Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › AUTOMATIC HIGH BEAM MAIN SWITCH
RM37H0E _95 ADAS / AD _095317 ADVANCED DRIVER ASSISTANCE SYSTEM _0454700 AUTOMATIC HIGH BEAM MAIN SWITCH G

ADVANCED DRIVER ASSISTANCE SYSTEM  AUTOMATIC HIGH BEAM MAIN SWITCH  INSPECTION  


PROCEDURE

Hide 84153 1.INSPECT AUTO HIGH BEAM SWITCH

a.

Inspect the auto high beam switch.

i.
E402227C20
1.49,0.156 1.938,0.385 0.448,0.229 1.021,1.771 1.438,1.354 true 2.344,1.75 2.042,1.354 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 0.854,1.76 1.073,1.917 0.219,0.156 10 false +B 2.365,1.76 2.583,1.917 0.219,0.156 10 false E 1.583,0.188 2.198,0.385 0.615,0.198 10 false D109
*a Component without harness connected
(Auto High Beam Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D109)Location & Routing

Click Connector(D109)Instrument Panel>Instrument Panel Wire>Auto High Beam Switch

D109-5(+B) - D109-2(E) Auto high beam switch OFF 10 kΩ or higher
D109-5(+B) - D109-2(E) Auto high beam switch ON Below 1 Ω


HINT:

If the result is not as specified, replace the auto high beam switch.




b.

Check the illumination.

i.
E402227C21
1.448,0.198 1.906,0.417 0.458,0.219 0.823,1.719 1.208,1.344 true 2.635,1.719 2.271,1.344 true 0.167,0.156 0.479,0.313 0.313,0.156 10 false *a 0.531,1.698 0.844,1.854 0.313,0.156 10 false ILL+ 2.677,1.708 2.99,1.865 0.313,0.156 10 false ILL- 1.531,0.24 2.146,0.438 0.615,0.198 10 false D109
*a Component without harness connected
(Auto High Beam Switch)


Apply auxiliary battery voltage to the auto high beam switch and check that the lights illuminate.

OK:
Tester Connection Specified Condition

Click Location & Routing(D109)Location & Routing

Click Connector(D109)Instrument Panel>Instrument Panel Wire>Auto High Beam Switch

Auxiliary battery positive (+) - Terminal D109-6(ILL+)
Auxiliary battery positive (+) - D109-1(ILL-)
Auto high beam switch lluminates


HINT:

If the result is not as specified, replace the auto high beam switch.




c.

Check the Indicator illumination.

i.
E402227C22
1.406,0.208 1.906,0.448 0.5,0.24 1.229,1.781 1.646,1.365 true 2.188,1.75 1.875,1.354 true 0.156,0.156 0.469,0.313 0.313,0.156 10 false *a 0.99,1.792 1.479,1.969 0.49,0.177 10 false AZBI 2.146,1.771 2.646,1.958 0.5,0.188 10 false IND+ 1.5,0.26 2.115,0.458 0.615,0.198 10 false D109
*a Component without harness connected
(Auto High Beam Switch)


Apply auxiliary battery voltage to the auto high beam switch and check that the Indicator lights illuminate.

OK:
Tester Connection Specified Condition

Click Location & Routing(D109)Location & Routing

Click Connector(D109)Instrument Panel>Instrument Panel Wire>Auto High Beam Switch

Auxiliary battery positive (+) - Terminal D109-3(IND+)
Auxiliary battery positive (+) - D109-4(AZBI)
Auto high beam switch Indicator lluminates


HINT:

If the result is not as specified, replace the auto high beam switch.