Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0453794 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The radio receiver assembly and stereo component amplifier assembly are connected via MOST communication lines.

When a MOST communication error occurs between the radio receiver assembly and stereo component amplifier assembly, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15D3 Stereo Component Amplifier Disconnected A device that is listed in the MOST network connected device record of the master unit is missing.
·

Stereo component amplifier assembly power source circuit

·

MOST circuit between radio receiver assembly and stereo component amplifier assembly

·

Stereo component amplifier assembly

·

Radio receiver assembly

·

Harness or connector


Navigation System B

HINT:

For the MOST network, the radio receiver assembly is the master unit.


WIRING DIAGRAM

E456923E01
1.438,0.271 4.802,0.469 3.365,0.198 10 false from Auxiliary Battery 3.625,0.844 4.552,1.135 0.927,0.292 10 false AMP NO. 2 6.271,0.688 6.792,0.896 0.521,0.208 10 false 18 6.313,0.292 6.719,0.51 0.406,0.219 10 false 3 5.802,0.479 6.729,0.771 0.927,0.292 10 false GND 4.677,1.365 5.604,1.656 0.927,0.292 10 false G111 1.688,1.365 2.615,1.656 0.927,0.292 10 false MO+ 1.708,1.781 2.635,2.073 0.927,0.292 10 false MO- 1.625,2.208 2.552,2.5 0.927,0.292 10 false SLDO 1.76,2.625 2.688,2.917 0.927,0.292 10 false MI+ 1.792,3.042 2.719,3.333 0.927,0.292 10 false MI- 1.688,3.469 2.615,3.76 0.927,0.292 10 false SLDI 2.104,1.219 3.031,1.51 0.927,0.292 10 false 5 2.104,1.625 3.031,1.917 0.927,0.292 10 false 6 2.104,2.083 3.031,2.375 0.927,0.292 10 false 7 2.104,2.458 3.031,2.75 0.927,0.292 10 false 2 2.104,2.865 3.031,3.156 0.927,0.292 10 false 3 2.104,3.344 3.031,3.635 0.927,0.292 10 false 4 4.802,1.167 5.729,1.458 0.927,0.292 10 false 2 4.792,1.594 5.719,1.885 0.927,0.292 10 false 3 4.792,2.01 5.719,2.302 0.927,0.292 10 false 4 4.792,2.417 5.719,2.708 0.927,0.292 10 false 5 4.792,2.844 5.719,3.135 0.927,0.292 10 false 6 4.802,3.26 5.729,3.552 0.927,0.292 10 false 7 0.948,5.344 4.104,5.646 3.156,0.302 10 false : MOST Communication Line 5.115,0.667 6.042,0.958 0.927,0.292 10 false +B2 5.104,1.375 6.031,1.667 0.927,0.292 10 false MI+ 5.115,1.802 6.042,2.094 0.927,0.292 10 false MI- 5.115,2.208 6.042,2.5 0.927,0.292 10 false SLDI 5.104,2.635 6.031,2.927 0.927,0.292 10 false MO+ 5.104,3.052 6.031,3.344 0.927,0.292 10 false MO- 5.104,3.479 6.031,3.771 0.927,0.292 10 false SLDO 3.323,2.01 3.677,2.271 0.354,0.26 10 false * 3.323,3.281 3.677,3.542 0.354,0.26 10 false * 0.615,3.885 1.042,4.073 0.427,0.188 10 false D142 0.615,4.063 2.448,4.771 1.833,0.708 10 false Radio Receiver Assembly 5.031,3.885 6.25,4.781 1.219,0.896 10 false Stereo Component Amplifier Assembly 0.365,4.833 2.292,5.094 1.927,0.26 10 false *: Shielded 5.74,0.885 6.667,1.177 0.927,0.292 10 false GND2 5.104,0.271 6.031,0.563 0.927,0.292 10 false +B 3.625,0.427 4.552,0.719 0.927,0.292 10 false AMP NO. 1 4.802,0.063 5.729,0.354 0.927,0.292 10 false 1 4.729,0.271 5.656,0.563 0.927,0.292 10 false G54 4.771,0.479 5.698,0.771 0.927,0.292 10 false 16 4.729,0.667 5.656,0.958 0.927,0.292 10 false G54 6.229,0.49 7.156,0.781 0.927,0.292 10 false G54 6.229,0.896 7.156,1.188 0.927,0.292 10 false G54 4.688,1.792 5.615,2.083 0.927,0.292 10 false G111 4.688,2.198 5.615,2.49 0.927,0.292 10 false G111 4.677,2.635 5.604,2.927 0.927,0.292 10 false G111 4.677,3.042 5.604,3.333 0.927,0.292 10 false G111 4.677,3.469 5.604,3.76 0.927,0.292 10 false G111

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC
a.

If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.


Result:
Result Proceed to
B15C3 is not output A
B15C3 is output B



A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.

·

This DTC may be stored when a MOST communication error occurs due to electrical noise.




Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B



A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

None



A

END

B

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)

Pre-procedure1

a.

Disconnect the G54 stereo component amplifier assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G54)Location & Routing

Click Connector(G54)Body>Floor Wire / No. 3 Floor Wire>Stereo Component Amplifier Assembly

G54-3 (GND) - Body ground Always Below 1 Ω
G54-18 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G54)Location & Routing

Click Connector(G54)Body>Floor Wire / No. 3 Floor Wire>Stereo Component Amplifier Assembly

G54-1 (+B) - G54-3 (GND) Ignition switch off 11 to 14 V
G54-16 (+B2) - G54-3 (GND) Ignition switch off 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the D142 radio receiver assembly connector.


b.

Disconnect the G111 stereo component amplifier assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D142,G111)Location & Routing

Click Connector(D142)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(G111)Body>Floor Wire / No. 3 Floor Wire>Stereo Component Amplifier Assembly

D142-5 (MO+) - G111-2 (MI+) Always Below 1 Ω
D142-6 (MO-) - G111-3 (MI-) Always Below 1 Ω
D142-7 (SLDO) - G111-4 (SLDI) Always Below 1 Ω
D142-2 (MI+) - G111-5 (MO+) Always Below 1 Ω
D142-3 (MI-) - G111-6 (MO-) Always Below 1 Ω
D142-4 (SLDI) - G111-7 (SLDO) Always Below 1 Ω
D142-5 (MO+) or G111-2 (MI+) - Body ground Always 10 kΩ or higher
D142-6 (MO-) or G111-3 (MI-) - Body ground Always 10 kΩ or higher
D142-7 (SLDO) or G111-4 (SLDI) - Body ground Always 10 kΩ or higher
D142-2 (MI+) or G111-5 (MO+) - Body ground Always 10 kΩ or higher
D142-3 (MI-) or G111-6 (MO-) - Body ground Always 10 kΩ or higher
D142-4 (SLDI) or G111-7 (SLDO) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

Pre-procedure1

a.

Replace the stereo component amplifier assembly with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL



b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

d.

None



A

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

B

REPLACE RADIO RECEIVER ASSEMBLY