Home › Vehicle Interior › SEAT BELT › FRONT SEAT INNER BELT ASSEMBLY › 2020.11–2021.08
RM37H0E _58 Vehicle Interior _095297 SEAT BELT _0448139 FRONT SEAT INNER BELT ASSEMBLY G

SEAT BELT  FRONT SEAT INNER BELT ASSEMBLY  INSPECTION  


PROCEDURE

Hide 73240 1.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH (for LHD)

a.

Measure the resistance according to the value(s) in the table below.

B509839C05
4.927,0.615 5.344,0.833 0.417,0.219 1.688,0.573 2.104,0.792 0.417,0.219 5.583,2 5.313,1.5 true 4.865,2.01 5.135,1.5 true 0.188,0.115 0.5,0.271 0.313,0.156 10 false *a 1.844,0.583 2.156,0.74 0.313,0.156 10 false A 5.594,2.031 5.75,2.229 0.156,0.198 10 false E 4.802,2.031 4.958,2.229 0.156,0.198 10 false + 5,0.646 5.458,0.844 0.458,0.198 10 false G24
*a Component without harness connected
(Front Seat Inner Belt Assembly LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G24)Location & Routing

Click Connector(G24)Seat>Floor Wire>Front Seat Inner Belt Assembly LH

A-1 - G24-2 (E) Seat belt unfastened 10 kΩ or higher
A-1 - A-2 Seat belt unfastened 10 kΩ or higher
A-2 - G24-3 (+) Seat belt unfastened Below 1 Ω
G24-2 (E) - G24-3 (+) Seat belt unfastened Below 1 Ω
A-1 - G24-2 (E) Seat belt fastened Below 1 Ω
A-1 - A-2 Seat belt fastened Below 1 Ω
A-2 - G24-3 (+) Seat belt fastened 10 kΩ or higher
G24-2 (E) - G24-3 (+) Seat belt fastened 10 kΩ or higher


If the result is not as specified, replace the front seat inner belt assembly LH.


Hide 73230 2.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH (for LHD)

a.

w/ All Auto Control:

i.

Measure the resistance according to the value(s) in the table below.

B607205C03
2.042,0.427 2.51,0.688 0.469,0.26 4.802,0.698 5.271,0.958 0.469,0.26 2.646,1.188 3.292,1.188 true 2.646,1.531 3.198,1.792 true 2.292,1.542 2.313,2.26 true 1.938,1.531 1.448,1.948 true 0.219,0.146 0.531,0.344 0.313,0.198 10 false *a 2.135,0.469 2.594,0.667 0.458,0.198 10 false G27 4.979,0.74 5.292,0.938 0.313,0.198 10 false A 3.354,1.104 3.667,1.302 0.313,0.198 10 false RDC 3.26,1.719 3.573,1.917 0.313,0.198 10 false E 2.281,2.302 2.594,2.5 0.313,0.198 10 false E 1.333,1.938 1.646,2.135 0.313,0.198 10 false +
*a Component without harness connected
(Front Seat Inner Belt Assembly RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G27)Location & Routing

Click Connector(G27)Seat>Floor Wire>Front Seat Inner Belt Assembly RH

G27-1 (RDC) - G27-4 (E) Seat belt unfastened 10 kΩ or higher
G27-1 (RDC) - G27-4 (E) Seat belt fastened Below 1 Ω
G27-5 (E) - A-3 Always Below 1 Ω
G27-6 (+) - A-1 Always Below 1 Ω


If the result is not as specified, replace the front seat inner belt assembly RH.



b.

w/o All Auto Control:

i.

Measure the resistance according to the value(s) in the table below.

B607204C02
2.083,0.563 2.552,0.823 0.469,0.26 4.802,0.719 5.271,0.979 0.469,0.26 3.01,2.167 2.667,1.521 true 2.646,2.198 2.458,1.521 true 1.979,2.188 2.146,1.531 true 1.75,2.083 1.969,1.531 true 2.302,2.208 2.323,1.51 true 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 4.979,0.76 5.292,0.958 0.313,0.198 10 false A 2.177,0.604 2.49,0.802 0.313,0.198 10 false G28 2.927,2.208 3.24,2.406 0.313,0.198 10 false RDC 2.625,2.229 2.938,2.427 0.313,0.198 10 false E 1.917,2.219 2.229,2.417 0.313,0.198 10 false E 1.656,2.073 1.969,2.271 0.313,0.198 10 false + 2.25,2.208 2.563,2.406 0.313,0.198 10 false +
*a Component without harness connected
(Front Seat Inner Belt Assembly RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G28)Location & Routing

Click Connector(G28)Seat>Floor Wire>Front Seat Inner Belt Assembly RH

G28-1 (RDC) - G28-2 (E) Seat belt unfastened 10 kΩ or higher
G28-3 (+) - G28-2 (E) Seat belt unfastened Below 1 Ω
G28-1 (RDC) - G28-2 (E) Seat belt fastened Below 1 Ω
G28-3 (+) - G28-2 (E) Seat belt fastened 10 kΩ or higher
G28-4 (E) - A-3 Always Below 1 Ω
G28-5 (+) - A-1 Always Below 1 Ω


If the result is not as specified, replace the front seat inner belt assembly RH.



