This DTC is stored when a microphone signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B157213 | Microphone Circuit Open | Current at terminal MCVD is lower than the malfunction threshold for 10 seconds or more while the ignition switch is ON | ·
Telematics transceiver ·
Telephone microphone assembly ·
Harness or connector |
Telematics | A |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Clear the DTCs.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Disconnect the D68 telematics transceiver connector.
Disconnect the H17 telephone microphone assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D68,H17)Location & Routingewd_type=routing;type=c,c;code=D68,H17 Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiverewd_type=component;type=c;code=D68;pinno=5,6,7,23 Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assemblyewd_type=component;type=c;code=H17;pinno=1,2,4 |
||
| D68-5 (MCVD) - H17-1 (MACC) | Always | Below 1 Ω |
| D68-6 (MCI+) - H17-2 (MCO+) | Always | Below 1 Ω |
| D68-7 (MCI-) - H17-4 (MCO-) | Always | Below 1 Ω |
| D68-23 (SGND) - Body ground | Always | 10 kΩ or higher |
| D68-5 (MCVD) - Body ground | Always | 10 kΩ or higher |
| D68-6 (MCI+) - Body ground | Always | 10 kΩ or higher |
| D68-7 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the telephone microphone assembly but do not disconnect the connectors.
Procedure1
| *a | Component with harness connected
(Telephone Microphone Assembly) |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H17)Location & Routingewd_type=routing;type=c;code=H17 Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assemblyewd_type=component;type=c;code=H17;pinno=1 |
||
| H17-1 (MACC) - Body ground | Ignition switch ON | 4 to 6 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H17)Location & Routingewd_type=routing;type=c;code=H17 Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assemblyewd_type=component;type=c;code=H17;pinno=4 |
||
| H17-4 (MCO-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the telematics transceiver with a new one.
| Proceed to |
|---|
| NEXT |
NEXT