Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2020.11–2021.08
RM37H0E _53 Suspension _096766 TIRE PRESSURE MONITORING _0454878 TIRE PRESSURE WARNING SYSTEM D

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  DIAGNOSIS SYSTEM  


CHECK WARNING LIGHT


NOTICE:
·

When there is a problem with the tire pressure warning system, the tire pressure warning light blinks at 0.5 second intervals, and illuminates after 1 minute.

·

When the malfunction has been corrected, the tire pressure warning light goes off.

·

When the tire pressure warning light illuminates, immediately check the tire pressure of the tires and adjust them to the specified value.

·

After the ignition switch is turned to ON, the tire pressure warning light illuminates for 3 seconds and then goes off. If the warning light does not illuminate for 3 seconds, proceed to the troubleshooting for the tire pressure warning light circuit.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>Tire Pressure Warning Light Circuit



a.
C213286C05
0.616,0.112 0.988,0.358 0.372,0.247 10 *1
*1 Tire Pressure Warning Light


Turn the ignition switch to ON.


b.

Check that the tire pressure warning light illuminates for 3 seconds.



WHAT TO CONSIDER WHEN TIRE PRESSURE WARNING LIGHT ILLUMINATES


a.

When the tire pressure warning light does not go off, or when it illuminates during driving, check the tire pressure. If the tire pressure warning light illuminates within several hours after adjusting the tire pressure, a tire may have a slow air leak.


b.

The system is disabled under the following conditions (when the condition returns to normal, the system will work properly).

i.

When all of the tire and wheel assemblies that have tire pressure warning valve and transmitters registered with the tire pressure warning ECU and receiver have not been installed.


ii.

When all of the transmitter ID codes are not registered with the tire pressure warning ECU and receiver.


iii.

When the tire pressure is abnormally high (absolute pressure: 480 kPa (4.9 kgf/cm2, 70 psi) or more; relative pressure: 380 kPa (3.9 kgf/cm2, 55 psi) or more).


iv.

When a tire pressure warning valve and transmitter battery is depleted.



c.

The system may be disabled under the following conditions (when the condition returns to normal, the system will work properly).

i.

When electric devices or facilities using similar radio frequencies are nearby.


ii.

When a wireless device or other equipment operating at a similar frequency is in use in the vehicle.


iii.

When a window tint that affects radio wave signals is installed.


iv.

When there is a lot of snow or ice on the vehicle, in particular, around the wheels or wheel housing.


v.

When non-genuine wheels are used.


vi.

When tire chains are used.


vii.

When aftermarket tire repair sealant is used.

CAUTION:

After use of tire repair sealant, replacement of the tire pressure warning valve and transmitter is required to ensure normal system operation. (Normal system operation cannot be ensured by only repairing or replacing the tire.)





TIRE PRESSURE WARNING LIGHT AND INDICATOR CHART


HINT:

The table below indicates the state of the tire pressure warning light after the ignition switch is turned to ON.

Immediately after turning the ignition switch to ON Always
Warning light output pattern Multi-information Display Condition
Illuminates for 3 sec. Illuminates for 4 sec. Goes off Illuminates Blinks Outputs DTC Display
Normal ○ - ○ - - - -
Low tire pressure ○ - - ○ - - Tire Pressure Low Check Tire
System failure ○ - - - *1 - TPWS malfunction Visit Your Dealer
HINT:

TPWS is the abbreviation of Tire Pressure Warning


Test mode (signal check mode) ○ - - - *2 - -
Tire pressure initialization - ○ - - - - Setting TPWS
HINT:

TPWS is the abbreviation of Tire Pressure Warning


Tire position identification in progress ○ - ○ - - - -
ECU connector poorly connected - - - - *3 - -
ID certification, automatic ID registration ○ - - - *1 - Registering Each TPWS Sensor
HINT:

TPWS is the abbreviation of Tire Pressure Warning




E133091C10
1.292,1.375 1.802,1.531 0.51,0.156 10 false *c 1.427,0.313 1.646,0.469 0.219,0.156 10 false *c 0.208,0.688 0.458,0.823 0.25,0.135 10 false *a 0.208,1 0.51,1.135 0.302,0.135 10 false *b 1.5,1.781 1.74,1.917 0.24,0.135 10 false *d
*a ON
*b OFF
*c 0.5 sec.
*d 1 minute


*1: Blinks at 0.5 second intervals, and stays illuminated after 1 minute.

C263292C06
0.135,0.844 0.448,1 0.313,0.156 10 false *a 0.135,1.135 0.448,1.292 0.313,0.156 10 false *b 0.938,0.427 1.25,0.583 0.313,0.156 10 false *c 0.667,1.5 0.979,1.656 0.313,0.156 10 false *c
*a ON
*b OFF
*c 0.125 sec.


*2: Blinks at 0.125 second intervals.

C264349C07
1.885,1.51 2.396,1.667 0.51,0.156 10 false *c 1.99,0.208 2.208,0.365 0.219,0.156 10 false *c 0.125,0.698 0.375,0.833 0.25,0.135 10 false *a 0.125,1 0.427,1.135 0.302,0.135 10 false *b 1.969,1.865 2.208,2 0.24,0.135 10 false *d 0.854,0.229 1.104,0.365 0.25,0.135 10 false *e
*a ON
*b OFF
*c 0.5 sec.
*d 1 minute
*e 10 sec.


*3: Goes off for 10 seconds to check the connection of the ECU connector, and then blinks at 0.5 second intervals, and stays illuminated after 1 minute.



NORMAL MODE DTC


a.

DTCs are stored in the tire pressure warning ECU and receiver and output by using the GTS.



TEST MODE (SIGNAL CHECK MODE) DTC


a.

The tire pressure warning ECU and receiver, tire pressure warning valve and transmitter, and initialization signal can be checked by switching from normal mode to test mode (signal check mode/input signal check).

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TEST MODE PROCEDURE