Home › Vehicle Interior › SEAT › SEAT MEMORY SWITCH
RM37H0E _58 Vehicle Interior _095292 SEAT _0454728 SEAT MEMORY SWITCH G

SEAT  SEAT MEMORY SWITCH  INSPECTION  


PROCEDURE

Hide 84927C 1.INSPECT SEAT MEMORY SWITCH LH (for LHD)

a.
B607551C03
1.51,2.021 1.896,2.229 0.385,0.208 1.979,2.865 2.385,2.865 true 1.01,2.865 1.417,2.865 true 1.781,2.917 1.917,3.198 true 1.635,2.917 1.51,3.208 true 0.615,2.052 0.927,2.208 0.313,0.156 10 false *a 1.385,3.229 1.625,3.427 0.24,0.198 10 false M1 0.781,2.771 1.083,2.948 0.302,0.177 10 false M2 2.469,2.792 2.625,2.99 0.156,0.198 10 false E 1.802,3.24 2.313,3.427 0.51,0.188 10 false MMRY 1.573,2.042 2.031,2.24 0.458,0.198 10 false E28
*a Component without harness connected
(Seat Memory Switch LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E28)Location & Routing

Click Connector(E28)Body>Front Door Wire LH / Front Door Wire RH>Seat Memory Switch LH

E28-2 (MMRY) - E28-1 (E) SET switch pressed Below 1 Ω
E28-2 (MMRY) - E28-1 (E) SET switch not pressed 10 kΩ or higher
E28-3 (M1) - E28-1 (E) 1 switch pressed Below 1 Ω
E28-3 (M1) - E28-1 (E) 1 switch not pressed 10 kΩ or higher
E28-4 (M2) - E28-1 (E) 2 switch pressed Below 1 Ω
E28-4 (M2) - E28-1 (E) 2 switch not pressed 10 kΩ or higher


If the result is not as specified, replace the seat memory switch LH.


Hide 84927B 2.INSPECT SEAT MEMORY SWITCH RH (for RHD)

a.
B601865C06
1.49,1.99 1.885,2.208 0.396,0.219 1.979,2.865 2.385,2.865 true 1.01,2.865 1.417,2.865 true 1.781,2.917 1.917,3.198 true 1.635,2.917 1.51,3.208 true 0.615,2.052 0.927,2.208 0.313,0.156 10 false *a 0.813,2.802 1.083,2.969 0.271,0.167 10 false M2 1.76,3.229 2.24,3.427 0.479,0.198 10 false MMRY 2.469,2.792 2.625,2.99 0.156,0.198 10 false E 1.417,3.229 1.927,3.417 0.51,0.188 10 false M1 1.573,2.031 2.031,2.229 0.458,0.198 10 false E10
*a Component without harness connected
(Seat Memory Switch RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E10)Location & Routing

Click Connector(E10)Body>Front Door Wire LH / Front Door Wire RH>Seat Memory Switch RH

E10-2 (MMRY) - E10-1 (E) SET switch pressed Below 1 Ω
E10-2 (MMRY) - E10-1 (E) SET switch not pressed 10 kΩ or higher
E10-3 (M1) - E10-1 (E) 1 switch pressed Below 1 Ω
E10-3 (M1) - E10-1 (E) 1 switch not pressed 10 kΩ or higher
E10-4 (M2) - E10-1 (E) 2 switch pressed Below 1 Ω
E10-4 (M2) - E10-1 (E) 2 switch not pressed 10 kΩ or higher


If the result is not as specified, replace the seat memory switch RH.