Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM U

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  TERMINALS OF ECU  


CHECK SHIFT CONTROL ECU


C372243C10
1.656,0.375 2.042,0.625 0.385,0.25 3.458,0.375 3.844,0.625 0.385,0.25 5.188,0.375 5.573,0.625 0.385,0.25 1.719,0.427 2.177,0.625 0.458,0.198 10 false D92 3.531,0.438 3.99,0.635 0.458,0.198 10 false A44 5.26,0.438 5.719,0.635 0.458,0.198 10 false D93 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a
*a Terminals of Shift Control ECU - -


Terminal No. (Symbol) Condition Specified Condition

*1: With the ignition switch ON, disconnect the cable from the negative (-) auxiliary battery terminal and check that the voltage level changes.

*2: Power will be supplied from the shift control supply for only 11 seconds after turning the ignition switch to ON. Therefore, measure the voltage during that time.

A44-1 (MWA) - D93-6 (E01) Ignition switch ON 7.5 to 15.4 V
A44-2 (MVA) - D93-6 (E01) Ignition switch ON 7.5 to 15.4 V
A44-5 (MUA) - D93-6 (E01) Ignition switch ON 7.5 to 15.4 V
A44-12 (BMA1) - D92-1 (E1) Ignition switch off → Ignition switch ON 7.5 to 15.4 V → Below 1 V
A44-16 (RS) - Body ground Always Below 1 Ω
A44-21 (RB) - A44-24 (E2) Ignition switch off → Ignition switch ON 0.4 V or less → 4.9 V or higher
Ignition switch ON, changing the shift state between park (P) and neutral (N) Pulse generation (see waveform 1)
A44-22 (VC) - A44-24 (E2) Ignition switch ON 4.5 to 5.5 V
A44-23 (RA) - A44-24 (E2) Ignition switch off → Ignition switch ON 0.4 V or less → 4.9 V or higher
Ignition switch ON, changing the shift state between park (P) and neutral (N) Pulse generation (see waveform 1)
A44-24 (E2) - D92-1 (E1) Always 0.4 V or less
D92-1 (E1) - Body ground Always Below 1 Ω
D92-3 (SBFS) - D92-1 (E1) Ignition switch ON Pulse generation (see waveform 2)
D92-5 (CA2L) - D92-1 (E1) Ignition switch ON Pulse generation (see waveform 3)
D92-6 (CA2H) - D92-1 (E1) Ignition switch ON Pulse generation (see waveform 3)
D92-8 (CA1L) - D92-1 (E1) Ignition switch ON Pulse generation (see waveform 4)
D92-9 (CA1H) - D92-1 (E1) Ignition switch ON Pulse generation (see waveform 4)
D92-10 (BUB) - D92-1 (E1) Ignition switch ON*2 8 to 15.4 V
D92-11 (EC) - Body ground Always Below 1 Ω
D92-13 (PPOS) - D92-1 (E1) Ignition switch ON, shift state park (P) Pulse generation (see waveform 5)
D92-15 (BL) - D92-1 (E1) Shift state reverse (R) 7.25 to 14.65 V
Shift state not reverse (R) 1 V or less
D92-18 (ACC) - D92-1 (E1) Ignition switch ACC 6 V or higher
D92-20 (IGCT) - D92-1 (E1) Ignition switch ON 6 V or higher
D92-22 (BUBI) - D92-1 (E1) Ignition switch ON Pulse generation (see waveform 6)
D92-24 (BMA2) - D92-1 (E1) Ignition switch ON*1 7.5 to 15.4 V
D92-27 (IG2) - D92-1 (E1) Ignition switch ON 6 V or higher
D92-29 (BUBO) - D92-1 (E1) Ignition switch ON Pulse generation (see waveform 7)
D93-1 (BATT) - D92-1 (E1) Always 8 to 15.4 V
D93-4 (E03) - Body ground Always Below 1 Ω
D93-5 (E02) - Body ground Always Below 1 Ω
D93-6 (E01) - Body ground Always Below 1 Ω
D93-10 (P1) - D92-1 (E1) Ignition switch ON, P position switch not operated 5.8 V or higher
Ignition switch ON, P position switch being pushed and held 2.47 to 5.8 V
D93-12 (INDP) - D92-1 (E1) Shift state park (P) 1 V or less
Shift state not park (P) 8 to 15.4 V
D93-17 (E12) - Body ground Always Below 1 Ω
D93-18 (STP) - D92-1 (E1) Brake pedal depressed 7.17 V or higher
Brake pedal released 2 V or less
D93-19 (VSI1) - D93-24 (E2X1) Ignition switch ON (READY), shift lever in home position 3.605 to 4.255 V
Ignition switch ON (READY), shift lever in D 1.395 to 1.923 V
Ignition switch ON (READY), shift lever in N 0.745 to 1.395 V
Ignition switch ON (READY), shift lever in R 0.3 to 0.745 V
Ignition switch ON (READY), shift lever in Br 2.5 to 3.605 V
D93-20 (VCX1) - D93-24 (E2X1) Ignition switch ON 4.5 to 5.5 V
D93-21 (VSI2) - D93-24 (E2X1) Ignition switch ON (READY), shift lever in home position 3.055 to 3.705 V
Ignition switch ON (READY), shift lever in D 2.08 to 2.5 V
Ignition switch ON (READY), shift lever in N 1.295 to 2.08 V
Ignition switch ON (READY), shift lever in R 0.3 to 1.295 V
Ignition switch ON (READY), shift lever in Br 2.5 to 3.055 V
D93-22 (VCX2) - D93-26 (E2X2) Ignition switch ON 4.5 to 5.5 V
D93-23 (VSI3) - D93-26 (E2X2) Ignition switch ON (READY), shift lever in home position 1.295 to 1.945 V
Ignition switch ON (READY), shift lever in D 3.705 to 4.75 V
Ignition switch ON (READY), shift lever in N 2.92 to 3.705 V
Ignition switch ON (READY), shift lever in R 2.5 to 2.92 V
Ignition switch ON (READY), shift lever in Br 0.3 to 1.295 V
D93-24 (E2X1) - D92-1 (E1) Ignition switch ON 0.4 V or less
D93-25 (VSI4) - D93-26 (E2X2) Ignition switch ON (READY), shift lever in home position 0.745 to 1.395 V
Ignition switch ON (READY), shift lever in D 4.255 to 4.75 V
Ignition switch ON (READY), shift lever in N 3.605 to 4.255 V
Ignition switch ON (READY), shift lever in R 3.077 to 3.605 V
Ignition switch ON (READY), shift lever in Br 0.3 to 0.745 V
D93-26 (E2X2) - D92-1 (E1) Ignition switch ON 0.4 V or less


OSCILLOSCOPE WAVEFORMS


HINT:

Oscilloscope waveform samples are provided here for reference only. Noise and fluctuating waveforms have been omitted.


a.
A380050E02
0.146,1.406 0.604,1.604 0.458,0.198 10 false CH2 2.823,1.021 3.281,1.219 0.458,0.198 10 false GND 2.833,1.677 3.292,1.875 0.458,0.198 10 false GND 0.135,0.677 0.594,0.875 0.458,0.198 10 false CH1

Waveform 1 (Rotation angle sensor signal)

Item Contents
Terminal CH1: A44-23 (RA) - A44-24 (E2)
CH2: A44-21 (RB) - A44-24 (E2)
Equipment setting 2 V/DIV., 200 ms./DIV.
Condition Ignition switch ON, changing the shift state between park (P) and neutral (N)

HINT:

When changing the shift state from park (P) to neutral (N), or neutral (N) to park (P) with the ignition switch on (IG), a waveform will be generated for up to 1.5 seconds.



b.
C372249E02
3.052,1.219 3.396,1.396 0.344,0.177 10 false GND

Waveform 2 (Fail-safe signal)

Item Contents
Terminal D92-3 (SBFS) - D92-1 (E1)
Equipment setting 10 V/DIV., 20 ms./DIV.
Condition Ignition switch ON

HINT:

The waveforms differ when the shift control ECU is malfunctioning.



c.
C372827E02
3.021,1.125 3.427,1.302 0.406,0.177 10 false GND1 3.021,1.375 3.427,1.542 0.406,0.167 10 false GND2 0.406,0.563 0.865,0.76 0.458,0.198 10 false CH1 0.396,0.99 0.854,1.188 0.458,0.198 10 false CH2

Waveform 3 (CAN communication signal)

Item Contents
Terminal CH1: D92-6 (CA2H) - D92-1 (E1)
CH2: D92-5 (CA2L) - D92-1 (E1)
Equipment setting 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



d.
C372826E02
3.021,1.135 3.427,1.302 0.406,0.167 10 false GND1 3.021,1.365 3.427,1.563 0.406,0.198 10 false GND2 0.385,0.583 0.844,0.781 0.458,0.198 10 false CH1 0.385,0.979 0.844,1.177 0.458,0.198 10 false CH2

Waveform 4 (CAN communication signal)

Item Contents
Terminal CH1: D92-9 (CA1H) - D92-1 (E1)
CH2: D92-8 (CA1L) - D92-1 (E1)
Equipment setting 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



e.
C372252E02
3.063,1.219 3.427,1.417 0.365,0.198 10 false GND

Waveform 5 (Shift state signal)

Item Contents
Terminal D92-13 (PPOS) - D92-1 (E1)
Equipment setting 10 V/DIV., 10 ms./DIV.
Condition Ignition switch ON, shift state park (P)

HINT:

The waveform will vary depending on the shift state.



f.
C372251E01
3.063,1.219 3.375,1.375 0.313,0.156 10 false GND

Waveform 6 (Shift control supply condition signal)

Item Contents
Terminal D92-22 (BUBI) - D92-1 (E1)
Equipment setting 10 V/DIV., 10 ms./DIV.
Condition Ignition switch ON

HINT:

The duty ratio changes according to the vehicle condition.



g.
C372250E01
3.052,1.208 3.375,1.365 0.323,0.156 10 false GND

Waveform 7 (Backup request signal)

Item Contents
Terminal D92-29 (BUBO) - D92-1 (E1)
Equipment setting 10 V/DIV., 10 ms./DIV.
Condition Ignition switch ON

HINT:

The duty ratio changes according to the vehicle condition.