Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0453794 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Telephone microphone assembly

·

Radio receiver assembly

·

Telematics transceiver*

·

Harness or connector


Navigation System A

·

*: w/ Telematics Transceiver


WIRING DIAGRAM

E384811E26
0.135,0.104 2.292,0.323 2.156,0.219 12 false w/ Telematics Transceiver: 1.292,1.042 1.75,1.229 0.458,0.188 10 false SNS2 1.292,2 1.75,2.188 0.458,0.188 10 false MCO- 3.25,2 3.708,2.188 0.458,0.188 10 false MCI- 5.781,1.052 6.24,1.24 0.458,0.188 10 false SNS2 0.688,2.594 1.146,2.781 0.458,0.188 10 false H17 0.688,2.75 2.792,2.948 2.104,0.198 10 false Telephone Microphone Assembly 3.073,2.563 3.531,2.75 0.458,0.188 10 false D68 3.073,2.74 5.031,2.927 1.958,0.188 10 false Telematics Transceiver 5.49,2.552 5.948,2.74 0.458,0.188 10 false D64 5.49,2.729 7.125,2.927 1.635,0.198 10 false Radio Receiver Assembly 1.802,0.927 1.938,1.125 0.135,0.198 10 false 3 1.813,1.875 1.948,2.073 0.135,0.198 10 false 4 2.979,1.885 3.188,2.083 0.208,0.198 10 false 7 5.49,0.927 5.698,1.125 0.208,0.198 10 false 25

E379999E39
0.115,0.125 2.385,0.365 2.271,0.24 12 false w/o Telematics Transceiver: 1.302,1.052 1.76,1.281 0.458,0.229 10 false SNS2 1.813,0.927 2.031,1.115 0.219,0.188 10 false 3 5.448,0.927 5.667,1.115 0.219,0.188 10 false 25 5.771,1.042 6.49,1.333 0.719,0.292 10 false SNS2 1.292,2.042 1.75,2.271 0.458,0.229 10 false MCO- 1.823,1.927 2.281,2.156 0.458,0.229 10 false 4 5.448,1.948 5.729,2.188 0.281,0.24 10 false 22 5.781,2.063 6.24,2.292 0.458,0.229 10 false MIN- 5.74,2.604 6.198,2.833 0.458,0.229 10 false D64 5.75,2.781 6.688,3.177 0.938,0.396 10 false Radio Receiver Assembly 0.823,2.563 1.281,2.792 0.458,0.229 10 false H7 0.823,2.74 2.25,3.229 1.427,0.49 10 false Telephone Microphone Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one. (w/ Telematics Transceiver)



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Telematics Transceiver A
w/o Telematics Transceiver B



A

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

Pre-procedure1

a.

Disconnect the D64 radio receiver assembly connector.


b.

Disconnect the H17 telephone microphone assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D64,H17)Location & Routing

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assembly

D64-25 (SNS2) - H17-3 (SNS2) Always Below 1 Ω
D64-25 (SNS2) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - TELEPHONE MICROPHONE ASSEMBLY)

Pre-procedure1

a.

Disconnect the D68 telematics transceiver connector.


b.

Disconnect the H17 telephone microphone assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D68,H17)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assembly

D68-7 (MCI-) - H17-4 (MCO-) Always Below 1 Ω
D68-7 (MCI-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.CHECK TELEMATICS TRANSCEIVER (MCI-)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TELEMATICS TRANSCEIVER (MCI-)

Pre-procedure1

a.
E427105C60
1.583,0.479 1.99,0.76 0.406,0.281 2.24,1.698 2.458,0.948 2.458,0.948 2.635,0.948 true 1.677,0.542 2.156,0.771 0.479,0.229 10 false D68 2.698,0.875 3.156,1.073 0.458,0.198 10 false MCI- 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a
*a Component with harness connected
(Telematics Transceiver)


Remove the telematics transceiver with the connector(s) still connected.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D68)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D68-7 (MCI-) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

5.INSPECT TELEPHONE MICROPHONE ASSEMBLY (SNS2, MCO-)

NG

5.INSPECT TELEPHONE MICROPHONE ASSEMBLY (SNS2, MCO-)

Pre-procedure1

a.

Remove the telephone microphone assembly.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL



Procedure1

b.
E364293N01
1.76,1.229 2.01,0.458 2.01,0.458 2.198,0.458 true 1.458,1.229 1.188,0.469 1.188,0.469 0.958,0.469 true 2.26,0.385 2.698,0.552 0.438,0.167 10 false SNS2 0.542,0.375 0.958,0.552 0.417,0.177 10 false MCO-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SNS2) - 4 (MCO-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

Pre-procedure1

a.

Disconnect the D64 radio receiver assembly connector.


b.

Disconnect the H17 telephone microphone assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D64,H17)Location & Routing

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assembly

D64-25 (SNS2) - H17-3 (SNS2) Always Below 1 Ω
D64-22 (MIN-) - H17-4 (MCO-) Always Below 1 Ω
D64-25 (SNS2) - Body ground Always 10 kΩ or higher
D64-22 (MIN-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

7.INSPECT TELEPHONE MICROPHONE ASSEMBLY (SNS2, MCO-)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT TELEPHONE MICROPHONE ASSEMBLY (SNS2, MCO-)

Pre-procedure1

a.

Remove the telephone microphone assembly.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL



Procedure1

b.
E364293N01
1.76,1.229 2.01,0.458 2.01,0.458 2.198,0.458 true 1.458,1.229 1.188,0.469 1.188,0.469 0.958,0.469 true 2.26,0.385 2.698,0.552 0.438,0.167 10 false SNS2 0.542,0.375 0.958,0.552 0.417,0.177 10 false MCO-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SNS2) - 4 (MCO-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPLACE TELEPHONE MICROPHONE ASSEMBLY