Home › Vehicle Interior › POWER OUTLETS (INT) › WIRELESS CHARGING SYSTEM
RM37H0E _58 Vehicle Interior _094007 POWER OUTLETS (INT) _0454981 WIRELESS CHARGING SYSTEM J

POWER OUTLETS (INT)  WIRELESS CHARGING SYSTEM  Status Signal Circuit  


DESCRIPTION

This circuit sends a charging suspension signal from the certification ECU (smart key ECU assembly) to the mobile wireless charger cradle assembly. Based on this signal, the mobile wireless charger cradle assembly suspends or resumes wireless charging.

WIRING DIAGRAM

E312443E41
5.49,0.552 5.948,0.75 0.458,0.198 10 false 3.3 V 1.875,1.156 2.5,1.354 0.625,0.198 10 false WCSW 2.458,1.198 2.917,1.396 0.458,0.198 10 false 7 1.167,1.625 1.625,1.823 0.458,0.198 10 false G37 1.167,1.792 2.708,2.177 1.542,0.385 10 false Certification ECU (Smart Key ECU Assembly) 4.219,1.208 4.677,1.406 0.458,0.198 10 false 7 4.438,1.208 4.896,1.406 0.458,0.198 10 false DIS 3.938,2.333 4.396,2.531 0.458,0.198 10 false D103 3.938,2.521 6.927,2.979 2.99,0.458 10 false Mobile Wireless Charger Cradle Assembly 1.646,0.479 2.104,0.677 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.CHECK MOBILE WIRELESS CHARGER CRADLE ASSEMBLY (DIS TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: When the ignition switch is turned from off to ACC, the mobile wireless charger cradle assembly monitors the charging suspension signal for 5 seconds. If the charging suspension signal is not 4 V or more for 0.8 seconds or more during monitoring, the mobile wireless charger cradle assembly determines that there is an open in the charging suspension signal line, blinks (pattern 1) the indicator light (amber), and prohibits operation until the ignition switch is turned from off to ACC again.

Click here(Click here)

*2: For details about conditions when the certification ECU (smart key ECU assembly) sends the charging suspension signal, refer to System Description.

Click here(Click here)

Click Location & Routing(D103)Location & Routing

Click Connector(D103)Instrument Panel>Instrument Panel Wire>Mobile Wireless Charger Cradle Assembly

D103-7 (DIS) - Body ground For 5 seconds after turning ignition switch from off to ACC*1 4.5 to 6.0 V
Device being charged Below 1 V
Charging suspended due to the smart key system status*2 4.5 to 6.0 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - MOBILE WIRELESS CHARGER CRADLE ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - MOBILE WIRELESS CHARGER CRADLE ASSEMBLY)
a.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D103 mobile wireless charger cradle assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G37,D103)Location & Routing

Click Connector(G37)Instrument Panel>Floor Wire>Certification ECU

Click Connector(D103)Instrument Panel>Instrument Panel Wire>Mobile Wireless Charger Cradle Assembly

G37-7 (WCSW) - D103-7 (DIS) Always Below 1 Ω
G37-7 (WCSW) or D103-7 (DIS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR