Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0453794 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit  


DESCRIPTION

w/ Telematics Transceiver:

·

The radio receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the telematics transceiver sends power to the telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio receiver assembly and navigation ECU assembly via the telematics transceiver.


w/o Telematics Transceiver:

·

The radio receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the radio receiver assembly sends power to the telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio receiver assembly and navigation ECU assembly.


WIRING DIAGRAM

E362164E28
1.479,0.615 2.094,0.813 0.615,0.198 10 false SNS2 5.938,0.625 6.552,0.823 0.615,0.198 10 false SNS2 5.958,1.188 6.573,1.385 0.615,0.198 10 false MIN+ 5.969,1.75 6.583,1.948 0.615,0.198 10 false MIN- 5.948,2.323 6.563,2.521 0.615,0.198 10 false SGND 5.969,5.354 6.583,5.552 0.615,0.198 10 false SGND 3.427,2.865 4.042,3.063 0.615,0.198 10 false SGND 5.563,0.635 6.177,0.833 0.615,0.198 10 false D64 5.563,4.26 6.177,4.458 0.615,0.198 10 false D62 5.948,4.25 6.563,4.448 0.615,0.198 10 false MCO+ 5.958,4.813 6.573,5.01 0.615,0.198 10 false MCO- 3.979,4.25 4.594,4.448 0.615,0.198 10 false MIC+ 3.99,4.802 4.604,5 0.615,0.198 10 false MIC- 3.052,5.688 3.667,5.885 0.615,0.198 10 false D65 3.094,3.198 3.708,3.396 0.615,0.198 10 false D68 0.469,2.667 1.083,2.865 0.615,0.198 10 false H17 1.448,1.177 2.063,1.375 0.615,0.198 10 false MACC 1.458,1.729 2.073,1.927 0.615,0.198 10 false MCO+ 1.469,2.281 2.083,2.479 0.615,0.198 10 false MCO- 3.427,1.75 4.042,1.948 0.615,0.198 10 false MCI+ 3.427,2.302 4.042,2.5 0.615,0.198 10 false MCI- 3.417,1.188 4.031,1.385 0.615,0.198 10 false MCVD 3.885,1.177 4.5,1.375 0.615,0.198 10 false MCO+ 3.906,1.719 4.521,1.917 0.615,0.198 10 false MCO- 5.844,5.698 6.833,6.135 0.99,0.438 10 false Radio Receiver Assembly 3.042,5.865 4.771,6.271 1.729,0.406 10 false Navigation ECU Assembly 3.094,3.365 5.521,3.583 2.427,0.219 10 false Telematics Transceiver 0.469,2.833 1.885,3.281 1.417,0.448 10 false Telephone Microphone Assembly 2,0.521 2.615,0.719 0.615,0.198 10 false 3 2.01,1.073 2.625,1.271 0.615,0.198 10 false 1 2.01,1.625 2.625,1.823 0.615,0.198 10 false 2 2.01,2.188 2.625,2.385 0.615,0.198 10 false 4 3.167,1.073 3.781,1.271 0.615,0.198 10 false 5 3.167,1.635 3.781,1.833 0.615,0.198 10 false 6 3.167,2.188 3.781,2.385 0.615,0.198 10 false 7 3.167,2.74 3.781,2.938 0.615,0.198 10 false 23 4.406,1.083 5.021,1.281 0.615,0.198 10 false 16 4.406,1.635 5.021,1.833 0.615,0.198 10 false 32 5.615,0.427 6.229,0.625 0.615,0.198 10 false 25 5.615,0.99 6.229,1.188 0.615,0.198 10 false 21 5.615,1.552 6.229,1.75 0.615,0.198 10 false 22 5.625,2.104 6.24,2.302 0.615,0.198 10 false 24 4.406,4.156 5.021,4.354 0.615,0.198 10 false 13 4.417,4.708 5.031,4.906 0.615,0.198 10 false 14 5.615,4.063 6.229,4.26 0.615,0.198 10 false 25 5.615,4.625 6.229,4.823 0.615,0.198 10 false 26 5.625,5.167 6.24,5.365 0.615,0.198 10 false 24 5.583,1.198 6.198,1.396 0.615,0.198 10 false D64 5.583,1.76 6.198,1.958 0.615,0.198 10 false D64 5.573,2.323 6.188,2.521 0.615,0.198 10 false D64 5.563,4.833 6.177,5.031 0.615,0.198 10 false D62 5.583,5.365 6.198,5.563 0.615,0.198 10 false D62 0.188,0.031 3.865,0.438 3.677,0.406 12 false w/ Telematics Transceiver: 2.75,2.573 3.365,2.771 0.615,0.198 10 false * 4.896,2.031 5.51,2.229 0.615,0.198 10 false * 4.906,5.083 5.521,5.281 0.615,0.198 10 false * 0.271,6.354 2.125,6.771 1.854,0.417 10 false *: Shielded

