Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0453794 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1574  GVIF Disconnected (from Park Assist/Monitoring ECU to EMV/MM Integrated Device)  


DESCRIPTION

The multi-display assembly and parking assist ECU are connected via video signal (digital) lines.

This DTC is stored when a video signal (digital) line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1574 GVIF Disconnected (from Park Assist/Monitoring ECU to EMV/MM Integrated Device) GVIF disconnected (from parking assist ECU to multi-display assembly)
·

Harness or connector (GVIF cable)

·

Multi-display assembly

·

Parking assist ECU


Navigation System A

WIRING DIAGRAM

E381479E96
1.208,3.135 2.646,3.458 1.438,0.323 10 false : GVIF Cable 1.25,2.354 1.75,2.573 0.5,0.219 10 false D154 1.25,2.542 2.813,2.76 1.563,0.219 10 false Multi-display Assembly 2.073,0.813 2.573,1.031 0.5,0.219 10 false GVO+ 2.073,1.969 2.573,2.188 0.5,0.219 10 false GVG1 4.927,2.375 5.427,2.594 0.5,0.219 10 false G138 4.938,2.552 6.615,2.792 1.677,0.24 10 false Parking Assist ECU 4.875,1.229 5.375,1.448 0.5,0.219 10 false 2 4.885,0.667 5.385,0.885 0.5,0.219 10 false 1 4.865,1.865 5.365,2.083 0.5,0.219 10 false 3 2.094,1.365 2.594,1.583 0.5,0.219 10 false GVO- 5.073,1.969 5.573,2.188 0.5,0.219 10 false GVG1 2.552,0.688 3.052,0.906 0.5,0.219 10 false 1 2.563,1.229 3.063,1.448 0.5,0.219 10 false 2 2.573,1.833 3.073,2.052 0.5,0.219 10 false 3 5.073,1.365 5.573,1.583 0.5,0.219 10 false GVO- 5.063,0.823 5.563,1.042 0.5,0.219 10 false GVO+ 3.698,1.813 4.198,2.031 0.5,0.219 10 false * 5.208,3.167 6.885,3.406 1.677,0.24 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

b.

Change the shift position to R and check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

None



A

B

2.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - PARKING ASSIST ECU)
2.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - PARKING ASSIST ECU)

Pre-procedure1

a.

Disconnect the D154 multi-display assembly connector.


b.

Disconnect the G138 parking assist ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D154,G138)Location & Routing

Click Connector(D154)Instrument Panel>Instrument Panel Wire>Multi-Display Assembly

Click Connector(G138)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECU

D154-1 (GVO+) - G138-1 (GVO+) Always Below 1 Ω
D154-2 (GVO-) - G138-2 (GVO-) Always Below 1 Ω
D154-3 (GVG1) - G138-3 (GVG1) Always Below 1 Ω
D154-1 (GVO+) or G138-1 (GVO+) - Body ground Always 10 kΩ or higher
D154-2 (GVO-) or G138-2 (GVO-) - Body ground Always 10 kΩ or higher
D154-3 (GVG1) or G138-3 (GVG1) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MULTI-DISPLAY ASSEMBLY

Pre-procedure1

a.

Replace the multi-display assembly with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY>REMOVAL



b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

c.

Change the shift position to R and check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

d.

None



A

END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

B