Home › General › SPECIFICATIONS › Q710 HYBRID TRANSMISSION / TRANSAXLE
RM37H0E _V1 General _095078 SPECIFICATIONS _0455014 Q710 HYBRID TRANSMISSION / TRANSAXLE F

SPECIFICATIONS  Q710 HYBRID TRANSMISSION / TRANSAXLE  SERVICE DATA  


HYBRID TRANSAXLE FLUID

*: Using hybrid transaxle fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transmission of your vehicle.

Hybrid transaxle fluid standard capacity (for Reference) Classification
5.6 liters (5.9 US qts, 4.9 Imp. qts) Toyota Genuine ATF WS*

OIL PUMP (for Mechanical Type)
Condition Specified Condition
Motor Revoluton Transaxle Oil Temperature
3000 to 3200 rpm 20 to 50°C (68 to 122°F) 4.0 kPa (0.04 kgf/cm2, 0.6 psi) or more

HYBRID TRANSAXLE OIL SEAL
Rear drive shaft oil seal RH Standard Depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Rear drive shaft oil seal LH Standard Depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

SHIFT CONTROL ACTUATOR
Shift control actuator seal Installation Depth 6.5 to 7.3 mm (0.256 to 0.287 in.)

TRANSMISSION SHIFT MAIN SWITCH
Tester Connection Condition Specified Condition

Click Location & Routing(D17)Location & Routing

Click Connector(D17)Instrument Panel>Instrument Panel Wire>Parking Switch

D17-2 (S) - D17-9 (E) Switch ON 827 to 914 Ω
D17-2 (S) - D17-9 (E) Switch OFF 4190 to 4631 Ω

Measurement Condition Specified Condition
Battery positive (+) → D17-7 (IND+)
Battery negative (-) → D17-4 (IND-)
Illuminates
Battery positive (+) → D17-1 (ILL+)
Battery negative (-) → D17-10 (ILL-)
Illuminates

PATTERN SELECT SWITCH
No. 1 pattern select switch assembly (DRIVE MODE):
Tester Connection Condition Specified Condition
D5-1 (DMS+) - D5-3 (E) When the DRIVE MODE switch is operated and held on the top side Below 10 Ω
D5-1 (DMS+) - D5-3 (E)
D5-4 (DMS-) - D5-3 (E)
When the DRIVE MODE switch is not operated 10 kΩ or higher
D5-4 (DMS-) - D5-3 (E) When the DRIVE MODE switch is operated and held on the bottom side Below 10 Ω

No. 1 pattern select switch assembly (DRIVE MODE):
Measurement Condition Specified Condition
Battery positive (+) → D5-5 (ILL+)
Battery negative (-) → D5-2 (ILL-)
Illuminates

Pattern select switch assembly (SNOW):
Tester Connection Condition Specified Condition
D74-5 (SNSW) - D74-2 (E) SNOW mode switch pushed and held Below 10 Ω
D74-5 (SNSW) - D74-2 (E) SNOW mode switch not pushed 10 kΩ or higher

Pattern select switch assembly (SNOW):
Measurement Condition Specified Condition
Battery positive (+) → D74-6 (ILL+)
Battery negative (-) → D74-1 (ILL-)
Illuminates

RELAY
OIL PMP MTR RELAY:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminal 1 and 2 10 MΩ or higher
3 - 5 Battery voltage is applied to terminal 1 and 2 Below 1 Ω
P CON MTR RELAY:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminal 1 and 2 10 MΩ or higher
3 - 5 Battery voltage is applied to terminal 1 and 2 Below 1 Ω
IG2 P RELAY:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminal 1 and 2 10 MΩ or higher
3 - 5 Battery voltage is applied to terminal 1 and 2 Below 1 Ω
LUG-IG1 No. 1 RELAY:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminal 1 and 2 10 MΩ or higher
3 - 5 Battery voltage is applied to terminal 1 and 2 Below 1 Ω