READ DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Driving distance | Min.: 0
Max.: 999999 |
- | - |
| Total Distance Traveled - Unit | Driving distance unit | km or mile | - | - |
| Tilt Up Limit | Uppermost tilt position | Not Memory or Memory | Not Memory: Position not memorized
Memory: Position memorized |
- |
| Tilt Down Limit | Lowermost tilt position | Not Memory or Memory | Not Memory: Position not memorized
Memory: Position memorized |
- |
| Telescopic Short Limit | Shortest telescopic position | Not Memory or Memory | Not Memory: Position not memorized
Memory: Position memorized |
- |
| Telescopic Long Limit | Longest telescopic position | Not Memory or Memory | Not Memory: Position not memorized
Memory: Position memorized |
- |
| Tilt&Telescopic Memory 1 (Driver1 Tilt&Telescopic Memory 1) | Driver1 tilt and telescopic memory position 1 | Not Memory or Memory | Not Memory: Position not memorized
Memory: Position memorized |
For Driver1 Tilt&Telescopic Memory 1 |
| Tilt&Telescopic Memory 2 (Driver1 Tilt&Telescopic Memory 2) | Driver1 tilt ilt and telescopic memory position 2 | Not Memory or Memory | Not Memory: Position not memorized
Memory: Position memorized |
For Driver1 Tilt&Telescopic Memory 2 |
| Tilt&Telescopic Memory 3 (Driver1 Tilt&Telescopic Memory 3) | Driver1 tilt ilt and telescopic memory position 3 | Not Memory or Memory | Not Memory: Position not memorized
Memory: Position memorized |
For Driver1 Tilt&Telescopic Memory 3 |
| Driver Information Memory 1 (Driver1 Tilt&Telescopic Memory Last) | Driver1 tilt and telescopic memory position last | Not Memory or Memory | Not Memory: Position not memorized
Memory: Position memorized |
For Driver1 Tilt&Telescopic Memory Last |
| Driver Information Memory 2 (Driver2 Tilt&Telescopic Memory 1) | Driver2 tilt and telescopic memory position 1 | Not Memory or Memory | Not Memory: Position not memorized
Memory: Position memorized |
For Driver2 Tilt&Telescopic Memory 1 |
| Driver Information Memory 3 (Driver2 Tilt&Telescopic Memory 2) | Driver2 tilt and telescopic memory position 2 | Not Memory or Memory | Not Memory: Position not memorized
Memory: Position memorized |
For Driver2 Tilt&Telescopic Memory 2 |
| Ignition Switch (CAN) | Communication state of ignition switch | OFF or ON | OFF: Communication interrupted
ON: Communication normal |
- |
| Handle Position | Steering wheel position signal | Away or Return | Away: Steering wheel in away position
Return: Steering wheel in return position |
- |
| Ignition Switch | Input state of ignition switch | OFF or ON | OFF: Input signal interrupted
ON: Input signal normal |
- |
| Tilt Manual Switch Up | Input state of tilt up switch | OFF or ON | ON: When tilt and telescopic switch up operation performed | - |
| Tilt Manual Switch Down | Input state of tilt down switch | OFF or ON | ON: When tilt and telescopic switch down operation performed | - |
| Telescopic Manual Switch Short | Input state of telescopic contract switch | OFF or ON | ON: When tilt and telescopic switch short operation performed | - |
| Telescopic Manual Switch Long | Input state of telescopic extend switch | OFF or ON | ON: When tilt and telescopic switch long operation performed | - |
| Tilt&Telescopic Manual Switch Voltage | Voltage data of tilt and telescopic switch | Min.: 0.000 V
Max.: 4.998 V |
Neutral position: Below 0.20 V
Tilt up: 1.67 to 2.13 V Tilt down: 0.54 to 0.74 V Telescopic contract: 1.08 to 1.40 V Telescopic extend: 2.22 to 2.77 V |
- |
| ECU Power Source Voltage | Voltage data of power supply | Min.: 0.000 V
Max.: 19.992 V |
11.00 to 14.00 V | - |
| Tilt Position | Current tilt position data | Min.: 0
Max.: 65535 |
28627 to 36864 | - |
| Telescopic Position | Current telescopic position data | Min.: 0
Max.: 65535 |
28627 to 36864 | - |
| Tilt Return Memory Position | Memorized tilt return position data | Min.: 0
Max.: 65535 |
28627 to 36864 | - |
| Telescopic Return Memory Position | Memorized telescopic return position data | Min.: 0
Max.: 65535 |
28627 to 36864 | - |
| Tilt Up Limit Position | Uppermost tilt position data | Min.: 0
Max.: 65535 |
28627 to 36864 | - |
| Tilt Down Limit Position | Lowermost tilt position data | Min.: 0
Max.: 65535 |
28627 to 36864 | - |
| Telescopic Short Limit Position | Shortest telescopic position data | Min.: 0
Max.: 65535 |
28627 to 36864 | - |
| Telescopic Long Limit Position | Longest telescopic position data | Min.: 0
Max.: 65535 |
28627 to 36864 | - |
| Tilt Memory Position 1 (Driver1 Tilt Memory Position 1) | Driver1 tilt data of memory position 1 | Min.: 0
Max.: 65535 |
28627 to 36864 | For Driver1 Tilt Memory Position 1 |
| Telescopic Memory Position 1 (Driver1 Telescopic Memory Position 1) | Driver1 telescopic data of memory position 1 | Min.: 0
Max.: 65535 |
28627 to 36864 | For Driver1 Telescopic Memory Position 1 |
| Tilt Memory Position 2 (Driver1 Tilt Memory Position 2) | Driver1 tilt data of memory position 2 | Min.: 0
Max.: 65535 |
28627 to 36864 | For Driver1 Tilt Memory Position 2 |
| Telescopic Memory Position 2 (Driver1 Telescopic Memory Position 2) | Driver1 telescopic data of memory position 2 | Min.: 0
Max.: 65535 |
28627 to 36864 | For Driver1 Telescopic Memory Position 2 |
| Tilt Memory Position 3 (Driver1 Tilt Memory Position 3) | Driver1 tilt data of memory position 3 | Min.: 0
Max.: 65535 |
28627 to 36864 | For Driver1 Tilt Memory Position 3 |
| Telescopic Memory Position 3 (Driver1 Telescopic Memory Position 3) | Driver1 telescopic data of memory position 3 | Min.: 0
Max.: 65535 |
28627 to 36864 | For Driver1 Telescopic Memory Position 3 |
| Vehicle Speed | Vehicle speed data | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations |
- |
| Driver Tilt Memory Position 1 (Driver1 Tilt Memory Position Last) | Driver1 tilt memory position last | Min.: 0
Max.: 65535 |
28627 to 36864 | For Driver1 Tilt Memory Position Last |
| Driver Telescopic Memory Position 1 (Driver1 Telescopic Memory Position Last) | Driver1 telescopic memory position last | Min.: 0
Max.: 65535 |
28627 to 36864 | For Driver1 Telescopic Memory Position Last |
| Driver Tilt Memory Position 2 (Driver2 Tilt Memory Position 1) | Driver2 tilt memory position 1 | Min.: 0
Max.: 65535 |
28627 to 36864 | For Driver2 Tilt Memory Position 1 |
| Driver Telescopic Memory Position 2 (Driver2 Telescopic Memory Position 1) | Driver2 telescopic memory position 1 | Min.: 0
Max.: 65535 |
28627 to 36864 | For Driver2 Telescopic Memory Position 1 |
| Driver Tilt Memory Position 3 (Driver2 Tilt Memory Position 2) | Driver2 tilt memory position 2 | Min.: 0
Max.: 65535 |
28627 to 36864 | For Driver2 Tilt Memory Position 2 |
| Driver Telescopic Memory Position 3 (Driver2 Telescopic Memory Position 2) | Driver2 telescopic memory position 2 | Min.: 0
Max.: 65535 |
28627 to 36864 | For Driver2 Telescopic Memory Position 2 |
| Tilt Motor Machine Lock Memory Data | Tilt motor machine lock memory data | Not Exist or Existed | - | - |
| Telescopic Motor Machine Lock Memory Data | Telescopic motor machine lock memory data | Not Exist or Existed | - | - |
| Autoaway/Return Operation Setting | Autoaway/return operation setting | Tilt&Telescopic OFF, Telescopic ON, Tilt ON or Tilt&Telescopic ON | Tilt&Telescopic OFF: Tilt and telescopic operations prohibited
Telescopic ON: Only telescopic operations permitted Tilt ON: Only tilt operations permitted Tilt&Telescopic ON: Tilt and telescopic operations permitted |
- |
| Tilt Memory Position 1 | Tilt data of memory position 1 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Telescopic Memory Position 1 | Telescopic data of memory position 1 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Tilt Memory Position 2 | Tilt data of memory position 2 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Telescopic Memory Position 2 | Telescopic data of memory position 2 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Tilt Memory Position 3 | Tilt data of memory position 3 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Telescopic Memory Position 3 | Telescopic data of memory position 3 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Tilt&Telescopic Memory 1 | Tilt and telescopic memory position 1 | No Memory or Memory | No Memory: Position not memorized
Memory: Position memorized |
This item is displayed but not used |
| Tilt&Telescopic Memory 2 | Tilt and telescopic memory position 2 | No Memory or Memory | No Memory: Position not memorized
Memory: Position memorized |
This item is displayed but not used |
| Tilt&Telescopic Memory 3 | Tilt and telescopic memory position 3 | No Memory or Memory | No Memory: Position not memorized
