Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0453794 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Display does not Dim when Light Control Switch is Turned ON  


DESCRIPTION

When the navigation system is activated with the light control switch in the tail or head, before AVC-LAN communication is established, the multi-display assembly dims the display according to the illumination signal received via a direct line.

After AVC-LAN communication is established, the multi-display assembly dims the display according to a dimmer signal sent via AVC-LAN communication.

The radio receiver assembly switches between the daytime screen and night screen on the multi-display assembly according to the illumination signal input.

WIRING DIAGRAM

E444878E04
0.708,0.698 2.542,1.208 1.833,0.51 10 false from PANEL D Relay 0.844,4.396 3.115,4.635 2.271,0.24 10 false : AVC-LAN Communication Line 4.896,0.573 5.49,0.833 0.594,0.26 10 false 2 4.854,1.063 5.448,1.323 0.594,0.26 10 false 13 5.115,0.677 5.708,0.938 0.594,0.26 10 false ILL 5.125,1.167 5.719,1.427 0.594,0.26 10 false GND1 4.844,1.583 5.438,1.844 0.594,0.26 10 false D60 4.854,1.75 6.333,1.969 1.479,0.219 10 false Multi-display Assembly 4.74,2.646 5.333,2.906 0.594,0.26 10 false 15 4.729,2.875 5.323,3.135 0.594,0.26 10 false D64 5.125,2.875 5.719,3.135 0.594,0.26 10 false ILL+ 5.125,3.51 5.719,3.771 0.594,0.26 10 false GND1 4.771,3.302 5.365,3.563 0.594,0.26 10 false 1 4.708,3.521 5.302,3.781 0.594,0.26 10 false D61 4.667,3.906 6.438,4.177 1.771,0.271 10 false Radio Receiver Assembly

PROCEDURE

1.CHECK SYMPTOMS
a.

Check the symptoms that occur by viewing the display.

HINT:
·

When the navigation system is activated with the light control switch in the tail or head, before AVC-LAN communication is established, the multi-display assembly dims the display according to the illumination signal received via a direct line.

·

After AVC-LAN communication is established, the multi-display assembly dims the display according to a dimmer signal sent via AVC-LAN communication.

·

The radio receiver assembly switches between the daytime screen and night screen on the multi-display assembly according to the illumination signal input.




Result:
Result Proceed to
There is a delay until the display dims after the navigation system is activated with the light control switch in the tail or head. A
The display dims for a moment and then becomes bright after the navigation system is activated with the light control switch in the tail or head. B
When the light control switch is set to the tail or head, the display dims but does not switch to the night screen.
When the light control switch is set to the tail or head, the display neither dims nor switches to the night screen. C



A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

3.CHECK IMAGE QUALITY SETTING

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the D60 multi-display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D60)Location & Routing

Click Connector(D60)Instrument Panel>Instrument Panel Wire>Multi-Display Assembly

D60-13 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D60)Location & Routing

Click Connector(D60)Instrument Panel>Instrument Panel Wire>Multi-Display Assembly

D60-2 (ILL) - D60-13 (GND1) Ignition switch off
Light control switch in tail or head
11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK IMAGE QUALITY SETTING
a.

Turn the light control switch to the tail or head position.


b.

Check that the daytime screen setting on the display adjustment screen is set to on.


Result:
Result Proceed to
Daytime screen setting is set to on. A
Daytime screen setting is set to off. B



A

CHANGE DAYTIME SCREEN SETTING TO OFF

B

4.CHECK VEHICLE SIGNAL (OPERATION CHECK)
4.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E225854

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

Check that the display changes between ON and OFF according to the light control switch operation.

OK:
Light Control Switch Display
Tail or head ON
except Tail or head OFF


HINT:
·

This display is updated once per second. As a result, it is normal for the display to lag behind the actual switch operation.

·

Make sure to move the vehicle to a bright area before performing an operation check with the light control switch in the AUTO position.




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the D64 and D61 radio receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D61)Location & Routing

Click Connector(D61)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D61-1 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D64,D61)Location & Routing

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(D61)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D64-15 (ILL+) - D61-1 (GND1) Ignition switch off
Light control switch in tail or head
11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR