Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM37H0E _59 Vehicle Exterior _095314 DOOR / HATCH _0452987 REAR DOOR N

DOOR / HATCH  REAR DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·
B276679C41
0.621,1.754 0.818,1.944 0.197,0.19 10 *1 2.535,1.754 2.732,1.944 0.197,0.19 10 *2
*1 Centering Bolt
*2 Standard Bolt


Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 67004 1.INSPECT REAR DOOR PANEL SUB-ASSEMBLY LH

a.

Check that the clearance measurements of areas A to N are within the standard ranges.

B600749N01
2.469,0.292 2.625,0.49 0.156,0.198 10 false A 2.625,0.844 2.781,1.042 0.156,0.198 10 false B 4.479,0.25 4.635,0.448 0.156,0.198 10 false C 4.49,0.823 4.646,1.021 0.156,0.198 10 false D 5.458,1.24 5.615,1.438 0.156,0.198 10 false E 5.396,1.698 5.552,1.896 0.156,0.198 10 false F 6.063,2.99 6.219,3.188 0.156,0.198 10 false G 0.99,4.156 1.146,4.354 0.156,0.198 10 false L 1.479,4.01 1.635,4.208 0.156,0.198 10 false K 3.635,5.51 3.792,5.708 0.156,0.198 10 false J 1.563,2.104 1.719,2.302 0.156,0.198 10 false N 4.135,5.146 4.292,5.344 0.156,0.198 10 false I 6.406,3.292 6.563,3.49 0.156,0.198 10 false H 1,1.781 1.156,1.979 0.156,0.198 10 false M

Standard Clearance:
Area Measurement Area Measurement
A 2.9 to 6.3 mm (0.114 to 0.248 in.) B 0.3 to 4.3 mm (0.012 to 0.169 in.)
C 2.9 to 6.3 mm (0.114 to 0.248 in.) D 0.3 to 4.3 mm (0.012 to 0.169 in.)
E 3.1 to 8.1 mm (0.122 to 0.319 in.) F -2.1 to 2.9 mm (-0.083 to 0.114 in.)
G 2.9 to 5.9 mm (0.114 to 0.232 in.) H -1.5 to 1.5 mm (-0.059 to 0.059 in.)
I 4.0 to 8.0 mm (0.157 to 0.315 in.) J 1.3 to 5.3 mm (0.051 to 0.209 in.)
K 3.1 to 5.5 mm (0.122 to 0.217 in.) L -1.2 to 1.2 mm (-0.047 to 0.047 in.)
M 2.3 to 6.3 mm (0.091 to 0.248 in.) N -0.2 to 0.2 mm (-0.008 to 0.008 in.)



Hide 67004 2.ADJUST REAR DOOR PANEL SUB-ASSEMBLY LH

a.
B600750

Using SST, loosen the hinge bolts on the body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
B600751

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.
B600752

Detach the claw and remove the door lock striker cover.


f.
B600753

Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)