Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › PEDESTRIAN PROTECTION SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0454682 PEDESTRIAN PROTECTION SYSTEM L

SUPPLEMENTAL RESTRAINT SYSTEMS  PEDESTRIAN PROTECTION SYSTEM  PRECAUTION  


CAUTION:

Failure to carry out service procedures in the correct sequence could cause pedestrian protection system parts to unexpectedly deploy and possibly lead to serious injuries. Furthermore, if a mistake is made when servicing pedestrian protection system parts, they may fail to operate when required. Before performing servicing (including installation/removal, inspection and replacement of parts), be sure to read the following precautions.


a.

Furthermore, if a mistake is made when servicing pedestrian protection system parts, they may fail to operate when required. Before performing servicing (including installation/removal, inspection and replacement of parts), be sure to read the following precautions.

·

Airbag ECU assembly

·

Pedestrian detection chamber assembly

·

Pop up hood lifter assembly




PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


a.

When troubleshooting the SRS, always check for DTCs before disconnecting the cable from the negative (-) auxiliary battery terminal.


b.

After turning the ignition switch off, disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

hen disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART





c.
B414103

Before starting work relating to the pedestrian protection system, fitting adjustment of the bumper and removal, installation or replacement of parts near the sensors, wait for at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal.

CAUTION:

The SRS is equipped with a back-up power source. If work is started within 60 seconds of disconnecting the cable from the negative (-) auxiliary battery terminal, the pedestrian protection system parts may deploy.



d.

When the cable is disconnected from the negative (-) auxiliary battery terminal, the memory of various systems will be cleared. Because of this, be sure to make a record of the contents memorized in each system before starting work. When work is finished, adjust each system to its previous state.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE



PRECAUTION FOR DAMAGED VEHICLE


a.

Before using an electric welder on the vehicle, remove the pop up hood lifter.


b.

Before performing repairs, remove the pedestrian protection sensor if any impact is likely to be applied to them during repairs.


c.

Do not expose the pedestrian protection sensor to high temperatures.


d.

As the pop up hood lifter is very hot after being deployed, ensure that all the surrounding wire harnesses and connectors are not damaged.


e.

If the engine hood lock is released after the pop up hood lifter is deployed, the engine hood could be lifted up considerably more than usual.


f.

If there are signs of damage or deformation to the front bumper, check the front bumper energy absorber. If the front bumper energy absorber is damaged, replace it.



GENERAL PRECAUTION


a.

Information labels are attached to the SRS parts. Follow the instructions on the labels.


b.

Never disassemble or attempt to repair any of the pedestrian protection system parts.


c.

If any of the pedestrian protection system parts are dropped, or if any cracks, dents or other defects are found, replace them with new parts.


d.

Never use pedestrian protection system parts from another vehicle. When replacing parts, use new parts.


e.

Do not expose any of the pedestrian protection system parts directly to high temperatures or flames.


f.

If the vehicle has been involved in a minor collision where the pop up hood assembly did not deploy, the pedestrian protection system parts should be inspected before further use of the vehicle.


g.

Do not apply grease, detergent, oil or water to the pedestrian protection system parts. If applied, immediately wipe it off with a dry cloth.


h.

When deploying or storing the pedestrian protection system parts, avoid places with a high temperature and high humidity, and keep them away from electrical noise.


i.

When disposing of the vehicle or an SRS part by itself, deploy it using SST before disposal.

CAUTION:
C376913

Dispose of the pop up hood lifters according to the disposal procedures for each pop up hood lifter.



j.

Never measure the resistance of the pop up hood lifter.

CAUTION:
C371108

The pop up hood lifter may deploy due to the tester input.



k.

Use a voltmeter/ohmmeter with high impedance (minimum = 10 kΩ) for troubleshooting electrical circuits.


l.

Be sure to check the multi-information display and pedestrian protection warning light after checking, removing and installing, or replacing the pop up hood lifter and sensor.



PRECAUTION WHEN REPLACING AIRBAG ECU ASSEMBLY


a.

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE


b.

When replacing the airbag ECU assembly, always check that ECU security key is registerd.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PRECAUTION FOR POP UP HOOD LIFTER


a.

Always place a removed pop up hood lifter with the extended section facing upward.

CAUTION:

Placing the pop up hood lifter with the extended portion facing downward could cause a serious accident if the pop up hood lifter deploys.



b.

When storing the pop up hood lifter, do not place objects on top of them or pile up the pop up hood lifters.



PRECAUTION FOR PEDESTRIAN PROTECTION SENSOR AND FRONT BUMPER ENERGY ABSORBER


a.

When the pop up hood lifters are deployed (including when only a pretensioner or pop up hood lifter operates) due to a collision, be sure to replace all sensors in the vehicle body deformed areas (anywhere in need of repair) and pedestrian airbag ECU assembly.


b.

Replace sensors with new ones even if they are not in the vehicle body deformed areas (anywhere in need of repair) when the vehicle body has been subjected to a large collision and if there are any defects as mentioned below.

i.

The defects are as follows:

·

Cracks in the sensor housing

·

Dents in the sensor housing

·

Chips in the sensor housing

·

Cracks or other damage to the connector

·

Damage to the serial number




c.

When removing and installing the pedestrian protection sensor and airbag ECU assembly connectors, be sure to perform work with the sensors installed to the vehicle.


d.

Do not use a sensor if dropped during operation.


e.

Do not use a sensor if subjected to any strong impact.


f.

Never disassemble or attempt to repair any of the pedestrian protection system parts.


g.

Disconnect and reconnect the connector while supporting the pedestrian detection chamber assembly.


h.

The front bumper energy absorber is part of the pedestrian detection chamber assembly. Therefore, if there are any signs it has been subjected to a strong impact or is deformed, do not use it.



PRECAUTION FOR WIRE HARNESS AND CONNECTOR


a.

All wire harnesses except unexposed harnesses in the engine compartment are colored yellow.


b.

As special connectors are used, be careful when handling them.