Memory: Position memorized |
This item is displayed but not used |
| Driver2 Tilt&Telescopic Memory 3 | Driver2 tilt and telescopic memory position 3 | No Memory or Memory | No Memory: Position not memorized
Memory: Position memorized |
This item is displayed but not used |
| Driver2 Tilt Memory Position 3 | Driver2 tilt memory position 3 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Driver2 Telescopic Memory Position 3 | Driver2 telescopic memory position 3 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Driver2 Tilt Memory Position Last | Driver2 tilt memory position last | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Driver2 Telescopic Memory Position Last | Driver2 telescopic memory position last | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Driver3 Tilt Memory Position 1 | Driver3 tilt memory position 1 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Driver3 Telescopic Memory Position 1 | Driver3 telescopic memory position 1 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Driver3 Tilt Memory Position 2 | Driver3 tilt memory position 2 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Driver3 Telescopic Memory Position 2 | Driver3 telescopic memory position 2 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Driver3 Tilt Memory Position 3 | Driver3 tilt memory position 3 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Driver3 Telescopic Memory Position 3 | Driver3 telescopic memory position 3 | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Driver3 Tilt Memory Position Last | Driver3 tilt memory position last | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Driver3 Telescopic Memory Position Last | Driver3 telescopic memory position last | Min.: 0
Max.: 65535 |
28627 to 36864 | This item is displayed but not used |
| Driver2 Tilt&Telescopic Memory Last | Driver2 tilt and telescopic memory position last | No Memory or Memory | No Memory: Position not memorized
Memory: Position memorized |
This item is displayed but not used |
| Driver3 Tilt&Telescopic Memory 1 | Driver3 tilt and telescopic memory position 1 | No Memory or Memory | No Memory: Position not memorized
Memory: Position memorized |
This item is displayed but not used |
| Driver3 Tilt&Telescopic Memory 2 | Driver3 tilt and telescopic memory position 2 | No Memory or Memory | No Memory: Position not memorized
Memory: Position memorized |
This item is displayed but not used |
| Driver3 Tilt&Telescopic Memory 3 | Driver3 tilt and telescopic memory position 3 | No Memory or Memory | No Memory: Position not memorized
Memory: Position memorized |
This item is displayed but not used |
| Driver3 Tilt&Telescopic Memory Last | Driver3 tilt and telescopic memory position last | No Memory or Memory | No Memory: Position not memorized
Memory: Position memorized |
This item is displayed but not used |
| Autoaway/Return Operation Setting (Driver1) | Autoaway/return operation setting (driver1) | Tilt&Telescopic OFF, Telescopic ON, Tilt ON or Tilt&Telescopic ON | Tilt&Telescopic OFF: Tilt and telescopic operations prohibited
Telescopic ON: Only telescopic operations permitted Tilt ON: Only tilt operations permitted Tilt&Telescopic ON: Tilt and telescopic operations permitted |
This item is displayed but not used |
| Autoaway/Return Operation Setting (Driver2) | Autoaway/return operation setting (driver2) | Tilt&Telescopic OFF, Telescopic ON, Tilt ON or Tilt&Telescopic ON | Tilt&Telescopic OFF: Tilt and telescopic operations prohibited
Telescopic ON: Only telescopic operations permitted Tilt ON: Only tilt operations permitted Tilt&Telescopic ON: Tilt and telescopic operations permitted |
This item is displayed but not used |
| Autoaway/Return Operation Setting (Driver3) | Autoaway/return operation setting (driver3) | Tilt&Telescopic OFF, Telescopic ON, Tilt ON or Tilt&Telescopic ON | Tilt&Telescopic OFF: Tilt and telescopic operations prohibited
Telescopic ON: Only telescopic operations permitted Tilt ON: Only tilt operations permitted Tilt&Telescopic ON: Tilt and telescopic operations permitted |
This item is displayed but not used |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range |
|---|---|---|
| Tilt Motor | Tilt operation | UP/DOWN |
| Telescopic Motor | Telescopic operation | LONG/SHORT |