Hide 73230 3.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH (for RHD)

a.

Measure the resistance according to the value(s) in the table below.

B509839C06
4.927,0.615 5.344,0.833 0.417,0.219 1.698,0.563 2.115,0.781 0.417,0.219 5.583,2 5.313,1.5 true 4.865,2.01 5.135,1.5 true 0.188,0.115 0.5,0.271 0.313,0.156 10 false *a 1.844,0.583 2.156,0.74 0.313,0.156 10 false A 5.594,2.031 5.75,2.229 0.156,0.198 10 false E 4.802,2.031 4.958,2.229 0.156,0.198 10 false + 5,0.646 5.458,0.844 0.458,0.198 10 false G22
*a Component without harness connected
(Front Seat Inner Belt Assembly RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G22)Location & Routing

Click Connector(G22)Seat>Floor Wire>Front Seat Inner Belt Assembly RH

A-1 - G22-2 (E) Seat belt unfastened 10 kΩ or higher
A-1 - A-2 Seat belt unfastened 10 kΩ or higher
A-2 - G22-3 (+) Seat belt unfastened Below 1 Ω
G22-2 (E) - G22-3 (+) Seat belt unfastened Below 1 Ω
A-1 - G22-2 (E) Seat belt fastened Below 1 Ω
A-1 - A-2 Seat belt fastened Below 1 Ω
A-2 - G22-3 (+) Seat belt fastened 10 kΩ or higher
G22-2 (E) - G22-3 (+) Seat belt fastened 10 kΩ or higher


If the result is not as specified, replace the front seat inner belt assembly RH.


Hide 73240 4.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH (for RHD)

a.

w/ All Auto Control:

i.

Measure the resistance according to the value(s) in the table below.

B607205C01
2.042,0.427 2.51,0.688 0.469,0.26 4.813,0.698 5.281,0.958 0.469,0.26 2.646,1.188 3.292,1.188 true 2.646,1.531 3.198,1.792 true 2.292,1.542 2.313,2.26 true 1.938,1.531 1.448,1.948 true 0.219,0.146 0.531,0.344 0.313,0.198 10 false *a 2.135,0.469 2.594,0.667 0.458,0.198 10 false G25 4.99,0.74 5.302,0.938 0.313,0.198 10 false A 3.354,1.104 3.667,1.302 0.313,0.198 10 false RDC 3.26,1.719 3.573,1.917 0.313,0.198 10 false E 2.281,2.302 2.594,2.5 0.313,0.198 10 false E 1.333,1.938 1.646,2.135 0.313,0.198 10 false +
*a Component without harness connected
(Front Seat Inner Belt Assembly LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G25)Location & Routing

Click Connector(G25)Seat>Floor Wire>Front Seat Inner Belt Assembly LH

G25-1 (RDC) - G25-4 (E) Seat belt unfastened 10 kΩ or higher
G25-1 (RDC) - G25-4 (E) Seat belt fastened Below 1 Ω
G25-5 (E) - A-3 Always Below 1 Ω
G25-6 (+) - A-1 Always Below 1 Ω


If the result is not as specified, replace the front seat inner belt assembly LH.



b.

w/o All Auto Control:

i.

Measure the resistance according to the value(s) in the table below.

B607204C01
2.083,0.563 2.552,0.823 0.469,0.26 4.802,0.698 5.271,0.958 0.469,0.26 3.01,2.167 2.667,1.521 true 2.646,2.198 2.458,1.521 true 1.979,2.188 2.146,1.531 true 1.75,2.083 1.969,1.531 true 2.302,2.208 2.323,1.51 true 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 4.99,0.76 5.302,0.958 0.313,0.198 10 false A 2.177,0.604 2.49,0.802 0.313,0.198 10 false G26 2.927,2.208 3.24,2.406 0.313,0.198 10 false RDC 2.625,2.229 2.938,2.427 0.313,0.198 10 false E 1.917,2.219 2.229,2.417 0.313,0.198 10 false E 1.656,2.073 1.969,2.271 0.313,0.198 10 false + 2.25,2.208 2.563,2.406 0.313,0.198 10 false +
*a Component without harness connected
(Front Seat Inner Belt Assembly LH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G26)Location & Routing

Click Connector(G26)Seat>Floor Wire>Front Seat Inner Belt Assembly LH

G26-1 (RDC) - G26-2 (E) Seat belt unfastened 10 kΩ or higher
G26-3 (+) - G26-2 (E) Seat belt unfastened Below 1 Ω
G26-1 (RDC) - G26-2 (E) Seat belt fastened Below 1 Ω
G26-3 (+) - G26-2 (E) Seat belt fastened 10 kΩ or higher
G26-4 (E) - A-3 Always Below 1 Ω
G26-5 (+) - A-1 Always Below 1 Ω


If the result is not as specified, replace the front seat inner belt assembly LH.