Home › Vehicle Interior › HEATING / AIR CONDITIONING › AMBIENT TEMPERATURE SENSOR
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0448158 AMBIENT TEMPERATURE SENSOR G

HEATING / AIR CONDITIONING  AMBIENT TEMPERATURE SENSOR  INSPECTION  


PROCEDURE

Hide 88790B 1.INSPECT THERMISTOR ASSEMBLY

a.
E445410C03
1.844,0.604 2.167,0.802 0.323,0.198 0.344,0.625 0.344,1.313 true 1.688,3.135 1.896,2.917 1.896,2.917 2.302,2.917 false 2.833,0.969 2.625,0.74 true 2.219,0.99 2.427,0.74 true 0.385,1.688 0.844,1.885 0.458,0.198 10 false 4.0 0.385,1.958 0.844,2.156 0.458,0.198 10 false 3.5 0.385,2.24 0.844,2.438 0.458,0.198 10 false 3.0 0.385,2.531 0.844,2.729 0.458,0.198 10 false 2.5 0.385,2.813 0.844,3.01 0.458,0.198 10 false 2.0 0.375,3.083 0.833,3.281 0.458,0.198 10 false 1.5 0.365,3.365 0.823,3.563 0.458,0.198 10 false 1.0 0.375,3.646 0.833,3.844 0.458,0.198 10 false 0.5 0.385,3.917 0.844,4.115 0.458,0.198 10 false 0.0 0.552,4.031 1.01,4.229 0.458,0.198 10 false 10 1.063,4.031 1.521,4.229 0.458,0.198 10 false 20 1.594,4.042 2.052,4.24 0.458,0.198 10 false 30 2.125,4.042 2.583,4.24 0.458,0.198 10 false 40 2.656,4.042 2.875,4.24 0.219,0.198 10 false 50 3.167,4.042 3.385,4.24 0.219,0.198 10 false 60 0.51,4.188 0.833,4.385 0.323,0.198 10 false (50) 1.021,4.188 1.344,4.385 0.323,0.198 10 false (68) 1.552,4.188 1.875,4.385 0.323,0.198 10 false (86) 2.052,4.188 2.448,4.385 0.396,0.198 10 false (104) 2.583,4.188 3.021,4.396 0.438,0.208 10 false (122) 3.083,4.188 3.427,4.396 0.344,0.208 10 false (140) 1.917,0.219 2.229,0.417 0.313,0.198 10 false *a 0.281,1.313 0.594,1.51 0.313,0.198 10 false *b 1.802,4.396 2.115,4.594 0.313,0.198 10 false *d 0.115,2.76 0.427,2.958 0.313,0.198 10 false *c 2.365,2.833 2.677,3.031 0.313,0.198 10 false *e 1.885,0.615 2.344,0.813 0.458,0.198 10 false A35 2.115,0.979 2.271,1.177 0.156,0.198 10 false + 2.865,0.948 3.021,1.146 0.156,0.198 10 false -
*a Component without harness connected
(Thermistor Assembly)
*b Sensing Portion
*c Resistance (kΩ)
*d Temperature (°C (°F))
*e Allowable Range


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A35)Location & Routing

Click Connector(A35)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Thermistor Assembly

A35-1(-) - A35-2(+) 10°C (50°F) 3.00 to 3.73 kΩ
A35-1(-) - A35-2(+) 15°C (59°F) 2.45 to 2.88 kΩ
A35-1(-) - A35-2(+) 20°C (68°F) 1.95 to 2.30 kΩ
A35-1(-) - A35-2(+) 25°C (77°F) 1.60 to 1.80 kΩ
A35-1(-) - A35-2(+) 30°C (86°F) 1.28 to 1.47 kΩ
A35-1(-) - A35-2(+) 35°C (95°F) 1.00 to 1.22 kΩ
A35-1(-) - A35-2(+) 40°C (104°F) 0.80 to 1.00 kΩ
A35-1(-) - A35-2(+) 45°C (113°F) 0.65 to 0.85 kΩ
A35-1(-) - A35-2(+) 50°C (122°F) 0.50 to 0.70 kΩ
A35-1(-) - A35-2(+) 55°C (131°F) 0.44 to 0.60 kΩ
A35-1(-) - A35-2(+) 60°C (140°F) 0.36 to 0.50 kΩ


NOTICE:
·

Hold the sensor only by its connector. Touching the sensing portion may change the resistance value.

·

Perform the measurement once the sensor has adapted to the ambient temperature.

·

Use a thermometer to detect the ambient temperature of the installation area around the thermistor assembly.



HINT:

As the temperature increases, the resistance decreases (see the graph).


If the result is not as specified, replace the thermistor assembly.