E377486E37
0.094,0.073 2.396,0.302 2.302,0.229 12 false w/o Telematics Transceiver: 1.49,0.875 2,1.094 0.51,0.219 10 false SNS2 1.438,1.448 1.948,1.667 0.51,0.219 10 false MACC 1.427,1.99 1.938,2.208 0.51,0.219 10 false MCO+ 1.469,2.563 1.979,2.781 0.51,0.219 10 false MCO- 0.406,2.938 0.917,3.156 0.51,0.219 10 false H17 0.417,3.115 1.823,3.49 1.406,0.375 10 false Telephone Microphone Assembly 2.042,0.76 2.552,0.979 0.51,0.219 10 false 3 2.042,1.281 2.552,1.5 0.51,0.219 10 false 1 2.052,1.875 2.563,2.094 0.51,0.219 10 false 2 2.052,2.438 2.563,2.656 0.51,0.219 10 false 4 5.615,0.667 6.125,0.885 0.51,0.219 10 false 25 5.563,0.885 6.073,1.104 0.51,0.219 10 false D64 5.615,1.24 6.125,1.458 0.51,0.219 10 false 23 5.615,1.792 6.125,2.01 0.51,0.219 10 false 21 5.604,2.365 6.115,2.583 0.51,0.219 10 false 22 5.604,2.917 6.115,3.135 0.51,0.219 10 false 24 5.969,0.885 6.479,1.104 0.51,0.219 10 false SNS2 5.958,1.438 6.469,1.656 0.51,0.219 10 false MACC 5.958,1.99 6.469,2.208 0.51,0.219 10 false MIN+ 5.958,2.552 6.469,2.771 0.51,0.219 10 false MIN- 5.958,3.104 6.469,3.323 0.51,0.219 10 false SGND 5.958,4.323 6.469,4.542 0.51,0.219 10 false MCO+ 5.969,5.438 6.479,5.656 0.51,0.219 10 false SGND 5.958,4.896 6.469,5.115 0.51,0.219 10 false MCO- 5.615,4.156 6.125,4.375 0.51,0.219 10 false 25 5.573,4.354 6.083,4.573 0.51,0.219 10 false D62 5.604,4.698 6.115,4.917 0.51,0.219 10 false 26 5.615,5.229 6.125,5.448 0.51,0.219 10 false 24 4.417,4.219 4.927,4.438 0.51,0.219 10 false 13 4.417,4.781 4.927,5 0.51,0.219 10 false 14 3.969,4.333 4.479,4.552 0.51,0.219 10 false MIC+ 3.979,4.896 4.49,5.115 0.51,0.219 10 false MIC- 3.406,5.792 3.917,6.01 0.51,0.219 10 false D65 3.417,5.979 4.917,6.208 1.5,0.229 10 false Navigation ECU 5.885,5.792 6.906,6.271 1.021,0.479 10 false Radio Receiver Assembly 5.573,4.927 6.083,5.146 0.51,0.219 10 false D62 5.573,5.448 6.083,5.667 0.51,0.219 10 false D62 5.563,1.458 6.073,1.677 0.51,0.219 10 false D64 5.573,2.021 6.083,2.24 0.51,0.219 10 false D64 5.573,2.552 6.083,2.771 0.51,0.219 10 false D64 5.563,3.125 6.073,3.344 0.51,0.219 10 false D64 3.594,2.875 4.104,3.094 0.51,0.219 10 false * 0.271,6.281 1.448,6.625 1.177,0.344 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one. (w/ Telematics Transceiver)



PROCEDURE

1.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO NAVIGATION ECU ASSEMBLY)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to navigation ECU assembly) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check results are normal.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO RECEIVER ASSEMBLY)
2.CHECK MICROPHONE AND VOICE RECOGNITION (INPUT TO RADIO RECEIVER ASSEMBLY)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone (Input to radio receiver assembly) in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check results are normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NAVIGATION ECU ASSEMBLY)

NG

5.CHECK VEHICLE TYPE
3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NAVIGATION ECU ASSEMBLY)
a.

Disconnect the D62 radio receiver assembly connector.


b.

Disconnect the D65 navigation ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D62,D65)Location & Routing

Click Connector(D62)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(D65)Instrument Panel>Instrument Panel Wire>Navigation ECU Assembly

D62-25 (MCO+) - D65-13 (MIC+) Always Below 1 Ω
D62-26 (MCO-) - D65-14 (MIC-) Always Below 1 Ω
D62-25 (MCO+) or D65-13 (MIC+) - Body ground Always 10 kΩ or higher
D62-26 (MCO-) or D65-14 (MIC-) - Body ground Always 10 kΩ or higher
D62-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK RADIO RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK RADIO RECEIVER ASSEMBLY (OUTPUT TO NAVIGATION ECU ASSEMBLY)
a.

Disconnect the D65 navigation ECU assembly connector.


b.
E368005C69
1.5,0.427 1.917,0.677 0.417,0.25 1.75,2.083 1.292,1.469 true 0.833,2.083 1.188,1.469 true 2.813,3.427 3.208,3.656 0.396,0.229 10 false GND 0.656,2.115 1.052,2.344 0.396,0.229 10 false MIC+ 0.167,0.135 0.563,0.365 0.396,0.229 10 false *a 1.583,0.469 1.979,0.698 0.396,0.229 10 false D65 1.646,2.115 2.042,2.344 0.396,0.229 10 false MIC-
*a Front view of wire harness connector
(to Navigation ECU Assembly)


Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal D65-13 (MIC+) - D65-14 (MIC-)
Tool setting 50 mV/DIV., 500 ms./DIV.
Vehicle condition
1.

Ignition switch ACC.

2.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE RADIO RECEIVER ASSEMBLY

5.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Telematics Transceiver A
w/o Telematics Transceiver B



A

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

B

12.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the D64 radio receiver assembly connector.


b.

Disconnect the H17 telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D64,H17)Location & Routing

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assembly

D64-25 (SNS2) - H17-3 (SNS2) Always Below 1 Ω
D64-25 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the D64 radio receiver assembly connector.


b.

Disconnect the D68 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D64,D68)Location & Routing

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D64-21 (MIN+) - D68-16 (MCO+) Always Below 1 Ω
D64-22 (MIN-) - D68-32 (MCO-) Always Below 1 Ω
D64-21 (MIN+) - Body ground Always 10 kΩ or higher
D64-22 (MIN-) - Body ground Always 10 kΩ or higher
D64-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the D68 telematics transceiver connector.


b.

Disconnect the H17 telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D68,H17)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assembly

D68-5 (MCVD) - H17-1 (MACC) Always Below 1 Ω
D68-6 (MCI+) - H17-2 (MCO+) Always Below 1 Ω
D68-7 (MCI-) - H17-4 (MCO-) Always Below 1 Ω
D68-5 (MCVD) - Body ground Always 10 kΩ or higher
D68-6 (MCI+) - Body ground Always 10 kΩ or higher
D68-7 (MCI-) - Body ground Always 10 kΩ or higher
D68-23 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TELEMATICS TRANSCEIVER
a.
E427105C58
1.521,0.615 1.948,0.865 0.427,0.25 2.24,1.719 2.458,0.542 2.458,0.542 2.667,0.542 true 2.406,1.708 2.563,0.948 2.563,0.948 2.74,0.948 true 2.646,2.615 2.479,2.615 2.479,2.615 2.292,1.813 true 0.24,0.135 0.552,0.292 0.313,0.156 10 false *a 2.729,0.479 3.125,0.635 0.396,0.156 10 false MCI- 2.802,0.875 3.302,1.052 0.5,0.177 10 false MCVD 2.708,2.573 3.208,2.75 0.5,0.177 10 false SGND 1.615,0.667 2.156,0.885 0.542,0.219 10 false D68
*a Component with harness connected
(Telematics Transceiver)


Remove the telematics transceiver with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D68)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D68-5 (MCVD) - Body ground Ignition switch ON 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D68)Location & Routing

Click Connector(D68)Instrument Panel>Instrument Panel Wire>Telematics Transceiver

D68-23 (SGND) - Body ground Always Below 1 Ω
D68-7 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK TELEPHONE MICROPHONE ASSEMBLY (OUTPUT TO TELEMATICS TRANSCEIVER)

NG

10.CHECK TELEPHONE MICROPHONE ASSEMBLY (OUTPUT TO TELEMATICS TRANSCEIVER)
E456925C01
1.5,0.313 1.906,0.573 0.406,0.26 1.063,0.542 1.25,0.542 1.25,0.542 1.448,1.24 true 2.365,0.552 2.177,0.552 2.177,0.552 1.938,1.229 true 0.365,0.448 0.677,0.646 0.313,0.198 10 false *a 2.833,3.448 3.292,3.646 0.458,0.198 10 false GND 1.594,0.365 1.958,0.563 0.365,0.198 10 false H17 0.625,0.448 1.24,0.646 0.615,0.198 10 false MCO- 2.448,0.469 3.063,0.667 0.615,0.198 10 false MCO+
*a Component with harness connected
(Telephone Microphone Assembly)


a.

Check the output waveform.

i.

Remove the telephone microphone assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL


ii.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H17-2 (MCO+) - H17-4 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Ignition switch ON

2.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.




Result:
Proceed to
OK
NG



OK

11.CHECK TELEMATICS TRANSCEIVER (OUTPUT TO RADIO RECEIVER ASSEMBLY)

NG

11.CHECK TELEMATICS TRANSCEIVER (OUTPUT TO RADIO RECEIVER ASSEMBLY)
E423925C61
1.5,0.229 1.906,0.49 0.406,0.26 0.885,1.115 0.698,0.438 0.698,0.438 0.542,0.438 true 0.906,1.219 0.74,1.958 0.74,1.958 0.583,1.958 true 0.354,0.031 0.667,0.229 0.313,0.198 10 false *a 1.594,0.281 2.083,0.479 0.49,0.198 10 false D68 0.083,0.354 0.698,0.552 0.615,0.198 10 false MCO+ 0.177,1.865 0.792,2.063 0.615,0.198 10 false MCO- 2.823,3.458 3.24,3.656 0.417,0.198 10 false GND
*a Component with harness connected
(Telematics Transceiver)


a.

Check the output waveform.

i.

Remove the telematics transceiver with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


ii.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal D68-16 (MCO+) - D68-32 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Ignition switch ON

2.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.




Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

12.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the D64 radio receiver assembly connector.


b.

Disconnect the H17 telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D64,H17)Location & Routing

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(H17)Body>No. 1 Roof Wire>Telephone Microphone Assembly

D64-25 (SNS2) - H17-3 (SNS2) Always Below 1 Ω
D64-23 (MACC) - H17-1 (MACC) Always Below 1 Ω
D64-21 (MIN+) - H17-2 (MCO+) Always Below 1 Ω
D64-22 (MIN-) - H17-4 (MCO-) Always Below 1 Ω
D64-25 (SNS2) - Body ground Always 10 kΩ or higher
D64-23 (MACC) - Body ground Always 10 kΩ or higher
D64-21 (MIN+) - Body ground Always 10 kΩ or higher
D64-22 (MIN-) - Body ground Always 10 kΩ or higher
D64-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK RADIO RECEIVER ASSEMBLY
a.
E362172C41
1.583,0.896 1.99,1.156 0.406,0.26 2.021,2.198 2.271,3.177 2.271,3.177 2.385,3.177 true 2.167,2.198 2.531,2.76 2.531,2.76 2.646,2.76 true 1.156,2.719 1.302,2.719 1.302,2.719 1.865,2.177 true 2.448,3.094 2.906,3.292 0.458,0.198 10 false MACC 1.677,0.948 2.135,1.146 0.458,0.198 10 false D64 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 2.708,2.688 3.167,2.885 0.458,0.198 10 false MIN- 0.729,2.635 1.188,2.833 0.458,0.198 10 false SGND
*a Component with harness connected
(Radio Receiver Assembly)


Remove the radio receiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D64)Location & Routing

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D64-23 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D64)Location & Routing

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D64-22 (MIN-) - Body ground Always Below 1 Ω
D64-24 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK TELEPHONE MICROPHONE ASSEMBLY (OUTPUT TO TELEMATICS TRANSCEIVER)

NG

REPLACE RADIO RECEIVER ASSEMBLY

14.CHECK TELEPHONE MICROPHONE ASSEMBLY (OUTPUT TO TELEMATICS TRANSCEIVER)
E456925C02
1.5,0.313 1.906,0.573 0.406,0.26 1.063,0.542 1.25,0.542 1.25,0.542 1.448,1.24 true 2.365,0.552 2.177,0.552 2.177,0.552 1.938,1.229 true 0.365,0.448 0.677,0.646 0.313,0.198 10 false *a 2.833,3.448 3.292,3.646 0.458,0.198 10 false GND 1.594,0.365 1.958,0.563 0.365,0.198 10 false H17 0.625,0.448 1.24,0.646 0.615,0.198 10 false MCO- 2.448,0.469 3.063,0.667 0.615,0.198 10 false MCO+
*a Component with harness connected
(Telephone Microphone Assembly)


a.

Check the output waveform.

i.

Remove the telephone microphone assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL


ii.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H17-2 (MCO+) - H17-4 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Ignition switch ON

2.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm (4.92 in.) from the telephone microphone assembly sound holes in the microphone case.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.




Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG