CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH
Disconnect the E25 front multiplex network door ECU LH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E25-1 (GND) - Body ground | Ground | Always | Below 1 Ω |
| E25-3 (SIG) - Body ground | Ignition power supply (IG signal) | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | ||
| E25-4 (CPUB) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| E25-6 (BDR) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
Reconnect the E25 front multiplex network door ECU LH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
|
*: w/ Memory |
|||
| E25-9 (SGND) - Body ground | Ground | Always | Below 1 Ω |
| E25-22 (M1) - E25-26 (MSWE)* | M1 switch signal for seat memory switch LH | M1 switch on | Below 1 V |
| M1 switch off | 11 to 14 V | ||
| E25-23 (M2) - E25-26 (MSWE)* | M2 switch signal for seat memory switch LH | M2 switch on | Below 1 V |
| M2 switch off | 11 to 14 V | ||
| E25-25 (MM) - E25-26 (MSWE)* | SET switch signal for seat memory switch LH | SET switch on | Below 1 V |
| SET switch off | 11 to 14 V | ||
| E25-26 (MSWE) - Body ground* | Ground | Always | Below 1 Ω |
| z29-1 (MV) - Body ground | Vertical mirror motor drive voltage | Mirror surface moving stopped | Below 1 V |
| Mirror surface moving upward | 11 to 14 V | ||
| z29-3 (MR) - Body ground | Power retract mirror motor drive voltage | Outer rear view mirror assembly (driver door) being retracted | 11 to 14 V |
| Outer rear view mirror assembly (driver door) stopped | Below 1 V | ||
| z29-4 (+) - z29-12 (-) | Mirror heater relay drive voltage | Window defogger switch (mirror heater switch ) on | 11 to 14 V |
| Window defogger switch (mirror heater switch ) off | Below 1 V | ||
| z29-5 (VC) - Body ground | Mirror position sensor power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 4.75 to 5.25 V | ||
| z29-6 (VSRL) - Body ground | Mirror position sensor signal | Ignition switch ON | 0 to 5 V |
| z29-9 (MH) - Body ground | Horizontal mirror motor drive voltage | Mirror surface moving left → stopped | 11 to 14 V → Below 1 V |
| z29-10 (M+) - Body ground | Vertical and horizontal mirror motors drive voltage | Mirror surface moving downward → stopped | 11 to 14 V → Below 1 V |
| Mirror surface moving right → stopped | 11 to 14 V → Below 1 V | ||
| z29-11 (MF) - Body ground | Power retract mirror motor drive voltage | Outer rear view mirror assembly returning | 11 to 14 V |
| Outer rear view mirror assembly stopped | Below 1 V | ||
| z29-13 (HSRL) - Body ground | Mirror position sensor signal | Ignition switch ON | 0 to 5 V |
| z29-14 (E1) - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E25-11 (LIN1) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
| E25-12 (LIN2) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH
Disconnect the E7 front multiplex network door ECU LH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E7-1 (GND) - Body ground | Ground | Always | Below 1 Ω |
| E7-3 (SIG) - Body ground | Ignition power supply (IG signal) | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | ||
| E7-4 (CPUB) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| E7-6 (BDR) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
Reconnect the E7 front multiplex network door ECU LH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
|
*: w/ Memory |
|||
| E7-9 (SGND) - Body ground | Ground | Always | Below 1 Ω |
| E7-22 (M1) - E7-26 (MSWE)* | M1 switch signal for seat memory switch LH | M1 switch on | Below 1 V |
| M1 switch off | 11 to 14 V | ||
| E7-23 (M2) - E7-26 (MSWE)* | M2 switch signal for seat memory switch LH | M2 switch on | Below 1 V |
| M2 switch off | 11 to 14 V | ||
| E7-25 (MM) - E7-26 (MSWE)* | SET switch signal for seat memory switch LH | SET switch on | Below 1 V |
| SET switch off | 11 to 14 V | ||
| E7-26 (MSWE) - Body ground* | Ground | Always | Below 1 Ω |
| z28-1 (MV) - Body ground | Vertical mirror motor drive voltage | Mirror surface moving stopped | Below 1 V |
| Mirror surface moving upward | 11 to 14 V | ||
| z28-3 (MR) - Body ground | Power retract mirror motor drive voltage | Outer rear view mirror assembly (driver door) being retracted | 11 to 14 V |
| Outer rear view mirror assembly (driver door) stopped | Below 1 V | ||
| z28-4 (+) - z28-12 (-) | Mirror heater relay drive voltage | Window defogger switch (mirror heater switch ) on | 11 to 14 V |
| Window defogger switch (mirror heater switch ) off | Below 1 V | ||
| z28-5 (VC) - Body ground | Mirror position sensor power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 4.75 to 5.25 V | ||
| z28-6 (VSSR) - Body ground | Mirror position sensor signal | Ignition switch ON | 0 to 5 V |
| z28-9 (MH) - Body ground | Horizontal mirror motor drive voltage | Mirror surface moving left → stopped | 11 to 14 V → Below 1 V |
| z28-10 (M+) - Body ground | Vertical and horizontal mirror motors drive voltage | Mirror surface moving downward → stopped | 11 to 14 V → Below 1 V |
| Mirror surface moving right → stopped | 11 to 14 V → Below 1 V | ||
| z28-11 (MF) - Body ground | Power retract mirror motor drive voltage | Outer rear view mirror assembly returning | 11 to 14 V |
| Outer rear view mirror assembly stopped | Below 1 V | ||
| z28-13 (HSSR) - Body ground | Mirror position sensor signal | Ignition switch ON | 0 to 5 V |
| z28-14 (E1) - Body ground | Ground | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E7-11 (LIN1) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
| E7-12 (LIN2) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |