These DTCs are stored when there is a CAN communication malfunction between the certification ECU (smart key ECU assembly), EV control ECU, main body ECU (multiplex network body ECU), shift control ECU ,combination meter assembly, No. 2 Skid Control ECU (Brake Actuator Assembly).
Data from the option connector (bus buffer ECU) cannot be received.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| U0103 | Lost Communication with Gear Shift Module "A" | CAN communication error between the certification ECU (smart key ECU assembly) and shift control ECU (1-trip detection logic*) | Shift control ECU | Power Source Control | B | DTC Output Confirmation Operation:
Turn the ignition switch to ON and wait at least 5 seconds. |
| U0129 | Lost Communication with Brake System Control Module | CAN communication error between the certification ECU (smart key ECU assembly) and No. 2 Skid Control ECU (Brake Actuator Assembly) (1-trip detection logic*) | No. 2 skid control ECU (brake actuator assembly) | Entry&Start | B | DTC Output Confirmation Operation:
Always |
| U0140 | Lost Communication with Body Control Module | CAN communication malfunction between certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) (1-trip detection logic*) | Main body ECU (multiplex network body ECU) | Power Source Control | B | DTC Output Confirmation Operation:
Any time |
| U0142 | Lost Communication with Main Body ECU | CAN communication malfunction between certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) (1-trip detection logic*) | Main body ECU (multiplex network body ECU) | Entry&Start | B | DTC Output Confirmation Operation:
Any time |
| U0155 | Lost Communication with Combination Meter | CAN communication malfunction between certification ECU (smart key ECU assembly) and combination meter assembly (1-trip detection logic*) | Combination meter assembly | Entry&Start | B | DTC Output Confirmation Operation:
Turn the ignition switch to ON and wait at least 10 seconds. |
| U0293 | Lost Communication With Hybrid Vehicle/EV Control System | CAN communication error between certification ECU (smart key ECU assembly) and EV control ECU (1-trip detection logic*) | EV control ECU | Power Source Control | B | DTC Output Confirmation Operation:
Turn the ignition switch to ON and wait at least 10 seconds. |
| U1117 | Lost Communication with Accessory Gateway | Data from the option connector (bus buffer ECU) cannot be received | ·
Connector and branch wire of sub bus 2 of option connector (bus buffer ECU) ·
Internal malfunction of option connector (bus buffer ECU) |
Power Source Control | B | DTC Output Confirmation Operation:
Turn the ignition switch to ON and wait at least 10 seconds. |
*: Only detected while a malfunction is present.
| DTC Code | Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|---|
| U0103 | The shift state does not change from park (P) to shift state other than park (P). | - |
| U0129 | Hybrid control system does not start. | - |
| U0140 | The warning (meter buzzer) does not sound and no warning messages displayed on the multi-information display. | - |
| U0142 | ·
Doors cannot be locked or unlocked. ·
The warning (wireless buzzer) does not sound. |
- |
| U0155 | ·
The warning (meter buzzer) does not sound and the meter does not indicate a warning. ·
There is no effect on vehicle behavior. |
- |
| U0293 | The warning (meter buzzer) does not sound and no warning messages displayed on the multi-information display. | - |
| U1117 | The hybrid control system cannot be started using the wireless remote control function. | - |
| DTC No. | Data List and Active Test |
|---|---|
| U0103
U0129 U0140 U0142 U0155 U0293 U1117 |
- |
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
Check for DTCs and note any DTCs that are output.
| Proceed to |
|---|
| NEXT |
NEXT
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING