Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM37H0E _53 Suspension _096766 TIRE PRESSURE MONITORING _0454878 TIRE PRESSURE WARNING SYSTEM U

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TERMINALS OF ECU  


CHECK TIRE PRESSURE WARNING ECU AND RECEIVER (excluding JPD20R-CEDSSW (w/ Panic Switch))


a.
C368906C25
0.313,1.01 0.698,1.292 0.385,0.281 0.385,1.073 0.844,1.271 0.458,0.198 10 false G49 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the G49 tire pressure warning ECU and receiver connector and measure the voltage or resistance on the wire harness side.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
G49-1 (IG) - G49-12 (GND) IG power source Ignition switch ON 10 to 16 V
G49-7 (+B) - G49-12 (GND) Power supply (from auxiliary battery) Always 10 to 16 V
G49-9 (CANH) - G49-10 (CANL) CAN communication line Ignition switch off 54 to 69 Ω
G49-12 (GND) - Body ground Ground Always Below 1 Ω


b.

Connect the G49 tire pressure warning ECU and receiver connector.


c.
C250866C04
0.259,0.142 0.496,0.36 0.237,0.217 10 *a
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)


Measure the voltage and resistance according to the value(s) in the table below. If the result is not as specified, the ECU may be malfunctioning.

HINT:

Measure the values on the wire harness side while the connector is connected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
G49-3 (CLSW) - G49-12 (GND) Tire pressure warning reset switch
·

Ignition switch ON

·

Steering pad switch assembly operated, "Change tire pressure" selected on the multi-information display and "OK" switch (steering pad switch assembly) pressed and held


Below 1.5 V
·

Ignition switch ON

·

"OK" switch (steering pad switch assembly) off


8 to 15 V
G49-4 (RDA) - G49-12 (GND) Output signals Ignition switch ON Pulse generation (see waveform 1)
G49-5 (PRG) - G49-12 (GND) Input signals Ignition switch ON Pulse generation (see waveform 1)


d.
C240058C03
2.875,1.229 3.115,1.438 0.24,0.208 10 false *b 0.115,0.104 0.323,0.323 0.208,0.219 10 false *a
*a Example
*b GND


Using an oscilloscope, check waveform 1.

Waveform 1:
Item Contents
Terminal G49-4 (RDA) - G49-12 (GND)
G49-5 (PRG) - G49-12 (GND)
Tool setting 5 V/DIV, 5 ms./DIV.
Vehicle condition Ignition switch ON

HINT:

The waveform shown in the illustration is an example. If the tester displays a waveform that alternates between high and low, where high is a voltage that is between the IG power source voltage and a voltage 2.2 V lower than the IG power source voltage, and where low is a voltage of between 0 and 1.2 V, the ECU can be judged normal.




CHECK TIRE PRESSURE WARNING ECU AND RECEIVER (for JPD20R-CEDSSW (w/ Panic Switch))


a.
C368906C26
0.313,1.01 0.698,1.292 0.385,0.281 0.385,1.073 0.844,1.271 0.458,0.198 10 false G96 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the G96 tire pressure warning ECU and receiver connector and measure the voltage or resistance on the wire harness side.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
G96-1 (IG) - G96-12 (GND) IG power source Ignition switch ON 10 to 16 V
G96-9 (CANH) - G96-10 (CANL) CAN communication line Ignition switch off 54 to 69 Ω
G96-12 (GND) - Body ground Ground Always Below 1 Ω


b.

Connect the G96 tire pressure warning ECU and receiver connector.


c.
C250866C04
0.259,0.142 0.496,0.36 0.237,0.217 10 *a
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)


Measure the voltage and resistance according to the value(s) in the table below. If the result is not as specified, the ECU may be malfunctioning.

HINT:

Measure the values on the wire harness side while the connector is connected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
G96-3 (CLSW) - G96-12 (GND) Tire pressure warning reset switch
·

Ignition switch ON

·

Steering pad switch assembly operated, "Change tire pressure" selected on the multi-information display and "OK" switch (steering pad switch assembly) pressed and held


Below 1.5 V
·

Ignition switch ON

·

"OK" switch (steering pad switch assembly) off


8 to 15 V
G96-4 (RDA2) - G96-12 (GND) Output signals Ignition switch ON Pulse generation (see waveform 1)
G96-5 (PRG2) - G96-12 (GND) Input signals Ignition switch ON Pulse generation (see waveform 1)


d.
C240058C03
2.875,1.229 3.115,1.438 0.24,0.208 10 false *b 0.115,0.104 0.323,0.323 0.208,0.219 10 false *a
*a Example
*b GND


Using an oscilloscope, check waveform 1.

Waveform 1:
Item Contents
Terminal G96-4 (RDA2) - G96-12 (GND)
G96-5 (PRG2) - G96-12 (GND)
Tool setting 5 V/DIV, 5 ms./DIV.
Vehicle condition Ignition switch ON

HINT:

The waveform shown in the illustration is an example. If the tester displays a waveform that alternates between high and low, where high is a voltage that is between the IG power source voltage and a voltage 2.2 V lower than the IG power source voltage, and where low is a voltage of between 0 and 1.2 V, the ECU can be judged normal.