Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)
RM37H0E _59 Vehicle Exterior _095308 MIRROR (EXT) _0453657 POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror) U

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror)  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Read the Data List according to the display on the GTS.

Body Electrical > Front Left Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 switch signal OFF or ON OFF: Seat memory switch M1 switch off
ON: Seat memory switch M1 switch on
w/ Memory
Seat Memory Switch2 Seat memory switch M2 switch signal OFF or ON OFF: Seat memory switch M2 switch off
ON: seat memory switch LH M2 switch on
w/ Memory
Seat Memory Switch3 Seat memory switch M3 switch signal OFF or ON OFF: Seat memory switch M3 switch off
ON: Seat memory switch M3 switch on
Not applicable
Seat Memory Set SW Seat memory switch SET switch signal OFF or ON OFF: Seat memory switch SET switch off
ON: Seat memory switch SET switch on
w/ Memory
Mirror Memory No.1 Mirror position memorized in memory switch M1 OFF or ON OFF: Not memorized
ON: Memorized
-
Mirror Memory No.2 Mirror position memorized in memory switch M2 OFF or ON OFF: Not memorized
ON: Memorized
-
Mirror Memory No.3 Mirror position memorized in memory switch M3 OFF or ON OFF: Not memorized
ON: Memorized
Not applicable
Mirror Memory No.4 Mirror position memorized in memory switch M4 OFF or ON OFF: Not memorized
ON: Memorized
Not applicable
Mirror Memory No.5 Mirror position memorized in memory switch M5 OFF or ON OFF: Not memorized
ON: Memorized
Not applicable
Mirror Memory No.6 Mirror position memorized in memory switch M6 OFF or ON OFF: Not memorized
ON: Memorized
Not applicable
Mirror Memory(Rev) No.1 Mirror reverse shift-linked position No. 1 memorized OFF or ON OFF: Not memorized
ON: Memorized
-
Mirror Vertical Sensor Vol Vertical mirror position MIN: 0, MAX: 5 V 0 to 5 V -
Mirror Horizontal Sensor Vol Horizontal mirror position MIN: 0, MAX: 5 V 0 to 5 V -
# Codes Number of trouble codes 0 to 255 Number of stored DTCs displayed -
Body Electrical > Front Right Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 switch signal OFF or ON OFF: Seat memory switch M1 switch off
ON: Seat memory switch M1 switch on
w/ Memory
Seat Memory Switch2 Seat memory switch M2 switch signal OFF or ON OFF: Seat memory switch M2 switch off
ON: Seat memory switch M2 switch on
w/ Memory
Seat Memory Switch3 Seat memory switch M3 switch signal OFF or ON OFF: Seat memory switch M3 switch off
ON: Seat memory switch M3 switch on
Not applicable
Seat Memory Set SW seat memory switch RH SET switch signal OFF or ON OFF: seat memory switch RH SET switch off
ON: seat memory switch RH SET switch on
w/ Memory
Mirror Memory No.1 Mirror position memorized in memory switch M1 OFF or ON OFF: Not memorized
ON: Memorized
-
Mirror Memory No.2 Mirror position memorized in memory switch M2 OFF or ON OFF: Not memorized
ON: Memorized
-
Mirror Memory No.3 Mirror position memorized in memory switch M3 OFF or ON OFF: Not memorized
ON: Memorized
Not applicable
Mirror Memory No.4 Mirror position memorized in memory switch M4 OFF or ON OFF: Not memorized
ON: Memorized
Not applicable
Mirror Memory No.5 Mirror position memorized in memory switch M5 OFF or ON OFF: Not memorized
ON: Memorized
Not applicable
Mirror Memory No.6 Mirror position memorized in memory switch M6 OFF or ON OFF: Not memorized
ON: Memorized
Not applicable
Mirror Memory(Rev) No.1 Mirror reverse shift-linked position No. 1 memorized OFF or ON OFF: Not memorized
ON: Memorized
-
Mirror Vertical Sensor Vol Vertical mirror position MIN: 0, MAX: 5 V 0 to 5 V -
Mirror Horizontal Sensor Vol Horizontal mirror position MIN: 0, MAX: 5 V 0 to 5 V -
# Codes Number of trouble codes 0 to 255 Number of stored DTCs displayed -
Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Selection SW (R) Mirror select switch signal for RH mirror OFF or ON OFF: Mirror select switch in the neutral position (off)
ON: Mirror select switch in the R position
-
Mirror Selection SW (L) Mirror select switch signal for LH mirror OFF or ON OFF: Mirror select switch in the neutral position (off)
ON: Mirror select switch in the L position
-
Mirror Position SW (R) Mirror surface adjust switch signal (Right) OFF or ON OFF: Mirror surface adjust switch not pressed right
ON: Mirror surface adjust switch pressed right
Check with the mirror select switch in the L or R position
Mirror Position SW (L) Mirror surface adjust switch signal (Left) OFF or ON OFF: Mirror surface adjust switch not pressed left
ON: Mirror surface adjust switch pressed left
Check with the mirror select switch in the L or R position
Mirror Position SW (Up) Mirror surface adjust switch signal (Up) OFF or ON OFF: Mirror surface adjust switch not pressed up
ON: Mirror surface adjust switch pressed up
Check with the mirror select switch in the L or R position
Mirror Position SW (Dwn) Mirror surface adjust switch signal (Down) OFF or ON OFF: Mirror surface adjust switch not pressed down
ON: Mirror surface adjust switch pressed down
Check with the mirror select switch in the L or R position
Outer Mirror Fold SW Mirror retract switch signal OFF or ON OFF: Mirror retract switch not in retract position
ON: Mirror retract switch in retract position
-
Auto Mirror SW Auto retractable outer mirror switch signal OFF or ON OFF: Auto retractable outer mirror switch off
ON: Auto retractable outer mirror switch on
-
Auto Fold Mirror Function that changes the condition under which the outer mirrors automatically retract ACC, Door Lock or OFF Customized setting displayed -
Reverse Coupled Actuation Mirror Angle Function that turns the reverse shift-linked mirror position memorization function on or off Default Setting or User Setting Customized setting displayed -
Mem SW No. w/KeyID1 Switch linked with key ID1 NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID1
MEM SW1: M1 linked with key ID1
MEM SW2: M2 linked with key ID1
MEM SW3: M3 linked with key ID1
-
Mem SW No. w/KeyID2 Switch linked with key ID2 NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID2
MEM SW1: M1 linked with key ID2
MEM SW2: M2 linked with key ID2
MEM SW3: M3 linked with key ID2
-
Mem SW No. w/KeyID3 Switch linked with key ID3 NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID3
MEM SW1: M1 linked with key ID3
MEM SW2: M2 linked with key ID3
MEM SW3: M3 linked with key ID3
-
Mem SW No. w/KeyID4 Switch linked with key ID4 NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID4
MEM SW1: M1 linked with key ID4
MEM SW2: M2 linked with key ID4
MEM SW3: M3 linked with key ID4
-
Mem SW No. w/KeyID5 Switch linked with key ID5 NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID5
MEM SW1: M1 linked with key ID5
MEM SW2: M2 linked with key ID5
MEM SW3: M3 linked with key ID5
-
Mem SW No. w/KeyID6 Switch linked with key ID6 NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID6
MEM SW1: M1 linked with key ID6
MEM SW2: M2 linked with key ID6
MEM SW3: M3 linked with key ID6
-
Mem SW No. w/KeyID7 Switch linked with key ID7 NONE, MEM SW1, MEM SW2, or MEM SW3 NONE: No switches linked with key ID7
MEM SW1: M1 linked with key ID7
MEM SW2: M2 linked with key ID7
MEM SW3: M3 linked with key ID7
-


ACTIVE TEST


HINT:

Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Front Left Door > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Mirror Up/Down Mirror vertical operation OFF, Down or Up
·

Operate with ignition switch to ON and the vehicle stopped.

·

This test tilts the mirror up or down.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Mirror Right/Left Mirror horizontal operation OFF, Right or Left
·

Operate with ignition switch to ON and the vehicle stopped.

·

This test tilts the mirror right or left.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Mirror Fold/Return Mirror retract operation OFF, Return or Fold
·

Operate with ignition switch to ON and the vehicle stopped.

·

This test activates the Fold / Return.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Mirror Heater Mirror heater operation OFF or ON
·

Operate with ignition switch to ON and the vehicle stopped.

·

This test turns the mirror heater on or off.

·

Mirror heater operation can be confirmed by touch.


Body Electrical > Front Right Door > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Mirror Up/Down Mirror vertical operation OFF, Down or Up
·

Operate with ignition switch to ON and the vehicle stopped.

·

This test tilts the mirror up or down.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Mirror Right/Left Mirror horizontal operation OFF, Right or Left
·

Operate with ignition switch to ON and the vehicle stopped.

·

This test tilts the mirror right or left.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Mirror Fold/Return Mirror retract operation OFF, Return or Fold
·

Operate with ignition switch to ON and the vehicle stopped.

·

This test activates the Fold / Return.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Mirror Heater Mirror heater operation OFF or ON
·

Operate with ignition switch to ON and the vehicle stopped.

·

This test turns the mirror heater on or off.

·

Mirror heater operation can be confirmed by touch.