 (VC5) - Other terminals and body ground Always 10 kΩ or higher
D86-11 (AGND) - D98-6 (AGND) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the D98 power switch connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

B427583C94
4.531,0.417 4.948,0.667 0.417,0.25 5.406,2.188 5.073,2.188 5.073,2.188 5.073,1.229 true 4.531,2.208 4.74,2.208 4.74,2.208 4.74,1.25 true 0.396,0.177 0.708,0.333 0.313,0.156 10 false *a 4.615,0.458 5.115,0.667 0.5,0.208 10 false D86 5.458,2.115 5.958,2.323 0.5,0.208 10 false VC5 4.115,2.115 4.615,2.323 0.5,0.208 10 false AGND
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D86)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

D86-7 (VC5) - D86-11 (AGND) Ignition switch off, brake pedal not depressed, 30 seconds or more after driver door opened and then closed Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)