Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM37H0E _55 Steering _097126 POWER ASSIST SYSTEMS _0454879 POWER STEERING SYSTEM U

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU (for LHD)


C450540C02
2.5,3.979 2.917,4.26 0.417,0.281 4.24,2.708 4.708,2.938 0.469,0.229 3.26,3.771 2.74,3.969 false 4.229,2.833 3.927,3.24 true 2.052,2.385 2.365,2.583 0.313,0.198 10 false *a 2.646,4.042 2.958,4.24 0.313,0.198 10 false a1 4.344,2.729 4.802,2.927 0.458,0.198 10 false A80 0.188,0.094 0.5,0.292 0.313,0.198 10 false *A
*A for LHD - -
*a Component without harness connected
(Rack and Pinion Power Steering Gear Assembly)
- -


HINT:
·

The rack and pinion power steering gear assembly uses waterproof connectors. Therefore, voltage or waveforms cannot be checked with the connectors connected to the vehicle.

·

Use the Data List and Active Test on the Techstream to check the operation of the rack and pinion power steering gear assembly and check that communication is established.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST



a1:
Terminal No. (Symbol) Terminal Description
a1-4 (TQG1) Torque sensor A ground
a1-5 (TRQ1) Torque sensor A signal
a1-6 (TRQV) Torque sensor A power source
a1-7 (PGND) Power ground 1
a1-8 (PIG) Power source 1
a1-9 (IG) IG power source 1
a1-10 (CANH) CAN communication line
a1-11 (CANL) CAN communication line

A80:
Terminal No. (Symbol) Terminal Description
A80-4 (TQG2) Torque sensor B ground
A80-5 (TRQ2) Torque sensor B signal
A80-6 (TQV2) Torque sensor B power source
A80-7 (GNDB) Power ground 2
A80-8 (PIGB) Power source 2
A80-9 (IGB) IG power source 2
A80-10 (CA2H) CAN communication line
A80-11 (CA2L) CAN communication line


TERMINALS OF ECU (for RHD)


C450539C02
4.177,2.719 4.573,2.938 0.396,0.219 2.438,4.01 2.854,4.26 0.417,0.25 4.167,2.823 3.677,3.26 true 3.448,3.813 2.646,4.01 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *A 1.865,2.365 2.177,2.563 0.313,0.198 10 false *a 4.25,2.75 4.708,2.948 0.458,0.198 10 false A79 2.542,4.083 3,4.281 0.458,0.198 10 false z11
*A for RHD - -
*a Component without harness connected
(Rack and Pinion Power Steering Gear Assembly)
- -


HINT:
·

The rack and pinion power steering gear assembly uses waterproof connectors. Therefore, voltage or waveforms cannot be checked with the connectors connected to the vehicle.

·

Use the Data List and Active Test on the Techstream to check the operation of the rack and pinion power steering gear assembly and check that communication is established.



A79:
Terminal No. (Symbol) Terminal Description
A79-4 (IG) IG power source
A79-7 (PGND) Power ground
A79-8 (PIG) Power source
A79-10 (CANH) CAN communication line
A79-11 (CANL) CAN communication line

z11:
Terminal No. (Symbol) Terminal Description
z11-1 (TRQV2) Torque sensor B power source
z11-2 (TRQG2) Torque sensor B ground
z11-3 (TRQ2) Torque sensor B signal
z11-5 (TRQ1) Torque sensor A signal
z11-6 (TRQG1) Torque sensor A ground
z11-7 (TRQV1) Torque sensor A power source


CHECK WIRE HARNESS SIDE CONNECTOR (for LHD)


a.

Disconnect the a1 rack and pinion power steering gear assembly connector.

C374510C78
1.917,0.771 2.333,1 0.417,0.229 2.021,0.802 2.479,1 0.458,0.198 10 false a1 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly)
- -



b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Condition Specified Condition
a1-9 (IG) - Body ground Ignition switch ON 8 to 16 V
a1-7 (PGND) - Body ground Always Below 1 Ω
a1-8 (PIG) - Body ground Always 9 to 16 V


c.

Disconnect the A80 rack and pinion power steering gear assembly connector.

C374510C79
1.917,0.771 2.333,1 0.417,0.229 2,0.823 2.458,1.021 0.458,0.198 10 false A80 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly)
- -



d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Condition Specified Condition
A80-9 (IGB) - Body ground Ignition switch ON 8 to 16 V
A80-7 (GNDB) - Body ground Always Below 1 Ω
A80-8 (PIGB) - Body ground Always 9 to 16 V



CHECK WIRE HARNESS SIDE CONNECTOR (for RHD)


a.

Disconnect the A79 rack and pinion power steering gear assembly connector.

C376308C82
3.417,0.115 3.719,0.323 0.302,0.208 3.458,0.156 3.771,0.354 0.313,0.198 10 false A79 0.188,0.125 0.5,0.323 0.313,0.198 10 false *a
- Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly)
- -



b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Condition Specified Condition
A79-4 (IG) - Body ground Ignition switch ON 8 to 16 V
A79-7 (PGND) - Body ground Always Below 1 Ω
A79-8 (PIG) - Body ground Always 9 to 16 V