Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › TOYOTA MULTI OPERATION TOUCH SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0447864 TOYOTA MULTI OPERATION TOUCH SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  TOYOTA MULTI OPERATION TOUCH SYSTEM  Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the integration control sub-assembly.

WIRING DIAGRAM

E444863E04
1.75,0.646 3.583,0.844 1.833,0.198 10 false from Auxiliary Battery 1.448,2.406 3.219,2.625 1.771,0.219 10 false from IG1 P NO. 1 Relay*1 3.604,1.115 4.969,1.406 1.365,0.292 10 false MPX-B D NO. 1*2 3.531,2.708 4.604,2.906 1.073,0.198 10 false IG1 P NO. 2*1 3.771,1.76 4.865,2.021 1.094,0.26 10 false ACC D 5.167,3.74 5.479,3.938 0.313,0.198 10 false E61 5.021,0.542 5.177,0.74 0.156,0.198 10 false 1 5.031,1.458 5.344,1.656 0.313,0.198 10 false 3 5.021,2.406 5.333,2.604 0.313,0.198 10 false 4 4.969,3.198 5.219,3.427 0.25,0.229 10 false 20 5.26,0.667 5.719,0.865 0.458,0.198 10 false B 5.26,1.594 5.875,1.792 0.615,0.198 10 false ACC 5.25,2.521 5.563,2.719 0.313,0.198 10 false IG+ 5.25,3.333 5.865,3.531 0.615,0.198 10 false GND 5.167,3.906 6.344,4.469 1.177,0.563 10 false Integration Control Sub-assembly 1.896,1.573 3.729,1.771 1.833,0.198 10 false from ACC D Relay 3.604,0.833 4.969,1.125 1.365,0.292 10 false MPX-B P NO. 1*1 3.531,2.969 4.604,3.167 1.073,0.198 10 false IG1 D NO. 2*2 0.417,3.969 1.49,4.167 1.073,0.198 10 false *1: for LHD 0.417,4.25 1.49,4.448 1.073,0.198 10 false *2: for RHD 1.448,2.698 3.219,2.917 1.771,0.219 10 false from IG1 D NO. 1 Relay*2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBY POWER SOURCE)
a.

Disconnect the D105 integration control sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D105)Location & Routing

Click Connector(D105)Instrument Panel>Instrument Panel Wire>Integration Control Sub-Assembly

D105-20 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D105)Location & Routing

Click Connector(D105)Instrument Panel>Instrument Panel Wire>Integration Control Sub-Assembly

D105-1 (B) - D105-20 (GND) Ignition switch off 11 to 14 V
D105-3 (ACC) - D105-20 (GND) Ignition switch ACC 11 to 14 V
D105-4 (IG+) - D105-20 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR