Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0453794 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio receiver assembly.

WIRING DIAGRAM

E393688E98
0.438,0.771 2.271,0.969 1.833,0.198 10 false from Auxiliary Battery 0.646,1.583 2.792,1.781 2.146,0.198 10 false from ACC D Relay 0.365,2.365 3.427,2.563 3.063,0.198 10 false from IG1 P NO.1 Relay 3.594,0.958 4.542,1.219 0.948,0.26 10 false TV 3.469,1.75 4.542,1.948 1.073,0.198 10 false ACC D 3.333,2.552 5.323,2.75 1.99,0.198 10 false IG1 P NO.1 5.438,0.792 5.75,0.99 0.313,0.198 10 false D61 5.417,2.385 5.729,2.583 0.313,0.198 10 false D64 5.51,0.604 5.667,0.802 0.156,0.198 10 false 4 5.469,1.375 5.781,1.573 0.313,0.198 10 false 15 5.458,2.156 5.771,2.354 0.313,0.198 10 false 19 5.5,2.948 5.656,3.146 0.156,0.198 10 false 1 5.792,0.792 6.25,0.99 0.458,0.198 10 false +B1 5.792,1.594 6.406,1.792 0.615,0.198 10 false ACC1 5.823,2.406 6.135,2.604 0.313,0.198 10 false IG 5.802,3.167 6.417,3.365 0.615,0.198 10 false GND1 5.344,3.646 7.073,4.031 1.729,0.385 10 false Radio Receiver Assembly 5.438,1.594 5.75,1.792 0.313,0.198 10 false D61 5.448,3.177 5.76,3.375 0.313,0.198 10 false D61

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the D61 and D64 radio receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D61)Location & Routing

Click Connector(D61)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D61-1 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D61,D64)Location & Routing

Click Connector(D61)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(D64)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D61-4 (+B1) - D61-1 (GND1) Ignition switch off 11 to 14 V
D61-15 (ACC1) - D61-1 (GND1) Ignition switch ACC 11 to 14 V
D64-19 (IG) - D61-1 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR