Home › Vehicle Interior › MIRROR (INT) › DIGITAL REAR-VIEW MIRROR SYSTEM
RM37H0E _58 Vehicle Interior _095286 MIRROR (INT) _0454993 DIGITAL REAR-VIEW MIRROR SYSTEM D

MIRROR (INT)  DIGITAL REAR-VIEW MIRROR SYSTEM  OPERATION CHECK  


HINT:
·

It is only necessary to perform an inspection when there are dents or distortion in the luggage compartment door panel sub-assembly as a result of an accident.

·

Inspections are not required when replacing parts or removing and reinstalling.



CAMERA IMAGE RANGE CONFIRMATION PROCEDURE


a.

Set the vehicle in the position shown in the illustration and create a target on the wall.

NOTICE:
·

Perform this inspection on a level surface.

·

Remove all luggage from the vehicle before starting work.

·

Adjust the tire pressures to the specified pressure before starting work.



E384424C04
0.604,0.688 0.823,0.688 0.823,0.688 1.146,1.052 false 3.385,0.698 3.625,0.438 3.625,0.438 3.854,0.438 false 3.396,2.573 3.635,2.313 3.635,2.313 3.865,2.313 false 1.875,0.177 2.073,0.177 2.073,0.177 2.313,0.302 false 5.646,2.969 5.958,3.302 5.958,3.302 6.115,3.302 false 5.125,3.333 5.302,3.333 5.302,3.333 5.51,3.115 false 5.948,2.313 6.188,2.052 6.188,2.052 6.417,2.052 false 2.708,0.802 2.865,0.802 2.865,0.802 3.031,0.948 false 2.708,2.76 2.865,2.76 2.865,2.76 3.031,2.906 false 1.865,2.219 2.063,2.219 2.063,2.219 2.302,2.344 false 0.344,0.615 0.656,0.771 0.313,0.156 10 false *a 3.927,0.354 4.24,0.51 0.313,0.156 10 false *b 6.198,3.24 6.51,3.396 0.313,0.156 10 false *c 1.656,0.104 1.969,0.26 0.313,0.156 10 false *d 2.615,0.167 2.927,0.323 0.313,0.156 10 false *e 4.594,3.146 4.906,3.302 0.313,0.156 10 false *f 5.427,2.51 5.74,2.76 0.313,0.25 10 false *g 6.313,2.844 6.635,3.031 0.323,0.188 10 false *h 4.927,3.26 5.24,3.417 0.313,0.156 10 false *a 3.917,2.24 4.229,2.396 0.313,0.156 10 false *b 1.667,2.156 1.979,2.313 0.313,0.156 10 false *d 2.635,2.24 2.948,2.396 0.313,0.156 10 false *e 6.5,1.969 6.813,2.177 0.313,0.208 10 false *b 2.49,0.729 2.802,0.885 0.313,0.156 10 false *c 2.49,2.688 2.802,2.844 0.313,0.156 10 false *c
*a Vehicle Center *b Wall, etc.
*c Target *d Vehicle Rear End
*e 100 cm (3.28 ft.) *f 82.7 cm (2.71 ft.)
*g 37.3 cm (1.22 ft.) *h 1.5 cm (0.5906 in.)



b.
E431354C01
1.083,1.958 1.365,1.958 1.365,1.958 1.719,1.469 true 2.271,0.823 2.052,0.823 2.052,0.823 1.844,1.01 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *1 2.365,0.719 2.677,0.875 0.313,0.156 10 false *a 0.854,1.865 1.167,2.021 0.313,0.156 10 false *b
*1 Inner Rear View Mirror Assembly
*a Target
*b Mode Selection Lever


With the ignition switch ON, set the mode selection lever to the digital mirror mode side and check that the target is displayed as shown in the illustration.

HINT:
·

Make sure the system is set to the default settings (position, zoom, etc.).

·

If the target is as shown in the illustration, the system is working correctly.